Date   

Re: Original ThumbDV and AMBED

Scott Weis (KB2EAR)
 

I have now confirmed that it does indeed work.

 

Two changes need to be made. First the Product Description needs to be reflashed to read any of the following “ThumbDV" or "DVstick-30" or "USB-3000".  Any of which work fine. I used a program call FT_PROG. https://www.ftdichip.com/Support/Utilities.htm?#FT_PROG

 

 

Second, in the file cusb3000interface.cpp change line    int baudrate = 460800;   to int baudrate = 230400;   Then recompile.

 

And as long as you have 2 devices, or at least 2 channels that it recognizes it works just fine. (I used an AMBE3003 device for the second one.) The software will not initialize with only one. You also can’t have a new 460800 baud and an old 240400 baud ThumbDV on the same system.

 

Hope that helps anyone else going down this road.

 

73,

Scott KB2EAR

 

From: ambe@nw-digital-radio.groups.io [mailto:ambe@nw-digital-radio.groups.io] On Behalf Of John D Hays - K7VE
Sent: Friday, March 15, 2019 2:11 AM
To: ambe@nw-digital-radio.groups.io
Subject: Re: [ambe] Original ThumbDV and AMBED

 

I am not sure if it will work, that is a question for the xlxd group.

 

But besides the baud rate the ThumbDV needs to be programmed with an identifier that the ambed server knows. 

 

On Thu, Mar 14, 2019, 21:59 Scott Weis (KB2EAR) via Groups.Io <kb2ear=kb2ear.net@groups.io> wrote:

Has anyone gotten an original ThumbDV (230400 baud) to work with xlxd/ambed? I have changed to baudrate in the cusb3000interface.cpp. This is what I get:

Starting AMBEd 1.3.2

Initializing vocodecs:
Detected 1 USB-FTDI devices

Description : ThumbDV    Serial : DA00WQFK
Codec interfaces initialized successfully : 0 channels available

Initializing controller

AMBEd started and listening on 127.0.0.1

any ideas?

Thanks & 73,
Scott KB2EAR


Dummyrepeater Issue

Mike Besemer - WM4B
 

Hello all,

Still having issues with getting my PiDV up and running.  Have moved to a Pi 3B+ and now have AMBEserver and ircddbgateway installed and running.  I am using /dev/ttyS0 for the PiDV.  (Both installed from Synaptic Package Manager).  Dummyrepeater was also installed from Synaptic.

When I start AMBEserver, I get a message that it is listening on Port 2460. I also see traffic on ircddbgateway, so I feel confident that both are working.

Dummyrepeater starts normally, but I think there is a configuration issue.  I have a PiDV installed on the Pi 3B+ GPIO pins.

When I go to configure it, as I understand it, under Dongle, I should select DV Serial, but when I do that, dummyrepeater cannot find the dongle.  If I select Network’ and enter the local IP of the Pi, then the dongle is found and I can transmit.  However, when I connect to a reflector, all I get bad is R2D2.  Same for the Echo reflector.

$ sudo python AMBEtest2.py produces:

D

8

N

1

False

False

False

0

Reset

6100010033

Any pointers?

73,

Mike

WM4B


Re: DVSI USB-3000

Lito - WI6Y
 

Hi Dennis,

Did you try running it in the foreground as John suggested?

sudo AMBEserver -i /dev/ttyUSB0 -s 460800 -d

Lito


From: ambe@nw-digital-radio.groups.io <ambe@nw-digital-radio.groups.io> on behalf of Dennis Ramos <m0tfg@...>
Sent: Monday, March 18, 2019 2:46 PM
To: ambe@nw-digital-radio.groups.io
Subject: Re: [ambe] DVSI USB-3000
 
Hello guys, my ambeserver is working now for about 3 days 24/7.

Just noticed that it hang twice so I need to reboot it.

Any idea why? Or any log to check

Thanks

Dennis

On 18 March 2019 20:11:56 GMT, Serdar ULUKONAKCI <ta3as@...> wrote:

Hi John,

I changed the baud rate to 230400. Previous error gone

pi@compass:~ $ sudo AMBEserver -i /dev/ttyUSB0 -s 230400 -d
AMBEserver: Starting...
AMBEserver: Opened serial port /dev/ttyUSB0 at 230400 bps.

But there is a strange behavior. You can see at attached picture.

73!


On 18.03.2019 22:59, Serdar ULUKONAKCI wrote:
Hi John,
Thank you very much for your support.
Yes. USB-3000 is located at USB0
pi@compass:~ $ ls /dev/ttyU*
/dev/ttyUSB0
pi@compass:~ $


and the result after sudo AMBEserver -i /dev/ttyUSB0 -s 460800 -d command.

pi@compass:~ $ sudo AMBEserver -i /dev/ttyUSB0 -s 460800 -d
AMBEserver: Starting...
AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
pi@compass:~ $ AMBEserver: Couldn't find start byte in serial data
AMBEserver: error receiving response to reset
AMBEserver: Could not initialize the DV3K!

73!
Serdar



On 18.03.2019 22:53, John D Hays - K7VE wrote:
This assumes that /dev/ttyUSB0 is your DVSI USB-3000, if not, change accordingly.

On Mon, Mar 18, 2019 at 12:48 PM John D Hays - K7VE via Groups.Io <john=hays.org@groups.io> wrote:
Try running it without using systemd first.

sudo AMBEserver -i /dev/ttyUSB0 -s 460800 -d

Change the baudrate (-s) if it is not 460800 for your device.

There are also python test scripts you use to test, in the github

Like most Unix/Linux commands there is an -h flag for listing the optional flags



On Mon, Mar 18, 2019 at 12:34 PM Serdar ULUKONAKCI <ta3as@...> wrote:
Hi,
I installed AMBEserver on RPI 3B+. Distro  is Compass Linux and DVSI USB3000 is at USB0
â ambeserver@... - DV3000 Daemon
   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)
   Active: active (running) since Mon 2019-03-18 22:27:36 +03; 11s ago
  Process: 994 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
  Process: 991 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
 Main PID: 997 (AMBEserver)
   CGroup: /system.slice/system-ambeserver.slice/ambeserver@...
           ââ997 /usr/sbin/AMBEserver -p 2460 -i /dev/ttyUSB0 -s 460800

Mar 18 22:27:36 compass systemd[1]: Starting DV3000 Daemon...
Mar 18 22:27:36 compass systemd[1]: Started DV3000 Daemon.
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Starting...
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
After few minutes:
pi@compass:/etc/opendv $ sudo systemctl status ambeserver@...
â ambeserver@... - DV3000 Daemon
   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)
   Active: failed (Result: exit-code) since Mon 2019-03-18 22:28:13 +03; 1min 56s ago
  Process: 997 ExecStart=/usr/sbin/AMBEserver -p ${UDP_PORT} -i /dev/ttyUSB0 $AMBESERVER_FLAGS (code=exited, status=1/FAIL
  Process: 994 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
  Process: 991 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
 Main PID: 997 (code=exited, status=1/FAILURE)

Mar 18 22:27:36 compass systemd[1]: Starting DV3000 Daemon...
Mar 18 22:27:36 compass systemd[1]: Started DV3000 Daemon.
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Starting...
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Main process exited, code=exited, status=1/FAILURE
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Unit entered failed state.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Triggering OnFailure= dependencies.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Failed with result 'exit-code'.
What am I doing wrong?
Any help will be appreciated.

