|
Ambe3000 dongle
pikam@...
It was working well on Windows 7 but won’t work on Windows 10, Does it need a new driver for Win10??
Nga mihi
Peter Moore 13 Ruataniwha Street Waipawa 4210 068577340
|
|
|
|
Re: Ambeserver
Patrick Perdue
Correct. ambed from XLX isn't compatible with AMBEserver's protocol. For XLX, I use a separate box with two AMBE chips. I tried running multiple ThumbDV's on a Pi with an instance of AMBEserver for each. It didn't work without a USB hub with it's own power supply. I eventually just went back to hosting one ThumbDV per Pi on two Pi boards in two different locations, one to serve as a backup for my Allstar/DMR bridge, and misc access to other modes when that isn't in use.
On 1/26/2020 12:14 PM, Russell, KV4S
wrote:
|
|
|
|
Re: Ambeserver
I'm not sure myself. I only have 1 chip. I've been told amabe server can only handle 1 chip. For xlx transcoding I've been told you install ambed and then the pi can have multiple chips but then it's not working for apps like DVSwitch and blue DV.
On Sun, Jan 26, 2020, 10:26 AM Nomis Bayan Jr. <nolyn78@...> wrote: I followed the instruction fro installing the ambeserver on a Raspebbery Pi and ThumbDV (Installing AMBEserver on a Raspberry Pi and ThumbDV™). The sever is working fine. But When I added another thumbdv with different port, if the other thumbdv is currently being use and I I try to connect to the 2nd thumbdv, it will not connect. Before it was working fine and both thumbdvs are working at the same time with different port same IP address. Not sure why now the 2nd thumbdv will not connect. Verified the status of the thumbdv and both are active. Any advice.
|
|
|
|
Ambeserver
Nomis Bayan Jr.
I followed the instruction fro installing the ambeserver on a Raspebbery Pi and ThumbDV (Installing AMBEserver on a Raspberry Pi and ThumbDV™). The sever is working fine. But When I added another thumbdv with different port, if the other thumbdv is currently being use and I I try to connect to the 2nd thumbdv, it will not connect. Before it was working fine and both thumbdvs are working at the same time with different port same IP address. Not sure why now the 2nd thumbdv will not connect. Verified the status of the thumbdv and both are active. Any advice.
|
|
|
|
#thumbdv Thumbdv suddenly stopped working
#thumbdv
Ryan Matthew Headley
I have used two thunbvs in my the ambed server for xlxd for about six months now. Everything has worked wonderfully.
I rebooted the system running everything this morning, I when I went to start the ambed server, this was the output: --------------------------------------------------------- ryan@ryan:/ambed$ Starting AMBEd 1.3.4 Initializing vocodecs: Detected 2 USB-FTDI devices Description : ThumbDV Serial : DN059GTP Description : FT232EX Serial : Codec interfaces initialized successfully : 0 channels available Initializing controller AMBEd started and listening on 127.0.0.1 ------------------------------------------------------- It looks to me as though the firmware on was on the thumbdvs is corrupted somehow. Is this fixable?
|
|
|
|
Re: AMBE 3000 dongle not recognized by BlueDV
Did you make sure that BlueDV and your Dongle are both on the same baud rate? WB5EKU
On Thu, Jan 2, 2020 at 9:43 PM <pikam@...> wrote:
|
|
|
|
AMBE 3000 dongle not recognized by BlueDV
pikam@...
AMBE dongle is not seen by BlueDV. All I see is a flashing green light for about a second on the dongle then nothing happens, BlueDV screen shows no recognized hardware. HELP
Using Windows 10 and two versions of BlueDV software 9475 and 9570.
Was OK with Windows 7
Com ports are set correctly
Nga mihi
Peter Moore 13 Ruataniwha Street Waipawa 4210 068577340
|
|
|
|
Just a heads up for anyone upgrading to the latest version of BlueDv. Upon installing the upgrade BlueDV appeared to be working well. The only problem was I had no audio. I fought this for a couple of days before getting it resolved. Here is what finally worked….
Originally my system had the default audio driver which Win10 installed when I did the upgrade to Win10. That has always worked until this last install of BlueDV. After screwing around with a lot of things I finally went to the ASUS downloads section, ( maker of my motherboard ) and I downloaded the audio driver for my specific motherboard for Win10. Installing that fixed it!
