Date   
How to Add XLX 299 R to Host files of BluDV for Android?

Dev 9Y4DG
 

Good day,
                 Thank you for taking the time to read this message.

Is there any way I can add either XLX 299 R. XRF 299 R or DCS 299 R to the host files of BlueDV for Android??

Or is there any way of downloading and updating the host files to include any or all of the above reflectors??

Thank you again for your responses and guidance....73 Dev, 9Y4DG

--


“Your chances of success in any undertaking can
always be measured by your belief in yourself"
       ~Robert Collier~.

The pessimist complains about the wind.
The optimist expects it to change.
The leader adjusts the sails.

                 ~John Maxwell~

Teamwork is the ability to work together toward a common vision.
The ability to direct individual accomplishment toward organizational objectives.
It is the fuel that allows common people to attain uncommon results.
      ~ Anonymous~

We believe that:

"We make a living by what we get,
We make a life by what we give!"
          ~Winston Churchill~

Re: How to Add XLX 299 R to Host files of BluDV for Android?

 

Take a look at this link: http://www.pa7lim.nl/dstar-hosts-files/

Greets and 73,

David PA7LIM

Op 12/02/2019 om 14:34 schreef Dev Gosine:

Good day,
                 Thank you for taking the time to read this message.

Is there any way I can add either XLX 299 R. XRF 299 R or DCS 299 R to the host files of BlueDV for Android??

Or is there any way of downloading and updating the host files to include any or all of the above reflectors??

Thank you again for your responses and guidance....73 Dev, 9Y4DG

--


“Your chances of success in any undertaking can
always be measured by your belief in yourself"
       ~Robert Collier~.

The pessimist complains about the wind.
The optimist expects it to change.
The leader adjusts the sails.

                 ~John Maxwell~

Teamwork is the ability to work together toward a common vision.
The ability to direct individual accomplishment toward organizational objectives.
It is the fuel that allows common people to attain uncommon results.
      ~ Anonymous~

We believe that:

"We make a living by what we get,
We make a life by what we give!"
          ~Winston Churchill~

Re: How to Add XLX 299 R to Host files of BluDV for Android?

Dev 9Y4DG
 

Thank you very much David...73 Dev, 9Y4DG


On Tue, 12 Feb 2019 at 09:44, David PA7LIM <info@...> wrote:

Take a look at this link: http://www.pa7lim.nl/dstar-hosts-files/

Greets and 73,

David PA7LIM

Op 12/02/2019 om 14:34 schreef Dev Gosine:
Good day,
                 Thank you for taking the time to read this message.

Is there any way I can add either XLX 299 R. XRF 299 R or DCS 299 R to the host files of BlueDV for Android??

Or is there any way of downloading and updating the host files to include any or all of the above reflectors??

Thank you again for your responses and guidance....73 Dev, 9Y4DG

--


“Your chances of success in any undertaking can
always be measured by your belief in yourself"
       ~Robert Collier~.

The pessimist complains about the wind.
The optimist expects it to change.
The leader adjusts the sails.

                 ~John Maxwell~

Teamwork is the ability to work together toward a common vision.
The ability to direct individual accomplishment toward organizational objectives.
It is the fuel that allows common people to attain uncommon results.
      ~ Anonymous~

We believe that:

"We make a living by what we get,
We make a life by what we give!"
          ~Winston Churchill~



--


“Your chances of success in any undertaking can
always be measured by your belief in yourself"
       ~Robert Collier~.

The pessimist complains about the wind.
The optimist expects it to change.
The leader adjusts the sails.

                 ~John Maxwell~

Teamwork is the ability to work together toward a common vision.
The ability to direct individual accomplishment toward organizational objectives.
It is the fuel that allows common people to attain uncommon results.
      ~ Anonymous~

We believe that:

"We make a living by what we get,
We make a life by what we give!"
          ~Winston Churchill~

BlueDV Windows crashes with .NET error

Jim - K6JM
 

I'm helping a ham use BlueDV Windows with his ThumbDV on a new-to-him Windows 7 laptop.  I used Teamviewer remotely to update .NET to version 4.7 and to install the latest Beta version of BlueDV Windows.  When I launch it, it crashes with a .NET error that PortName must not be empty.  He is running Win7 64 bit.

I am sure this is a problem with this PC, not BlueDV.  Has anyone else seen this error?

     Jim - K6JM  

Re: Can 6 Digit DMR IDs work with BlueDV & AMBE Servers?? #dmrid, #ambe, # amberserver

Jason Kingsbury
 

Not sure if this will work, but have you tried to put a 0 (zero) in front of the six digit ID when configuring it on BlueDV? 