73!
TA3AS
On 17.03.2019 21:20, Serdar ULUKONAKCI wrote:
Hi K7VE,
Thank you very much for your answer.
I have one USB-3000 stick. I'll test it on my RaspberryPi. I'll share the results. I read that compass linux is the preferred dist. for AMBEserver. I'll try to  setup it.
73!
TA3AS
On 17.03.2019 21:05, John D Hays - K7VE wrote:
I have not tested the DVSI USB-3000 stick, they're pretty expensive and I haven't purchased one but I can say that we have used the ThumbDV in applications designed for the DVSI stick and it should work but no guarantee.

On Sun, Mar 17, 2019, 08:28 Serdar ULUKONAKCI <ta3as@...> wrote:
Hi,
I think this can be a wrong group but I could not find any group for my
question.
Can a DVSI's USB-3000 stick work with AMBEserver? Is the DVSI's USB-3000
stick is compatible with AMBEserver software?
Any help will be appreciated.
Best Regards,
TA3AS
Serdar






--


John D. Hays
Edmonds, WA
K7VE

   



--


John D. Hays
Edmonds, WA
K7VE

   


Re: DVSI USB-3000

Dennis Ramos
 

Hello guys, my ambeserver is working now for about 3 days 24/7.

Just noticed that it hang twice so I need to reboot it.

Any idea why? Or any log to check

Thanks

Dennis


On 18 March 2019 20:11:56 GMT, Serdar ULUKONAKCI <ta3as@...> wrote:

Hi John,

I changed the baud rate to 230400. Previous error gone

pi@compass:~ $ sudo AMBEserver -i /dev/ttyUSB0 -s 230400 -d
AMBEserver: Starting...
AMBEserver: Opened serial port /dev/ttyUSB0 at 230400 bps.

But there is a strange behavior. You can see at attached picture.

73!


On 18.03.2019 22:59, Serdar ULUKONAKCI wrote:
Hi John,
Thank you very much for your support.
Yes. USB-3000 is located at USB0
pi@compass:~ $ ls /dev/ttyU*
/dev/ttyUSB0
pi@compass:~ $


and the result after sudo AMBEserver -i /dev/ttyUSB0 -s 460800 -d command.

pi@compass:~ $ sudo AMBEserver -i /dev/ttyUSB0 -s 460800 -d
AMBEserver: Starting...
AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
pi@compass:~ $ AMBEserver: Couldn't find start byte in serial data
AMBEserver: error receiving response to reset
AMBEserver: Could not initialize the DV3K!

73!
Serdar



On 18.03.2019 22:53, John D Hays - K7VE wrote:
This assumes that /dev/ttyUSB0 is your DVSI USB-3000, if not, change accordingly.

On Mon, Mar 18, 2019 at 12:48 PM John D Hays - K7VE via Groups.Io <john=hays.org@groups.io> wrote:
Try running it without using systemd first.

sudo AMBEserver -i /dev/ttyUSB0 -s 460800 -d

Change the baudrate (-s) if it is not 460800 for your device.

There are also python test scripts you use to test, in the github

Like most Unix/Linux commands there is an -h flag for listing the optional flags



On Mon, Mar 18, 2019 at 12:34 PM Serdar ULUKONAKCI <ta3as@...> wrote:
Hi,
I installed AMBEserver on RPI 3B+. Distro  is Compass Linux and DVSI USB3000 is at USB0
â ambeserver@... - DV3000 Daemon
   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)
   Active: active (running) since Mon 2019-03-18 22:27:36 +03; 11s ago
  Process: 994 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
  Process: 991 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
 Main PID: 997 (AMBEserver)
   CGroup: /system.slice/system-ambeserver.slice/ambeserver@...
           ââ997 /usr/sbin/AMBEserver -p 2460 -i /dev/ttyUSB0 -s 460800

Mar 18 22:27:36 compass systemd[1]: Starting DV3000 Daemon...
Mar 18 22:27:36 compass systemd[1]: Started DV3000 Daemon.
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Starting...
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
After few minutes:
pi@compass:/etc/opendv $ sudo systemctl status ambeserver@...
â ambeserver@... - DV3000 Daemon
   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)
   Active: failed (Result: exit-code) since Mon 2019-03-18 22:28:13 +03; 1min 56s ago
  Process: 997 ExecStart=/usr/sbin/AMBEserver -p ${UDP_PORT} -i /dev/ttyUSB0 $AMBESERVER_FLAGS (code=exited, status=1/FAIL
  Process: 994 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
  Process: 991 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
 Main PID: 997 (code=exited, status=1/FAILURE)

Mar 18 22:27:36 compass systemd[1]: Starting DV3000 Daemon...
Mar 18 22:27:36 compass systemd[1]: Started DV3000 Daemon.
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Starting...
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Main process exited, code=exited, status=1/FAILURE
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Unit entered failed state.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Triggering OnFailure= dependencies.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Failed with result 'exit-code'.
What am I doing wrong?
Any help will be appreciated.

73!
TA3AS
On 17.03.2019 21:20, Serdar ULUKONAKCI wrote:
Hi K7VE,
Thank you very much for your answer.
I have one USB-3000 stick. I'll test it on my RaspberryPi. I'll share the results. I read that compass linux is the preferred dist. for AMBEserver. I'll try to  setup it.
73!
TA3AS
On 17.03.2019 21:05, John D Hays - K7VE wrote:
I have not tested the DVSI USB-3000 stick, they're pretty expensive and I haven't purchased one but I can say that we have used the ThumbDV in applications designed for the DVSI stick and it should work but no guarantee.