Honestly I have my doubts the driver was the problem. I think the act of installing a new driver reset something in my system that was keeping it from working. I only post this in case someone else has the same issue maybe this will save them some time troubleshooting.
Regards, David N5BOC
From: ambe@nw-digital-radio.groups.io <ambe@nw-digital-radio.groups.io> On Behalf Of David PA7LIM
Sent: Monday, December 23, 2019 10:56 AM To: ambe@nw-digital-radio.groups.io Subject: Re: [ambe] error when saving setup #bluedv #thumbdv
Upgrade to the latest version 9570 and select an YSF reflector in the setup. Then save.
Greets and 73, David PA7LIM
From: ambe@nw-digital-radio.groups.io <ambe@nw-digital-radio.groups.io> On Behalf Of Merle Watts via Groups.Io
I have a thumbdv and BlueDV for windows.
|
|
|
|
David is the author and authority, please follow his direction on BlueDV.
On Mon, Dec 23, 2019 at 8:56 AM David PA7LIM <info@...> wrote:
--
John D. Hays Kingston, WA K7VE
|
|
|
|
Ludovic Ludo
You have not the last version i suppose.
So update it. Best regards, Ludovic - F5PBG
|
|
|
|
if.only@...
Hi, I too had this problem, on Windows 10 I got the PC to use a suitable mode which turned out to be Windows 8 for that particular prog. and it worked fine then.
Hope that helps. M3VWU
|
|
|
|
Upgrade to the latest version 9570 and select an YSF reflector in the setup. Then save.
Greets and 73, David PA7LIM
From: ambe@nw-digital-radio.groups.io <ambe@nw-digital-radio.groups.io>
On Behalf Of Merle Watts via Groups.Io
Sent: Wednesday, 18 December 2019 23:58 To: ambe@nw-digital-radio.groups.io Subject: [ambe] error when saving setup #bluedv #thumbdv
I have a thumbdv and BlueDV for windows.
|
|
|
|
Cannot make to connection to Brandmeister network
Is there anyway to eliminate this message at the start up of the program? “Cannot make connection to Brandmeister network “. I get it about 50% of the time or more when I start up. All I have to do is click ok and the program runs with no issues. I'm using the latest software.
Frank, W2SDR
|
|
|
|
Merle Watts
I have a thumbdv and BlueDV for windows.
About 2 yrs ago I was in Asia using DMR. and everything was working fine. I updated BlueDV on my laptop and I could no longer get the settings to save. I get an error that says "Object reference not set to an instance of an object". After returning to the US I started getting the same error on my desktop. Any ideas? It's been 2 yrs now and it still doesn't work on either the laptop or the desktop. Both have windows 10.
|
|
|
|
Re: Original ThumbDV and AMBED
Jamie R. Cid <jay@...>
Ok, Thank you!
|
|
|
|
Re: Original ThumbDV and AMBED
Yes, I believe so.
On Mon, Oct 21, 2019 at 8:42 AM Jamie R. Cid <jay@...> wrote: Ow so itll always show 0 unless there's multiple? --
John D. Hays Kingston, WA K7VE
|
|
|
|
Re: Original ThumbDV and AMBED
Jamie R. Cid <jay@...>
Ow so itll always show 0 unless there's multiple?
|
|
|
|
Re: Original ThumbDV and AMBED
Jamie. This is just showing 1 device. Ambed needs at least two channels.
On Mon, Oct 21, 2019, 07:37 Jamie R. Cid <jay@...> wrote: Hi Scott,
|
|
|
|
Re: Original ThumbDV and AMBED
Jamie R. Cid <jay@...>
Hi Scott,
I'm confused, your first post already states that its a "ThumbDV" why would you change it again?? I have the same issue with the new InternetLabs DV3k I'm trying to get working. I did change the baud to 230400 and recompiled with no change. Any ideas? Initializing vocodecs: Detected 1 USB-FTDI devices Description : USB-3000 Serial : DA4AIASF (Changed from DV3k to USB-3000) Codec interfaces initialized successfully : 0 channels available Initializing controller AMBEd started and listening on 127.0.0.1 73,
|
|
|
|
Spiros Xanthopoulos
Hi All...Yesterday everything was working ok, today windows says the application BlueDV has a virus...seen this already but dont know where...Please advice..73 de sv2evs
|
|
|