On Feb 8, 2019, at 1:56 PM, Dev Gosine <dgosine@...> wrote:

Good day,
                  Thank you for taking the time to read this message and also for your kind contribution to the thread.

Here are the facts.

1. I have 5 AMBE Servers.
2. I have 2 DMR IDs
3. BlueDV (Android) does not support adding an additional 2 digits to the end of the DMR ID as the DMR ID input field allows only 7 digits.
4. I have applied for additional DMR IDs, but was given five 6 digit repeater IDs.
5. This initially sounded like the perfect solution since I have 5 AMBE Servers and got 5 DMR IDs.
6. The problem is that the 6 digit DMR ID is not seen on Brandmeister's Hoseline when I transmit. This means I have absolutely no transmission being monitored on hoseline if I were to transmit.

Can anyone tell me what I'm doing wrong and possibly lead me in the correct direction.

I thank you again for all your contributions.....73 Dev, 9Y4DG
 

 

Re: Can 6 Digit DMR IDs work with BlueDV & AMBE Servers?? #dmrid, #ambe, # amberserver

Dave Amos <damos54@...>
 

Hi

I, too, have experienced connection problems running BlueDV/ThumbDV.  Make sure your thumb drive comm port is selected under "General" and "AMBE" boxes in the setup window under the "FILE" menu selection.  My ThumbDV drive is on COM36 on my computer (I do a lot of work with USB connected devices so I have some that are clear up in the high 60's).

I do not have a zero in front of my ID number and have had no issues with that.

by the way, I have not received an answer to my question regarding the Wednesday evening Not a Net Gathering.  Is it possible to connect to that net using BlueDV and if so, what is the talk group number I need to use.  Can I access via BM or do I have to select a DMR+ server connection?

73,

Dave, WB7DFV


On 2/8/2019 1:19 PM, Jason Kingsbury wrote:
Not sure if this will work, but have you tried to put a 0 (zero) in front of the six digit ID when configuring it on BlueDV? 


On Feb 8, 2019, at 1:56 PM, Dev Gosine <dgosine@...> wrote:

Good day,
                  Thank you for taking the time to read this message and also for your kind contribution to the thread.

Here are the facts.

1. I have 5 AMBE Servers.
2. I have 2 DMR IDs
3. BlueDV (Android) does not support adding an additional 2 digits to the end of the DMR ID as the DMR ID input field allows only 7 digits.
4. I have applied for additional DMR IDs, but was given five 6 digit repeater IDs.
5. This initially sounded like the perfect solution since I have 5 AMBE Servers and got 5 DMR IDs.
6. The problem is that the 6 digit DMR ID is not seen on Brandmeister's Hoseline when I transmit. This means I have absolutely no transmission being monitored on hoseline if I were to transmit.

Can anyone tell me what I'm doing wrong and possibly lead me in the correct direction.

I thank you again for all your contributions.....73 Dev, 9Y4DG
 

 

Re: Can 6 Digit DMR IDs work with BlueDV & AMBE Servers?? #dmrid, #ambe, # amberserver

J G Shaw
 

In the past, I have found that Wed Not a Net Gathering on BM TG 31771. 

But, have not listened in recently – hope it hasn’t changed.

 

From: ambe@nw-digital-radio.groups.io [mailto:ambe@nw-digital-radio.groups.io] On Behalf Of Dave Amos
Sent: Friday, February 22, 2019 7:42 AM
To: ambe@nw-digital-radio.groups.io
Subject: Re: [ambe] Can 6 Digit DMR IDs work with BlueDV & AMBE Servers?? #dmrid, #ambe, # amberserver

 

Hi

I, too, have experienced connection problems running BlueDV/ThumbDV.  Make sure your thumb drive comm port is selected under "General" and "AMBE" boxes in the setup window under the "FILE" menu selection.  My ThumbDV drive is on COM36 on my computer (I do a lot of work with USB connected devices so I have some that are clear up in the high 60's).

I do not have a zero in front of my ID number and have had no issues with that.

by the way, I have not received an answer to my question regarding the Wednesday evening Not a Net Gathering.  Is it possible to connect to that net using BlueDV and if so, what is the talk group number I need to use.  Can I access via BM or do I have to select a DMR+ server connection?

73,

Dave, WB7DFV

 

On 2/8/2019 1:19 PM, Jason Kingsbury wrote:

Not sure if this will work, but have you tried to put a 0 (zero) in front of the six digit ID when configuring it on BlueDV? 