On Sun, Mar 17, 2019, 08:28 Serdar ULUKONAKCI <ta3as@...> wrote:
Hi,
I think this can be a wrong group but I could not find any group for my
question.
Can a DVSI's USB-3000 stick work with AMBEserver? Is the DVSI's USB-3000
stick is compatible with AMBEserver software?
Any help will be appreciated.
Best Regards,
TA3AS
Serdar






--


John D. Hays
Edmonds, WA
K7VE

   



--


John D. Hays
Edmonds, WA
K7VE

   


Re: DVSI USB-3000

Serdar ULUKONAKCI
 

Hi John,

I changed the baud rate to 230400. Previous error gone

pi@compass:~ $ sudo AMBEserver -i /dev/ttyUSB0 -s 230400 -d
AMBEserver: Starting...
AMBEserver: Opened serial port /dev/ttyUSB0 at 230400 bps.

But there is a strange behavior. You can see at attached picture.

73!


On 18.03.2019 22:59, Serdar ULUKONAKCI wrote:
Hi John,
Thank you very much for your support.
Yes. USB-3000 is located at USB0
pi@compass:~ $ ls /dev/ttyU*
/dev/ttyUSB0
pi@compass:~ $


and the result after sudo AMBEserver -i /dev/ttyUSB0 -s 460800 -d command.

pi@compass:~ $ sudo AMBEserver -i /dev/ttyUSB0 -s 460800 -d
AMBEserver: Starting...
AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
pi@compass:~ $ AMBEserver: Couldn't find start byte in serial data
AMBEserver: error receiving response to reset
AMBEserver: Could not initialize the DV3K!

73!
Serdar



On 18.03.2019 22:53, John D Hays - K7VE wrote:
This assumes that /dev/ttyUSB0 is your DVSI USB-3000, if not, change accordingly.

On Mon, Mar 18, 2019 at 12:48 PM John D Hays - K7VE via Groups.Io <john=hays.org@groups.io> wrote:
Try running it without using systemd first.

sudo AMBEserver -i /dev/ttyUSB0 -s 460800 -d

Change the baudrate (-s) if it is not 460800 for your device.

There are also python test scripts you use to test, in the github

Like most Unix/Linux commands there is an -h flag for listing the optional flags



On Mon, Mar 18, 2019 at 12:34 PM Serdar ULUKONAKCI <ta3as@...> wrote:
Hi,
I installed AMBEserver on RPI 3B+. Distro  is Compass Linux and DVSI USB3000 is at USB0
â ambeserver@... - DV3000 Daemon
   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)
   Active: active (running) since Mon 2019-03-18 22:27:36 +03; 11s ago
  Process: 994 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
  Process: 991 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
 Main PID: 997 (AMBEserver)
   CGroup: /system.slice/system-ambeserver.slice/ambeserver@...
           ââ997 /usr/sbin/AMBEserver -p 2460 -i /dev/ttyUSB0 -s 460800

Mar 18 22:27:36 compass systemd[1]: Starting DV3000 Daemon...
Mar 18 22:27:36 compass systemd[1]: Started DV3000 Daemon.
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Starting...
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
After few minutes:
pi@compass:/etc/opendv $ sudo systemctl status ambeserver@...
â ambeserver@... - DV3000 Daemon
   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)
   Active: failed (Result: exit-code) since Mon 2019-03-18 22:28:13 +03; 1min 56s ago
  Process: 997 ExecStart=/usr/sbin/AMBEserver -p ${UDP_PORT} -i /dev/ttyUSB0 $AMBESERVER_FLAGS (code=exited, status=1/FAIL
  Process: 994 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
  Process: 991 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
 Main PID: 997 (code=exited, status=1/FAILURE)

Mar 18 22:27:36 compass systemd[1]: Starting DV3000 Daemon...
Mar 18 22:27:36 compass systemd[1]: Started DV3000 Daemon.
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Starting...
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Main process exited, code=exited, status=1/FAILURE
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Unit entered failed state.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Triggering OnFailure= dependencies.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Failed with result 'exit-code'.
What am I doing wrong?
Any help will be appreciated.

73!
TA3AS
On 17.03.2019 21:20, Serdar ULUKONAKCI wrote:
Hi K7VE,
Thank you very much for your answer.
I have one USB-3000 stick. I'll test it on my RaspberryPi. I'll share the results. I read that compass linux is the preferred dist. for AMBEserver. I'll try to  setup it.
73!
TA3AS
On 17.03.2019 21:05, John D Hays - K7VE wrote:
I have not tested the DVSI USB-3000 stick, they're pretty expensive and I haven't purchased one but I can say that we have used the ThumbDV in applications designed for the DVSI stick and it should work but no guarantee.

On Sun, Mar 17, 2019, 08:28 Serdar ULUKONAKCI <ta3as@...> wrote:
Hi,
I think this can be a wrong group but I could not find any group for my
question.
Can a DVSI's USB-3000 stick work with AMBEserver? Is the DVSI's USB-3000
stick is compatible with AMBEserver software?
Any help will be appreciated.
Best Regards,
TA3AS
Serdar






--


John D. Hays
Edmonds, WA
K7VE

   



--


John D. Hays
Edmonds, WA
K7VE

   


Re: DVSI USB-3000

Serdar ULUKONAKCI
 

Hi John,
Thank you very much for your support.
Yes. USB-3000 is located at USB0
pi@compass:~ $ ls /dev/ttyU*
/dev/ttyUSB0
pi@compass:~ $


and the result after sudo AMBEserver -i /dev/ttyUSB0 -s 460800 -d command.

pi@compass:~ $ sudo AMBEserver -i /dev/ttyUSB0 -s 460800 -d
AMBEserver: Starting...
AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
pi@compass:~ $ AMBEserver: Couldn't find start byte in serial data
AMBEserver: error receiving response to reset
AMBEserver: Could not initialize the DV3K!

73!
Serdar



On 18.03.2019 22:53, John D Hays - K7VE wrote:
This assumes that /dev/ttyUSB0 is your DVSI USB-3000, if not, change accordingly.

On Mon, Mar 18, 2019 at 12:48 PM John D Hays - K7VE via Groups.Io <john=hays.org@groups.io> wrote:
Try running it without using systemd first.

sudo AMBEserver -i /dev/ttyUSB0 -s 460800 -d

Change the baudrate (-s) if it is not 460800 for your device.

