There is a new C++ rewrite of dsd, the digital speech decoder, that can decode P25, DMR, D-Star etc. It's called dsdcc ( https://github.com/f4exb/dsdcc ) It also supports doing the decoding with a

Also see https://github.com/f4exb/serialDV -- John D. Hays K7VE PO Box 1223, Edmonds, WA 98020-1223

Some things I have noticed; Apparently you need the mbe library even if you use a AMBE dongle... I wasn't able to get around this dependency. On the other side of the coin, apparently you also need

Howdy! I play around on 2m packet a fair bit and am interested in checking out what DStar has to offer. I'm always interested in means of getting MOAR SPEED out of these rigs. Is the PiDV plus my

Hi Rob, The PiDV and ThumbDV are AMBE encoder/decoder devices and don't have anything to do with RF directly. You can get on the D-STAR network with them using software on your computer and

Hello, I am a newbie to linux and setting up my rasbperry pi 3 and my NWDR DV3000 board. I am using the Compass load and have followed all the steps so far but keep getting this error and not sure

Do you have a PiDV (plugs onto a Raspberry Pi Header) or ThumbDV (DV3000 could be either)? https://nw-digital-radio.groups.io/g/ambe/wiki/AMBEserver-Addendum#Managing-the-AMBEserver Note it looks

John, It is a DV3000 pic header. Also thanks for the info on the not O but 0. Makes more sense. I will give it a try. Abbot Sent from Yahoo Mail for iPhone -- 73 Ke8bts Abbot

Thanks for all your help John. I believe I have my system up and running. 73, Abbot Sent from Yahoo Mail for iPhone -- 73 Ke8bts Abbot

Hello, I am having issues while following the instructions on this page. I am using the suggested develop of load. Every time I get to the test I get this error message. I am not sure what I am

Hello Community. So as to check if I understand correctly, it is possible to insert the ThumbDV on a USB port on my Raspberry Pi 3 that has a DVMega installed. System is Compass Linux. So I may

What is the command you are using to start the AMBEserver? Are you using a PiDV or ThumbDV? https://nw-digital-radio.groups.io/g/ambe/wiki/AMBEserver-Addendum -- John D. Hays K7VE PO Box 1223,

Hi John I got it working. This was another post I posted the other day when I could not get my system to work. It can be closed. Working fine now. Thanks, Abbot -- 73 Ke8bts Abbot

Close -- AMBEserver talks to DummyRepeater (or Buster, ...) and DummyRepeater is what talks to ircddbgateway. So the DummyRepeater will select the "DV3000 Network" and the IP/Port of the Raspberry Pi

Hi John. Enjoying the ThumbDV here. It got my attention on the possibility to use it from home. So on my gateway I install AMBE server as per wiki and leave the ThumbDV inserted on a USB Port,

No -- The AMBEserver talks to DummyRepeater (nothing directly to do with ircDDBGateway). DummyRepeater talks to ircDDBGateway. AMBEserver <=== Network AMBE/Voice over UDP ====> DummyRepeater <=====

http://nwdigitalradio.com/dv3000-ambeserver/notes-on-using-ambeserver-with-dummy-repeater/ dummyrepeater will use the network address of the Raspberry Pi to reach the AMBEserver dummyrepeater will

I have not been able to get any of the xrefletors to link on my 3000 breakout board on my pi3. It says linking and then I get an error that it has failed to connect. Any thoughts or suggestions?

OK John, I will install and run and report back. Thank you.

After apt-get update & apt-get upgrade, it encoutered 2 errors, bluez and pi-bluetooth. I did install ambeserver, and got this: Selecting previously unselected package ambeserver. (Reading database