On Feb 8, 2019, at 1:56 PM, Dev Gosine <dgosine@...> wrote:

Good day,
                  Thank you for taking the time to read this message and also for your kind contribution to the thread.

Here are the facts.

1. I have 5 AMBE Servers.
2. I have 2 DMR IDs
3. BlueDV (Android) does not support adding an additional 2 digits to the end of the DMR ID as the DMR ID input field allows only 7 digits.
4. I have applied for additional DMR IDs, but was given five 6 digit repeater IDs.
5. This initially sounded like the perfect solution since I have 5 AMBE Servers and got 5 DMR IDs.
6. The problem is that the 6 digit DMR ID is not seen on Brandmeister's Hoseline when I transmit. This means I have absolutely no transmission being monitored on hoseline if I were to transmit.

Can anyone tell me what I'm doing wrong and possibly lead me in the correct direction.

I thank you again for all your contributions.....73 Dev, 9Y4DG
 

 

Re: Can 6 Digit DMR IDs work with BlueDV & AMBE Servers?? #dmrid, #ambe, # amberserver

Dave Amos <damos54@...>
 

Thanks WA6PX,

I will give that a try next Wednesday evening Brandmeister talk group 31771.

73,

Dave, WB7DFV

On 2/22/2019 8:45 AM, J G Shaw wrote:

In the past, I have found that Wed Not a Net Gathering on BM TG 31771. 

But, have not listened in recently – hope it hasn’t changed.

 

From: ambe@nw-digital-radio.groups.io [mailto:ambe@nw-digital-radio.groups.io] On Behalf Of Dave Amos
Sent: Friday, February 22, 2019 7:42 AM
To: ambe@nw-digital-radio.groups.io
Subject: Re: [ambe] Can 6 Digit DMR IDs work with BlueDV & AMBE Servers?? #dmrid, #ambe, # amberserver

 

Hi

I, too, have experienced connection problems running BlueDV/ThumbDV.  Make sure your thumb drive comm port is selected under "General" and "AMBE" boxes in the setup window under the "FILE" menu selection.  My ThumbDV drive is on COM36 on my computer (I do a lot of work with USB connected devices so I have some that are clear up in the high 60's).

I do not have a zero in front of my ID number and have had no issues with that.

by the way, I have not received an answer to my question regarding the Wednesday evening Not a Net Gathering.  Is it possible to connect to that net using BlueDV and if so, what is the talk group number I need to use.  Can I access via BM or do I have to select a DMR+ server connection?

73,

Dave, WB7DFV

 

On 2/8/2019 1:19 PM, Jason Kingsbury wrote:

Not sure if this will work, but have you tried to put a 0 (zero) in front of the six digit ID when configuring it on BlueDV? 


On Feb 8, 2019, at 1:56 PM, Dev Gosine <dgosine@...> wrote:

Good day,
                  Thank you for taking the time to read this message and also for your kind contribution to the thread.

Here are the facts.

1. I have 5 AMBE Servers.
2. I have 2 DMR IDs
3. BlueDV (Android) does not support adding an additional 2 digits to the end of the DMR ID as the DMR ID input field allows only 7 digits.
4. I have applied for additional DMR IDs, but was given five 6 digit repeater IDs.
5. This initially sounded like the perfect solution since I have 5 AMBE Servers and got 5 DMR IDs.
6. The problem is that the 6 digit DMR ID is not seen on Brandmeister's Hoseline when I transmit. This means I have absolutely no transmission being monitored on hoseline if I were to transmit.

Can anyone tell me what I'm doing wrong and possibly lead me in the correct direction.

I thank you again for all your contributions.....73 Dev, 9Y4DG
 

 

AMBEServer DVStick 30 Compass Raspberry Pi #ambeserver

Al Mesa
 

Hello,
I am having the following issue:
CONDITIONS: Raspberry Pi 3B+ Compass Linux, DVStick 30.
ISSUE After install without problems the AMBEserver per instructions and after start the AMBEServer service, a few seconds after the AMBEServer services stop and failed.
Please see the terminal detail:
 

^Xroot@compass:~# systemctl start ambeserver@...

root@compass:~# systemctl status ambeserver@...

● ambeserver@... - DV3000 Daemon

   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor pres

   Active: active (running) since Thu 2019-02-28 11:14:00 EST; 31s ago

  Process: 20143 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=

  Process: 20142 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, stat

 Main PID: 20148 (AMBEserver)

   CGroup: /system.slice/system-ambeserver.slice/ambeserver@...