There are also python test scripts you use to test, in the github

Like most Unix/Linux commands there is an -h flag for listing the optional flags



On Mon, Mar 18, 2019 at 12:34 PM Serdar ULUKONAKCI <ta3as@...> wrote:
Hi,
I installed AMBEserver on RPI 3B+. Distro  is Compass Linux and DVSI USB3000 is at USB0
â ambeserver@... - DV3000 Daemon
   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)
   Active: active (running) since Mon 2019-03-18 22:27:36 +03; 11s ago
  Process: 994 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
  Process: 991 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
 Main PID: 997 (AMBEserver)
   CGroup: /system.slice/system-ambeserver.slice/ambeserver@...
           ââ997 /usr/sbin/AMBEserver -p 2460 -i /dev/ttyUSB0 -s 460800

Mar 18 22:27:36 compass systemd[1]: Starting DV3000 Daemon...
Mar 18 22:27:36 compass systemd[1]: Started DV3000 Daemon.
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Starting...
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
After few minutes:
pi@compass:/etc/opendv $ sudo systemctl status ambeserver@...
â ambeserver@... - DV3000 Daemon
   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)
   Active: failed (Result: exit-code) since Mon 2019-03-18 22:28:13 +03; 1min 56s ago
  Process: 997 ExecStart=/usr/sbin/AMBEserver -p ${UDP_PORT} -i /dev/ttyUSB0 $AMBESERVER_FLAGS (code=exited, status=1/FAIL
  Process: 994 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
  Process: 991 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
 Main PID: 997 (code=exited, status=1/FAILURE)

Mar 18 22:27:36 compass systemd[1]: Starting DV3000 Daemon...
Mar 18 22:27:36 compass systemd[1]: Started DV3000 Daemon.
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Starting...
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Main process exited, code=exited, status=1/FAILURE
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Unit entered failed state.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Triggering OnFailure= dependencies.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Failed with result 'exit-code'.
What am I doing wrong?
Any help will be appreciated.

73!
TA3AS
On 17.03.2019 21:20, Serdar ULUKONAKCI wrote:
Hi K7VE,
Thank you very much for your answer.
I have one USB-3000 stick. I'll test it on my RaspberryPi. I'll share the results. I read that compass linux is the preferred dist. for AMBEserver. I'll try to  setup it.
73!
TA3AS
On 17.03.2019 21:05, John D Hays - K7VE wrote:
I have not tested the DVSI USB-3000 stick, they're pretty expensive and I haven't purchased one but I can say that we have used the ThumbDV in applications designed for the DVSI stick and it should work but no guarantee.

On Sun, Mar 17, 2019, 08:28 Serdar ULUKONAKCI <ta3as@...> wrote:
Hi,
I think this can be a wrong group but I could not find any group for my
question.
Can a DVSI's USB-3000 stick work with AMBEserver? Is the DVSI's USB-3000
stick is compatible with AMBEserver software?
Any help will be appreciated.
Best Regards,
TA3AS
Serdar






--


John D. Hays
Edmonds, WA
K7VE

   



--


John D. Hays
Edmonds, WA
K7VE

   


Re: DVSI USB-3000

 

This assumes that /dev/ttyUSB0 is your DVSI USB-3000, if not, change accordingly.

On Mon, Mar 18, 2019 at 12:48 PM John D Hays - K7VE via Groups.Io <john=hays.org@groups.io> wrote:
Try running it without using systemd first.

sudo AMBEserver -i /dev/ttyUSB0 -s 460800 -d

Change the baudrate (-s) if it is not 460800 for your device.

There are also python test scripts you use to test, in the github

Like most Unix/Linux commands there is an -h flag for listing the optional flags



On Mon, Mar 18, 2019 at 12:34 PM Serdar ULUKONAKCI <ta3as@...> wrote:
Hi,
I installed AMBEserver on RPI 3B+. Distro  is Compass Linux and DVSI USB3000 is at USB0
â ambeserver@... - DV3000 Daemon
   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)
   Active: active (running) since Mon 2019-03-18 22:27:36 +03; 11s ago
  Process: 994 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
  Process: 991 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
 Main PID: 997 (AMBEserver)
   CGroup: /system.slice/system-ambeserver.slice/ambeserver@...
           ââ997 /usr/sbin/AMBEserver -p 2460 -i /dev/ttyUSB0 -s 460800

Mar 18 22:27:36 compass systemd[1]: Starting DV3000 Daemon...
Mar 18 22:27:36 compass systemd[1]: Started DV3000 Daemon.
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Starting...
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
After few minutes:
pi@compass:/etc/opendv $ sudo systemctl status ambeserver@...
â ambeserver@... - DV3000 Daemon
   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)
   Active: failed (Result: exit-code) since Mon 2019-03-18 22:28:13 +03; 1min 56s ago
  Process: 997 ExecStart=/usr/sbin/AMBEserver -p ${UDP_PORT} -i /dev/ttyUSB0 $AMBESERVER_FLAGS (code=exited, status=1/FAIL
  Process: 994 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
  Process: 991 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
 Main PID: 997 (code=exited, status=1/FAILURE)

Mar 18 22:27:36 compass systemd[1]: Starting DV3000 Daemon...
Mar 18 22:27:36 compass systemd[1]: Started DV3000 Daemon.
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Starting...
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Main process exited, code=exited, status=1/FAILURE
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Unit entered failed state.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Triggering OnFailure= dependencies.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Failed with result 'exit-code'.
What am I doing wrong?
Any help will be appreciated.

73!
TA3AS
On 17.03.2019 21:20, Serdar ULUKONAKCI wrote:
Hi K7VE,
Thank you very much for your answer.
I have one USB-3000 stick. I'll test it on my RaspberryPi. I'll share the results. I read that compass linux is the preferred dist. for AMBEserver. I'll try to  setup it.
73!
TA3AS
On 17.03.2019 21:05, John D Hays - K7VE wrote:
I have not tested the DVSI USB-3000 stick, they're pretty expensive and I haven't purchased one but I can say that we have used the ThumbDV in applications designed for the DVSI stick and it should work but no guarantee.

On Sun, Mar 17, 2019, 08:28 Serdar ULUKONAKCI <ta3as@...> wrote:
Hi,
I think this can be a wrong group but I could not find any group for my
question.
Can a DVSI's USB-3000 stick work with AMBEserver? Is the DVSI's USB-3000
stick is compatible with AMBEserver software?
Any help will be appreciated.
Best Regards,
TA3AS
Serdar






--


John D. Hays
Edmonds, WA
K7VE

   



--


John D. Hays
Edmonds, WA
K7VE

   


Re: DVSI USB-3000

 

Try running it without using systemd first.

sudo AMBEserver -i /dev/ttyUSB0 -s 460800 -d

Change the baudrate (-s) if it is not 460800 for your device.

