Date   
Re: Can 6 Digit DMR IDs work with BlueDV & AMBE Servers?? #dmrid, #ambe, # amberserver

 

this would be a good question for PA7LIM David on his BLUEDV WEBSITE


From: ambe@nw-digital-radio.groups.io <ambe@nw-digital-radio.groups.io> on behalf of Dev Gosine <dgosine@...>
Sent: February 8, 2019 12:56 PM
To: ambe@nw-digital-radio.groups.io
Subject: [ambe] Can 6 Digit DMR IDs work with BlueDV & AMBE Servers?? #dmrid, #ambe, # amberserver
 

Good day,
                  Thank you for taking the time to read this message and also for your kind contribution to the thread.

Here are the facts.

1. I have 5 AMBE Servers.
2. I have 2 DMR IDs
3. BlueDV (Android) does not support adding an additional 2 digits to the end of the DMR ID as the DMR ID input field allows only 7 digits.
4. I have applied for additional DMR IDs, but was given five 6 digit repeater IDs.
5. This initially sounded like the perfect solution since I have 5 AMBE Servers and got 5 DMR IDs.
6. The problem is that the 6 digit DMR ID is not seen on Brandmeister's Hoseline when I transmit. This means I have absolutely no transmission being monitored on hoseline if I were to transmit.

Can anyone tell me what I'm doing wrong and possibly lead me in the correct direction.

I thank you again for all your contributions.....73 Dev, 9Y4DG
 

 

Can 6 Digit DMR IDs work with BlueDV & AMBE Servers?? #dmrid, #ambe, # amberserver

Dev Gosine
 

Good day,
                  Thank you for taking the time to read this message and also for your kind contribution to the thread.

Here are the facts.

1. I have 5 AMBE Servers.
2. I have 2 DMR IDs
3. BlueDV (Android) does not support adding an additional 2 digits to the end of the DMR ID as the DMR ID input field allows only 7 digits.
4. I have applied for additional DMR IDs, but was given five 6 digit repeater IDs.
5. This initially sounded like the perfect solution since I have 5 AMBE Servers and got 5 DMR IDs.
6. The problem is that the 6 digit DMR ID is not seen on Brandmeister's Hoseline when I transmit. This means I have absolutely no transmission being monitored on hoseline if I were to transmit.

Can anyone tell me what I'm doing wrong and possibly lead me in the correct direction.

I thank you again for all your contributions.....73 Dev, 9Y4DG
 

 

Re: How to create a multi-mode xreflector

TG9AOR
 

Nice Document. Thank you for sharing.

How to create a multi-mode xreflector

Dennis AD6DM
 

Might be off-topic but I found the NWDR ThumbDV fantastic for this lil project of mine. I wrote up a document to help people understand creating a cross-mode xreflector.
 
73 de Dennis AD6DM

Re: BlueDV and ThumbDV no DMR

 

RE: "What are the differences and benefits when comparing “IPSC2-MINNESOTA” and “USA-MINNESOTA2” and “IPSC2-USA-MN2”?"

Choose whatever DMR+ server you like.
The fellow with the issue used the UK Video from YouTube
From watching the UK video of BLUEDV setup everything was setup for the UK servers
I was just trying to steer the fellow ham in the direction of USA DMR+ servers.
His issue was not about which server to use be it “IPSC2-MINNESOTA” or“USA-MINNESOTA2”
His issue was he could not connect at all.
That is what I was focusing on.
After posting it to this group I contacted the fellow via his personal email account with my sample edited capture of the setup screen.
So by the time anyone else responded he was already configured and up on the air on DMR.
He sent me a shining email thanking me.
I am not interested in engaging any rhetoric, just wanted to get the fellow up and running simply and smoothly on USA servers not UK servers as
the YouTube video indicated.
I am sure  the fellow will experiment with what servers work best for him at his location.
Anyone who wishes can use my sample setup screen or whichever one gives them a warm and fuzzy feeling and gets them through the night.
Beyond this the matter is closed
Cheers & 73 de VE6DZ


From: ambe@nw-digital-radio.groups.io <ambe@nw-digital-radio.groups.io> on behalf of J G Shaw <WA6PX@...>
Sent: February 3, 2019 11:14 AM
To: ambe@nw-digital-radio.groups.io
Subject: Re: [ambe] BlueDV and ThumbDV no DMR
 

A BlueDV DMR+ question –

What are the differences and benefits when comparing “IPSC2-MINNESOTA” and “USA-MINNESOTA2” and “IPSC2-USA-MN2”?