           └─20148 /usr/sbin/AMBEserver -p 2460 -i /dev/ttyUSB0

 

Feb 28 11:14:00 compass systemd[1]: Starting DV3000 Daemon...

Feb 28 11:14:00 compass systemd[1]: Started DV3000 Daemon.

Feb 28 11:14:00 compass AMBEserver[20148]: AMBEserver: Starting...

Feb 28 11:14:00 compass AMBEserver[20148]: AMBEserver: Opened serial port /dev/t

 

/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

 

pi@compass:~ $ sudo systemctl status ambeserver@...

● ambeserver@... - DV3000 Daemon

   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor pres

   Active: failed (Result: exit-code) since Thu 2019-02-28 11:14:36 EST; 1min 27

  Process: 20148 ExecStart=/usr/sbin/AMBEserver -p ${UDP_PORT} -i /dev/ttyUSB0 $

  Process: 20143 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=

  Process: 20142 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, stat

 Main PID: 20148 (code=exited, status=1/FAILURE)

 

Feb 28 11:14:00 compass systemd[1]: Starting DV3000 Daemon...

Feb 28 11:14:00 compass systemd[1]: Started DV3000 Daemon.

Feb 28 11:14:00 compass AMBEserver[20148]: AMBEserver: Starting...

Feb 28 11:14:00 compass AMBEserver[20148]: AMBEserver: Opened serial port /dev/t

Feb 28 11:14:36 compass systemd[1]: ambeserver@...: Main process exi

Feb 28 11:14:36 compass systemd[1]: ambeserver@...: Unit entered fai

Feb 28 11:14:36 compass systemd[1]: ambeserver@...: Triggering OnFai

Feb 28 11:14:36 compass systemd[1]: ambeserver@...: Failed with resu


I am looking for any advice or information about what I need to do to fix this problem.
 
Thank you.
 
Al
W4RAM
 
[Note: DVStick 30 is not a product of NW Digital Radio - Moderator]

Re: AMBEServer DVStick 30 Compass Raspberry Pi #ambeserver

Stefsan
 

Hi Mesa,

at first ive running AMBEServer also with DV30 Stick in perfect value. I am using a normal actual raspian image on a raspi zero W and a 2b+ also.

Normally its to know that the physical port ist /dev/ttyUSB0 ( its the first USB device) and second the portspeed its 460800 Baud somewhere in the AMBEserver start script the information must transfered by starting trhe AMBEServer.

The needed Port for Application communication is 2460 UDP.


What to do: check in terminal on pi or via ssh if you can attach following folder when DV30 is connected to usb port of raspberry with command   ls /dev/ttyUSB*      it must come back with /dev/ttyUSB0 if that is right usb connection is ok

Other Problem could be that your user ( most its pi) is not in the group dailout) check with   sudo nano /etc/group   and find the line with  it must look like this ( pi is important, if not add it) dailout:x:20:pi

best is use a actual raspian and compile ( make , make install) the "github resource AMBE Server Marrold" in only 2 steps and crate a desktop start script in .config/autostart .

If you need assistance contact me its very easy.

BR Stefan DL1ESZ



Am 28.02.19 um 18:04 schrieb Al Mesa:

Hello,
I am having the following issue:
CONDITIONS: Raspberry Pi 3B+ Compass Linux, DVStick 30.
ISSUE After install without problems the AMBEserver per instructions and after start the AMBEServer service, a few seconds after the AMBEServer services stop and failed.
Please see the terminal detail:
 

^Xroot@compass:~# systemctl start ambeserver@...

root@compass:~# systemctl status ambeserver@...

ambeserver@... - DV3000 Daemon

   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor pres

   Active: active (running) since Thu 2019-02-28 11:14:00 EST; 31s ago

  Process: 20143 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=

  Process: 20142 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, stat

 Main PID: 20148 (AMBEserver)

   CGroup: /system.slice/system-ambeserver.slice/ambeserver@...

           └─20148 /usr/sbin/AMBEserver -p 2460 -i /dev/ttyUSB0

 

Feb 28 11:14:00 compass systemd[1]: Starting DV3000 Daemon...

Feb 28 11:14:00 compass systemd[1]: Started DV3000 Daemon.

Feb 28 11:14:00 compass AMBEserver[20148]: AMBEserver: Starting...