There are also python test scripts you use to test, in the github

Like most Unix/Linux commands there is an -h flag for listing the optional flags



On Mon, Mar 18, 2019 at 12:34 PM Serdar ULUKONAKCI <ta3as@...> wrote:
Hi,
I installed AMBEserver on RPI 3B+. Distro  is Compass Linux and DVSI USB3000 is at USB0
â ambeserver@... - DV3000 Daemon
   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)
   Active: active (running) since Mon 2019-03-18 22:27:36 +03; 11s ago
  Process: 994 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
  Process: 991 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
 Main PID: 997 (AMBEserver)
   CGroup: /system.slice/system-ambeserver.slice/ambeserver@...
           ââ997 /usr/sbin/AMBEserver -p 2460 -i /dev/ttyUSB0 -s 460800

Mar 18 22:27:36 compass systemd[1]: Starting DV3000 Daemon...
Mar 18 22:27:36 compass systemd[1]: Started DV3000 Daemon.
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Starting...
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
After few minutes:
pi@compass:/etc/opendv $ sudo systemctl status ambeserver@...
â ambeserver@... - DV3000 Daemon
   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)
   Active: failed (Result: exit-code) since Mon 2019-03-18 22:28:13 +03; 1min 56s ago
  Process: 997 ExecStart=/usr/sbin/AMBEserver -p ${UDP_PORT} -i /dev/ttyUSB0 $AMBESERVER_FLAGS (code=exited, status=1/FAIL
  Process: 994 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
  Process: 991 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
 Main PID: 997 (code=exited, status=1/FAILURE)

Mar 18 22:27:36 compass systemd[1]: Starting DV3000 Daemon...
Mar 18 22:27:36 compass systemd[1]: Started DV3000 Daemon.
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Starting...
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Main process exited, code=exited, status=1/FAILURE
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Unit entered failed state.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Triggering OnFailure= dependencies.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Failed with result 'exit-code'.
What am I doing wrong?
Any help will be appreciated.

73!
TA3AS
On 17.03.2019 21:20, Serdar ULUKONAKCI wrote:
Hi K7VE,
Thank you very much for your answer.
I have one USB-3000 stick. I'll test it on my RaspberryPi. I'll share the results. I read that compass linux is the preferred dist. for AMBEserver. I'll try to  setup it.
73!
TA3AS
On 17.03.2019 21:05, John D Hays - K7VE wrote:
I have not tested the DVSI USB-3000 stick, they're pretty expensive and I haven't purchased one but I can say that we have used the ThumbDV in applications designed for the DVSI stick and it should work but no guarantee.

On Sun, Mar 17, 2019, 08:28 Serdar ULUKONAKCI <ta3as@...> wrote:
Hi,
I think this can be a wrong group but I could not find any group for my
question.
Can a DVSI's USB-3000 stick work with AMBEserver? Is the DVSI's USB-3000
stick is compatible with AMBEserver software?
Any help will be appreciated.
Best Regards,
TA3AS
Serdar






--


John D. Hays
Edmonds, WA
K7VE

   


Re: DVSI USB-3000

Serdar ULUKONAKCI
 

Hi,
I installed AMBEserver on RPI 3B+. Distro  is Compass Linux and DVSI USB3000 is at USB0
â ambeserver@... - DV3000 Daemon
   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)
   Active: active (running) since Mon 2019-03-18 22:27:36 +03; 11s ago
  Process: 994 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
  Process: 991 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
 Main PID: 997 (AMBEserver)
   CGroup: /system.slice/system-ambeserver.slice/ambeserver@...
           ââ997 /usr/sbin/AMBEserver -p 2460 -i /dev/ttyUSB0 -s 460800

Mar 18 22:27:36 compass systemd[1]: Starting DV3000 Daemon...
Mar 18 22:27:36 compass systemd[1]: Started DV3000 Daemon.
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Starting...
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
After few minutes:
pi@compass:/etc/opendv $ sudo systemctl status ambeserver@...
â ambeserver@... - DV3000 Daemon
   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)
   Active: failed (Result: exit-code) since Mon 2019-03-18 22:28:13 +03; 1min 56s ago
  Process: 997 ExecStart=/usr/sbin/AMBEserver -p ${UDP_PORT} -i /dev/ttyUSB0 $AMBESERVER_FLAGS (code=exited, status=1/FAIL
  Process: 994 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
  Process: 991 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, status=0/SUCCESS)
 Main PID: 997 (code=exited, status=1/FAILURE)

Mar 18 22:27:36 compass systemd[1]: Starting DV3000 Daemon...
Mar 18 22:27:36 compass systemd[1]: Started DV3000 Daemon.
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Starting...
Mar 18 22:27:36 compass AMBEserver[997]: AMBEserver: Opened serial port /dev/ttyUSB0 at 460800 bps.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Main process exited, code=exited, status=1/FAILURE
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Unit entered failed state.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Triggering OnFailure= dependencies.
Mar 18 22:28:13 compass systemd[1]: ambeserver@...: Failed with result 'exit-code'.
What am I doing wrong?
Any help will be appreciated.

73!
TA3AS

On 17.03.2019 21:20, Serdar ULUKONAKCI wrote:
Hi K7VE,
Thank you very much for your answer.
I have one USB-3000 stick. I'll test it on my RaspberryPi. I'll share the results. I read that compass linux is the preferred dist. for AMBEserver. I'll try to  setup it.
73!
TA3AS
On 17.03.2019 21:05, John D Hays - K7VE wrote:
I have not tested the DVSI USB-3000 stick, they're pretty expensive and I haven't purchased one but I can say that we have used the ThumbDV in applications designed for the DVSI stick and it should work but no guarantee.

On Sun, Mar 17, 2019, 08:28 Serdar ULUKONAKCI <ta3as@...> wrote:
Hi,
I think this can be a wrong group but I could not find any group for my
question.
Can a DVSI's USB-3000 stick work with AMBEserver? Is the DVSI's USB-3000
stick is compatible with AMBEserver software?
Any help will be appreciated.
Best Regards,
TA3AS
Serdar





Re: DVSI USB-3000

Serdar ULUKONAKCI
 

Hi K7VE,
Thank you very much for your answer.
I have one USB-3000 stick. I'll test it on my RaspberryPi. I'll share the results. I read that compass linux is the preferred dist. for AMBEserver. I'll try to  setup it.
73!
TA3AS

On 17.03.2019 21:05, John D Hays - K7VE wrote:
I have not tested the DVSI USB-3000 stick, they're pretty expensive and I haven't purchased one but I can say that we have used the ThumbDV in applications designed for the DVSI stick and it should work but no guarantee.

On Sun, Mar 17, 2019, 08:28 Serdar ULUKONAKCI <ta3as@...> wrote:
Hi,
I think this can be a wrong group but I could not find any group for my
question.
Can a DVSI's USB-3000 stick work with AMBEserver? Is the DVSI's USB-3000
stick is compatible with AMBEserver software?
Any help will be appreciated.
Best Regards,
TA3AS
Serdar





Re: DVSI USB-3000

 

I have not tested the DVSI USB-3000 stick, they're pretty expensive and I haven't purchased one but I can say that we have used the ThumbDV in applications designed for the DVSI stick and it should work but no guarantee.


On Sun, Mar 17, 2019, 08:28 Serdar ULUKONAKCI <ta3as@...> wrote:
Hi,
I think this can be a wrong group but I could not find any group for my
question.
Can a DVSI's USB-3000 stick work with AMBEserver? Is the DVSI's USB-3000
stick is compatible with AMBEserver software?
Any help will be appreciated.
Best Regards,
TA3AS
Serdar





Re: ambeserver failing?

Mike Besemer - WM4B
 

I did: 

 

 

$ sudo nano /boot/config.txt

init_uart_clock=3686400

 

 

$ sudo nano /etc/inittab

T0:23:respawn:/sbin/getty -L ttyAMA0 115200 vt100

with:(or delete the line entirely)

#T0:23:respawn:/sbin/getty -L ttyAMA0 115200 vt100

(Actually, /etc/inittab does not even exist)

 

 

$ sudo nano /boot/cmdline.txt

dwc_otg.lpm_enable=0 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait

 

What did I miss?

 

Mike

WM4B

 

From: ambe@nw-digital-radio.groups.io [mailto:ambe@nw-digital-radio.groups.io] On Behalf Of Ernest Pratt
Sent: Sunday, March 17, 2019 3:43 AM
To: ambe@nw-digital-radio.groups.io
Subject: Re: [ambe] ambeserver failing?

 

On Sun, Mar 17, 2019 at 03:52 AM, Mike Besemer wrote:

Well, that’s what I thought, but considering that exactly zero things have worked correctly since I started this project, I thought I’d confirm.

 

So: 

pi@compass:/usr/sbin $ sudo ./AMBEserver  -d -i /dev/ttyAMA0

AMBEserver: Starting...

AMBEserver: Opened serial port /dev/ttyAMA0 at 230400 bps.

pi@compass:/usr/sbin $ AMBEserver: Couldn't find start byte in serial data

AMBEserver: error receiving response to reset

AMBEserver: Could not initialize the DV3K!

 

Mike

WM4B

Your DV3K is not  being seen by the operating system, I had to edit a startup file on the pi for it to work. Had the same problem.

 


DVSI USB-3000

Serdar ULUKONAKCI
 

Hi,
I think this can be a wrong group but I could not find any group for my question.
Can a DVSI's USB-3000 stick work with AMBEserver? Is the DVSI's USB-3000 stick is compatible with AMBEserver software?
Any help will be appreciated.
Best Regards,
TA3AS
Serdar


Re: ambeserver failing?

 

On Sun, Mar 17, 2019 at 03:52 AM, Mike Besemer wrote:

Well, that’s what I thought, but considering that exactly zero things have worked correctly since I started this project, I thought I’d confirm.

 

So: 

pi@compass:/usr/sbin $ sudo ./AMBEserver  -d -i /dev/ttyAMA0

AMBEserver: Starting...

AMBEserver: Opened serial port /dev/ttyAMA0 at 230400 bps.

pi@compass:/usr/sbin $ AMBEserver: Couldn't find start byte in serial data

AMBEserver: error receiving response to reset

AMBEserver: Could not initialize the DV3K!

 

Mike

WM4B

Your DV3K is not  being seen by the operating system, I had to edit a startup file on the pi for it to work. Had the same problem.

 


Re: ambeserver failing?

Mike Besemer - WM4B
 

Well, that’s what I thought, but considering that exactly zero things have worked correctly since I started this project, I thought I’d confirm.

 

So: 

pi@compass:/usr/sbin $ sudo ./AMBEserver  -d -i /dev/ttyAMA0

AMBEserver: Starting...

AMBEserver: Opened serial port /dev/ttyAMA0 at 230400 bps.

pi@compass:/usr/sbin $ AMBEserver: Couldn't find start byte in serial data

AMBEserver: error receiving response to reset

AMBEserver: Could not initialize the DV3K!

 

Mike

WM4B

 

From: ambe@nw-digital-radio.groups.io [mailto:ambe@nw-digital-radio.groups.io] On Behalf Of John D Hays - K7VE
Sent: Saturday, March 16, 2019 6:31 PM
To: ambe@nw-digital-radio.groups.io
Subject: Re: [ambe] ambeserver failing?

 

Same way as your email of the 12th

 

Mike Besemer mwbesemer@... via groups.io 

Mar 12, 2019, 5:11 PM (4 days ago)

to ambe

pi@raspberrypi:/usr/sbin $ sudo AMBEserver -i /dev/ttyAMA0

AMBEserver: Starting...

AMBEserver: Opened serial port /dev/ttyAMA0 at 230400 bps.

 

Leave running in one window and then try your other programs.

 

--

 


John D. Hays
Edmonds, WA

K7VE

 

   

 


Re: ambeserver failing?

 

Same way as your email of the 12th

Mike Besemer mwbesemer@... via groups.io 

Mar 12, 2019, 5:11 PM (4 days ago)
to ambe

pi@raspberrypi:/usr/sbin $ sudo AMBEserver -i /dev/ttyAMA0

AMBEserver: Starting...

AMBEserver: Opened serial port /dev/ttyAMA0 at 230400 bps.


Leave running in one window and then try your other programs.

--


John D. Hays
Edmonds, WA
K7VE

   


Re: ambeserver failing?

Mike Besemer - WM4B
 

How do I do that?

 

 

 

From: ambe@nw-digital-radio.groups.io [mailto:ambe@nw-digital-radio.groups.io] On Behalf Of John D Hays - K7VE
Sent: Saturday, March 16, 2019 5:33 PM
To: ambe@nw-digital-radio.groups.io
Subject: Re: [ambe] ambeserver failing?