Feb 28 11:14:00 compass AMBEserver[20148]: AMBEserver: Opened serial port /dev/t

 

/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

 

pi@compass:~ $ sudo systemctl status ambeserver@...

ambeserver@... - DV3000 Daemon

   Loaded: loaded (/lib/systemd/system/ambeserver@.service; enabled; vendor pres

   Active: failed (Result: exit-code) since Thu 2019-02-28 11:14:36 EST; 1min 27

  Process: 20148 ExecStart=/usr/sbin/AMBEserver -p ${UDP_PORT} -i /dev/ttyUSB0 $

  Process: 20143 ExecStartPre=/bin/chmod 0660 /dev/ttyUSB0 (code=exited, status=

  Process: 20142 ExecStartPre=/bin/chgrp dialout /dev/ttyUSB0 (code=exited, stat

 Main PID: 20148 (code=exited, status=1/FAILURE)

 

Feb 28 11:14:00 compass systemd[1]: Starting DV3000 Daemon...

Feb 28 11:14:00 compass systemd[1]: Started DV3000 Daemon.

Feb 28 11:14:00 compass AMBEserver[20148]: AMBEserver: Starting...

Feb 28 11:14:00 compass AMBEserver[20148]: AMBEserver: Opened serial port /dev/t

Feb 28 11:14:36 compass systemd[1]: ambeserver@...: Main process exi

Feb 28 11:14:36 compass systemd[1]: ambeserver@...: Unit entered fai

Feb 28 11:14:36 compass systemd[1]: ambeserver@...: Triggering OnFai

Feb 28 11:14:36 compass systemd[1]: ambeserver@...: Failed with resu


I am looking for any advice or information about what I need to do to fix this problem.
 
Thank you.
 
Al
W4RAM
 
[Note: DVStick 30 is not a product of NW Digital Radio - Moderator]

No light. Dongle fails test

va7vw@...
 

If there is no light and it fails the test, is it finished or can it be repaired?

Re: No light. Dongle fails test

 
Edited

It only lights when it tx or rx
Are you sure you have the correct com port selected in your software?
Link to a wealth of info:

https://1drv.ms/b/s!Atybf7djk0kciiYxu30hjrbQV7ba

Re: No light. Dongle fails test

 

Are you referring to a ThumbDV from NW Digital Radio?

Is it showing as a com port on your computer?


On Fri, Mar 1, 2019 at 10:34 PM <va7vw@...> wrote:
If there is no light and it fails the test, is it finished or can it be repaired?



--


John D. Hays
Edmonds, WA
K7VE

   

Re: Can 6 Digit DMR IDs work with BlueDV & AMBE Servers?? #dmrid, #ambe, # amberserver

Dev 9Y4DG
 

Thanks Jason... certainly worth a try
73 Dev

On Fri, Feb 22, 2019, 11:18 AM Jason Kingsbury <jkingsbury13@...> wrote:
Not sure if this will work, but have you tried to put a 0 (zero) in front of the six digit ID when configuring it on BlueDV? 


On Feb 8, 2019, at 1:56 PM, Dev Gosine <dgosine@...> wrote:

Good day,
                  Thank you for taking the time to read this message and also for your kind contribution to the thread.

Here are the facts.

1. I have 5 AMBE Servers.
2. I have 2 DMR IDs
3. BlueDV (Android) does not support adding an additional 2 digits to the end of the DMR ID as the DMR ID input field allows only 7 digits.
4. I have applied for additional DMR IDs, but was given five 6 digit repeater IDs.
5. This initially sounded like the perfect solution since I have 5 AMBE Servers and got 5 DMR IDs.
6. The problem is that the 6 digit DMR ID is not seen on Brandmeister's Hoseline when I transmit. This means I have absolutely no transmission being monitored on hoseline if I were to transmit.

Can anyone tell me what I'm doing wrong and possibly lead me in the correct direction.

I thank you again for all your contributions.....73 Dev, 9Y4DG
 

 

Re: Can 6 Digit DMR IDs work with BlueDV & AMBE Servers?? #dmrid, #ambe, # amberserver

Dev 9Y4DG
 

Hi Jason,
Unfortunately..that did not work.

Thanks again for your help....73 Dev


On Fri, 22 Feb 2019 at 11:18, Jason Kingsbury <jkingsbury13@...> wrote:
Not sure if this will work, but have you tried to put a 0 (zero) in front of the six digit ID when configuring it on BlueDV? 


On Feb 8, 2019, at 1:56 PM, Dev Gosine <dgosine@...> wrote:

Good day,
                  Thank you for taking the time to read this message and also for your kind contribution to the thread.