 

Try starting it on the command line, not using the systemctl / service scripts and see if it stays up.

 

On Sat, Mar 16, 2019 at 2:01 PM Mike Besemer <mwbesemer@...> wrote:

Still struggling.  Currently getting an ‘Unable to Transmit’ error from dummyrepeater. 

I went back and looked at ambeserver.  As you can see below, I start ambeserver and immediately check the status.  It appears to start properly.  Then I check the status again less than a minute later and see a ‘failed’ message.  I don’t know if this is what’s causing dummyrepeater to throw the error code, but I don’t think this is right.

Mike

WM4B

pi@compass:~ $ sudo systemctl start ambeserver@...

pi@compass:~ $ sudo systemctl status ambeserver@...

● ambeserver@... - DV3000 Daemon

   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)

   Active: active (running) since Sat 2019-03-16 16:55:45 EDT; 12s ago

  Process: 2201 ExecStartPre=/bin/chmod 0660 /dev/ttyAMA0 (code=exited, status=0/SUCCESS)

  Process: 2198 ExecStartPre=/bin/chgrp dialout /dev/ttyAMA0 (code=exited, status=0/SUCCESS)

 Main PID: 2204 (AMBEserver)

   CGroup: /system.slice/system-ambeserver.slice/ambeserver@...

           └─2204 /usr/sbin/AMBEserver -p 2460 -i /dev/ttyAMA0 -r

Mar 16 16:55:45 compass systemd[1]: Starting DV3000 Daemon...

Mar 16 16:55:45 compass systemd[1]: Started DV3000 Daemon.

Mar 16 16:55:45 compass AMBEserver[2204]: AMBEserver: Starting...

Mar 16 16:55:45 compass AMBEserver[2204]: AMBEserver: Opened serial port /dev/ttyAMA0 at 230400 bps.

pi@compass:~ $ sudo systemctl status ambeserver@...

● ambeserver@... - DV3000 Daemon

   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)

   Active: failed (Result: exit-code) since Sat 2019-03-16 16:56:22 EDT; 22s ago

  Process: 2204 ExecStart=/usr/sbin/AMBEserver -p ${UDP_PORT} -i /dev/ttyAMA0 $AMBESERVER_FLAGS (code=exited, status=1/FAILURE)

  Process: 2201 ExecStartPre=/bin/chmod 0660 /dev/ttyAMA0 (code=exited, status=0/SUCCESS)

  Process: 2198 ExecStartPre=/bin/chgrp dialout /dev/ttyAMA0 (code=exited, status=0/SUCCESS)

 Main PID: 2204 (code=exited, status=1/FAILURE)

Mar 16 16:55:45 compass systemd[1]: Starting DV3000 Daemon...

Mar 16 16:55:45 compass systemd[1]: Started DV3000 Daemon.

Mar 16 16:55:45 compass AMBEserver[2204]: AMBEserver: Starting...

Mar 16 16:55:45 compass AMBEserver[2204]: AMBEserver: Opened serial port /dev/ttyAMA0 at 230400 bps.

Mar 16 16:56:22 compass systemd[1]: ambeserver@...: Main process exited, code=exited, status=1/FAILURE

Mar 16 16:56:22 compass systemd[1]: ambeserver@...: Unit entered failed state.

Mar 16 16:56:22 compass systemd[1]: ambeserver@...: Triggering OnFailure= dependencies.

Mar 16 16:56:22 compass systemd[1]: ambeserver@...: Failed with result 'exit-code'.

pi@compass:~ $

 


 

--

 


John D. Hays
Edmonds, WA

K7VE

 

   

 


Re: ambeserver failing?

 

Try starting it on the command line, not using the systemctl / service scripts and see if it stays up.

On Sat, Mar 16, 2019 at 2:01 PM Mike Besemer <mwbesemer@...> wrote:

Still struggling.  Currently getting an Unable to Transmit error from dummyrepeater. 

I went back and looked at ambeserver.  As you can see below, I start ambeserver and immediately check the status.  It appears to start properly.  Then I check the status again less than a minute later and see a failed message.  I dont know if this is what’s causing dummyrepeater to throw the error code, but I dont think this is right.

Mike

WM4B

pi@compass:~ $ sudo systemctl start ambeserver@...

pi@compass:~ $ sudo systemctl status ambeserver@...

● ambeserver@... - DV3000 Daemon

   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)

   Active: active (running) since Sat 2019-03-16 16:55:45 EDT; 12s ago

  Process: 2201 ExecStartPre=/bin/chmod 0660 /dev/ttyAMA0 (code=exited, status=0/SUCCESS)

  Process: 2198 ExecStartPre=/bin/chgrp dialout /dev/ttyAMA0 (code=exited, status=0/SUCCESS)

 Main PID: 2204 (AMBEserver)

   CGroup: /system.slice/system-ambeserver.slice/ambeserver@...

           └─2204 /usr/sbin/AMBEserver -p 2460 -i /dev/ttyAMA0 -r

Mar 16 16:55:45 compass systemd[1]: Starting DV3000 Daemon...

Mar 16 16:55:45 compass systemd[1]: Started DV3000 Daemon.

Mar 16 16:55:45 compass AMBEserver[2204]: AMBEserver: Starting...

Mar 16 16:55:45 compass AMBEserver[2204]: AMBEserver: Opened serial port /dev/ttyAMA0 at 230400 bps.

pi@compass:~ $ sudo systemctl status ambeserver@...

● ambeserver@... - DV3000 Daemon

   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)

   Active: failed (Result: exit-code) since Sat 2019-03-16 16:56:22 EDT; 22s ago

  Process: 2204 ExecStart=/usr/sbin/AMBEserver -p ${UDP_PORT} -i /dev/ttyAMA0 $AMBESERVER_FLAGS (code=exited, status=1/FAILURE)

  Process: 2201 ExecStartPre=/bin/chmod 0660 /dev/ttyAMA0 (code=exited, status=0/SUCCESS)

  Process: 2198 ExecStartPre=/bin/chgrp dialout /dev/ttyAMA0 (code=exited, status=0/SUCCESS)

 Main PID: 2204 (code=exited, status=1/FAILURE)

Mar 16 16:55:45 compass systemd[1]: Starting DV3000 Daemon...

Mar 16 16:55:45 compass systemd[1]: Started DV3000 Daemon.