Here are the facts.

1. I have 5 AMBE Servers.
2. I have 2 DMR IDs
3. BlueDV (Android) does not support adding an additional 2 digits to the end of the DMR ID as the DMR ID input field allows only 7 digits.
4. I have applied for additional DMR IDs, but was given five 6 digit repeater IDs.
5. This initially sounded like the perfect solution since I have 5 AMBE Servers and got 5 DMR IDs.
6. The problem is that the 6 digit DMR ID is not seen on Brandmeister's Hoseline when I transmit. This means I have absolutely no transmission being monitored on hoseline if I were to transmit.

Can anyone tell me what I'm doing wrong and possibly lead me in the correct direction.

I thank you again for all your contributions.....73 Dev, 9Y4DG
 

 



--


“Your chances of success in any undertaking can
always be measured by your belief in yourself"
       ~Robert Collier~.

The pessimist complains about the wind.
The optimist expects it to change.
The leader adjusts the sails.

                 ~John Maxwell~

Teamwork is the ability to work together toward a common vision.
The ability to direct individual accomplishment toward organizational objectives.
It is the fuel that allows common people to attain uncommon results.
      ~ Anonymous~

We believe that:

"We make a living by what we get,
We make a life by what we give!"
          ~Winston Churchill~

Re: No light. Dongle fails test

va7vw@...
 

Thanks for the link. I have confirmed that it is on the correct com port.

Re: No light. Dongle fails test

va7vw@...
 

I am referring to a ThumbDV from NW Digital Radio.

It is showing as a USB com port on my PC.

AMBEServer Install for PiDV

Mike Besemer - WM4B
 

Greetings,

New guy here.

Trying to get AMBEServer installed on my Pi using Method 2 here: http://nwdigitalradio.com/dv3000-ambeserver/

I get as far as the ls command (below) before things go wrong.  When I run ls, the Makefile is not there.

I am not a Linux geek, but can generally follow directions.  What am I doing wrong?

73,

Mike

WM4B

apt-get install git

 

cd

git clone https://github.com/dl5di/OpenDV.git

Cloning into ‘OpenDV’…

remote: Counting objects: 2196, done.

remote: Total 2196 (delta 0), reused 0 (delta 0)

Receiving objects: 100% (2196/2196), 29.65 MiB | 2.05 MiB/s, done.

Resolving deltas: 100% (1444/1444), done.

Checking connectivity… done.

mv OpenDV/DummyRepeater/DV3000 DV3000

rm -rf OpenDV

cd DV3000

ls

AMBEserver.c  AMBEtest2.py  AMBEtest3.py  dv3000d-AMBEserver.pdf  dv3000d.c  init.d  Makefile  README-dv3000d.txt  README.txt

Re: AMBEServer Install for PiDV

 

Hi Mike

On Mon, Mar 11, 2019 at 4:38 PM Mike Besemer <mwbesemer@...> wrote:


I get as far as the ls command (below) before things go wrong.  When I run ls, the Makefile is not there.


ls

AMBEserver.c  AMBEtest2.py  AMBEtest3.py  dv3000d-AMBEserver.pdf  dv3000d.c  init.d  Makefile  README-dv3000d.txt  README.txt


Now type --
make

--


John D. Hays
Edmonds, WA
K7VE

   

Re: AMBEServer Install for PiDV

Mike Besemer - WM4B
 

John,

 

Typing ‘make’ yields the following:

 

pi@raspberrypi:~/DV3000 $ make

make: *** No targets specified and no makefile found.  Stop.

pi@raspberrypi:~/DV3000 $

 

Mike

WM4B

 

 

 

From: ambe@nw-digital-radio.groups.io [mailto:ambe@nw-digital-radio.groups.io] On Behalf Of John D Hays - K7VE
Sent: Monday, March 11, 2019 7:41 PM
To: ambe@nw-digital-radio.groups.io
Subject: Re: [ambe] AMBEServer Install for PiDV

 

Hi Mike

 

On Mon, Mar 11, 2019 at 4:38 PM Mike Besemer <mwbesemer@...> wrote:

 

I get as far as the ls command (below) before things go wrong.  When I run ls, the Makefile is not there.

 

ls

AMBEserver.c  AMBEtest2.py  AMBEtest3.py  dv3000d-AMBEserver.pdf  dv3000d.c  init.d  Makefile  README-dv3000d.txt  README.txt

 

Now type --

make

 

--

 


John D. Hays
Edmonds, WA

K7VE