Mar 16 16:55:45 compass AMBEserver[2204]: AMBEserver: Starting...

Mar 16 16:55:45 compass AMBEserver[2204]: AMBEserver: Opened serial port /dev/ttyAMA0 at 230400 bps.

Mar 16 16:56:22 compass systemd[1]: ambeserver@...: Main process exited, code=exited, status=1/FAILURE

Mar 16 16:56:22 compass systemd[1]: ambeserver@...: Unit entered failed state.

Mar 16 16:56:22 compass systemd[1]: ambeserver@...: Triggering OnFailure= dependencies.

Mar 16 16:56:22 compass systemd[1]: ambeserver@...: Failed with result 'exit-code'.

pi@compass:~ $




--


John D. Hays
Edmonds, WA
K7VE

   


ambeserver failing?

Mike Besemer - WM4B
 

Still struggling.  Currently getting an Unable to Transmit error from dummyrepeater. 

I went back and looked at ambeserver.  As you can see below, I start ambeserver and immediately check the status.  It appears to start properly.  Then I check the status again less than a minute later and see a failed message.  I dont know if this is what’s causing dummyrepeater to throw the error code, but I dont think this is right.

Mike

WM4B

pi@compass:~ $ sudo systemctl start ambeserver@...

pi@compass:~ $ sudo systemctl status ambeserver@...

● ambeserver@... - DV3000 Daemon

   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)

   Active: active (running) since Sat 2019-03-16 16:55:45 EDT; 12s ago

  Process: 2201 ExecStartPre=/bin/chmod 0660 /dev/ttyAMA0 (code=exited, status=0/SUCCESS)

  Process: 2198 ExecStartPre=/bin/chgrp dialout /dev/ttyAMA0 (code=exited, status=0/SUCCESS)

 Main PID: 2204 (AMBEserver)

   CGroup: /system.slice/system-ambeserver.slice/ambeserver@...

           └─2204 /usr/sbin/AMBEserver -p 2460 -i /dev/ttyAMA0 -r

Mar 16 16:55:45 compass systemd[1]: Starting DV3000 Daemon...

Mar 16 16:55:45 compass systemd[1]: Started DV3000 Daemon.

Mar 16 16:55:45 compass AMBEserver[2204]: AMBEserver: Starting...

Mar 16 16:55:45 compass AMBEserver[2204]: AMBEserver: Opened serial port /dev/ttyAMA0 at 230400 bps.

pi@compass:~ $ sudo systemctl status ambeserver@...

● ambeserver@... - DV3000 Daemon

   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor preset: enabled)

   Active: failed (Result: exit-code) since Sat 2019-03-16 16:56:22 EDT; 22s ago

  Process: 2204 ExecStart=/usr/sbin/AMBEserver -p ${UDP_PORT} -i /dev/ttyAMA0 $AMBESERVER_FLAGS (code=exited, status=1/FAILURE)

  Process: 2201 ExecStartPre=/bin/chmod 0660 /dev/ttyAMA0 (code=exited, status=0/SUCCESS)

  Process: 2198 ExecStartPre=/bin/chgrp dialout /dev/ttyAMA0 (code=exited, status=0/SUCCESS)

 Main PID: 2204 (code=exited, status=1/FAILURE)

Mar 16 16:55:45 compass systemd[1]: Starting DV3000 Daemon...

Mar 16 16:55:45 compass systemd[1]: Started DV3000 Daemon.

Mar 16 16:55:45 compass AMBEserver[2204]: AMBEserver: Starting...

Mar 16 16:55:45 compass AMBEserver[2204]: AMBEserver: Opened serial port /dev/ttyAMA0 at 230400 bps.

Mar 16 16:56:22 compass systemd[1]: ambeserver@...: Main process exited, code=exited, status=1/FAILURE

Mar 16 16:56:22 compass systemd[1]: ambeserver@...: Unit entered failed state.

Mar 16 16:56:22 compass systemd[1]: ambeserver@...: Triggering OnFailure= dependencies.

Mar 16 16:56:22 compass systemd[1]: ambeserver@...: Failed with result 'exit-code'.

pi@compass:~ $



Re: How to add the Compass Linux repository to Debian ?

Stefsan
 

Hi its easy to compile only one line

before get it from github, unzip it and configure the c code by eding 2 lines  , make and make install and if neccesarry add a scritp in autostart or start service with init.d

here manual in german,translate to google if you want

_______________________________

4 AMBE Server installieren


laden Sie den Source Code aus github herunter.

Terminal Console offnen und

cd /tmp eingeben


(Sie sind nun im tmp Verzeichniss)

Nun Daten laden mit

sudo wget https://github.com/marrold/AMBEServer/archive/master.zip


Wenn fertig sind diese nun im tmp Verzeciniss und müssen entpackt werden mi

sudo unzip master.zip


Ein Unterverzeichniss AMBEServer-master ist nun entstanden, diese beinhaltet die zu compilierenden Komponenten

Nun im Terminal die Datei AMBEserver.c mit sudo nano AMBEserver.c öffnen

DV30 Stick Baudrate 460800Bd

alter ThumbDV 230600 Bd

AMBE3000 Board für MyDV  230600 Bd


Hier habe ich die Standard-Baudrate eingestellt, mit der der Dongle arbeitet. Ich habe das gemacht, weil die neuen Dongles alle bei 460800 Baud laufen und nicht bei 230400.

 Suche in AMBEserver.c nach
# Define default_baud 230400
und ändern Sie die 230400 in 460800
so wird es zu:
# Define default_baud 460800
Sichere diese Datei
Wenn die Zeile geändert ist mit strg O speichern.
Nun muss kompiliert werden
sudo make
danach mit 
sudo make install.
Der Programmaufruf kann nun mit AMBEserver -x  getestet werden.

Ein Start Script kann mit nano im Verzeichniss .config/autostart angelegt werden.
[Desktop Entry]
GenericName=AMBEServer
Name=AMBEServer
Comment=DV30 USB AMBEServer
Exec=sh -c "cd /usr/bin ; ./AMBEserver -x"
Terminal=false
;Terminal=true
Type=Application
Categories=Network;WebBrowser;
;Icon=/home/pi/Downloads/DV4Mini_Raspi/dv4.ico
Icon=/home/pi/Downloads/ambe.jpeg

Dann startet der AMBE Server automatisch!!! beim Neustart

Am 15.03.19 um 15:50 schrieb John Anderson via Groups.Io:

I want to add the Compass Linux repository to Debian, what file do i edit to do this ?

721 - 740 of 1592