Thanks

WA6PX

 

From: ambe@nw-digital-radio.groups.io [mailto:ambe@nw-digital-radio.groups.io] On Behalf Of Mavgk
Sent: Sunday, February 3, 2019 1:34 AM
To: ambe@nw-digital-radio.groups.io
Subject: Re: [ambe] BlueDV and ThumbDV no DMR

 

On Sat, Feb 2, 2019 at 11:23 PM, David - N5MXI wrote:

DMR Master 3102 passw1rd

Use   DMR Master 3108 passw0rd
DMR 3108 is more stable
passw1rd is for a UK server and passw0rd is for USA and Canada
Here is a sample that works.
Make your setup screen the same using your info in the areas in red and it WILL work.
EVERYTHING ELSE MUST BE IDENTICAL!


Re: BlueDV and ThumbDV no DMR

David Harris - WD0HDR
 

The password = passw0rd

 

 

From: ambe@nw-digital-radio.groups.io [mailto:ambe@nw-digital-radio.groups.io] On Behalf Of David - N5MXI
Sent: Saturday, February 2, 2019 23:48 PM
To: ambe@nw-digital-radio.groups.io
Subject: [ambe] BlueDV and ThumbDV no DMR

 

I am using a ThumbDV with BlueDV. I have configured BlueDV for BM type DMR and entered my DMR ID in DMR hotspot and simple. DMR Master 3102 passw1rd. I am unable to get the DMR  button at the lower left of the main BlueDV to show DMR connected. I have no trouble with D-Star connecting. Is the password for the Master correct? I can think of no other reason for not connecting.

Re: BlueDV and ThumbDV no DMR

J G Shaw
 

A BlueDV DMR+ question –

What are the differences and benefits when comparing “IPSC2-MINNESOTA” and “USA-MINNESOTA2” and “IPSC2-USA-MN2”?

Thanks

WA6PX

 

From: ambe@nw-digital-radio.groups.io [mailto:ambe@nw-digital-radio.groups.io] On Behalf Of Mavgk
Sent: Sunday, February 3, 2019 1:34 AM
To: ambe@nw-digital-radio.groups.io
Subject: Re: [ambe] BlueDV and ThumbDV no DMR

 

On Sat, Feb 2, 2019 at 11:23 PM, David - N5MXI wrote:

DMR Master 3102 passw1rd

Use   DMR Master 3108 passw0rd
DMR 3108 is more stable
passw1rd is for a UK server and passw0rd is for USA and Canada
Here is a sample that works.
Make your setup screen the same using your info in the areas in red and it WILL work.
EVERYTHING ELSE MUST BE IDENTICAL!


Re: BlueDV and ThumbDV no DMR

(null) (null)
 

Hi David 

The password I for DMR ls “passw0rd”. I hope this helps.

Frank k6fed 


On Feb 3, 2019, at 2:32 AM, J G Shaw <WA6PX@...> wrote:

I have attached a screen snip of my settings screen.  I am using a slightly different password.  Perhaps the same will work for you?  My password has a “zero” instead of a “one”.  If that doesn’t fix it, then I suggest changing your US DMR master e.g., I use 3103.

 

From: ambe@nw-digital-radio.groups.io [mailto:ambe@nw-digital-radio.groups.io] On Behalf Of David - N5MXI
Sent: Saturday, February 2, 2019 10:48 PM
To: ambe@nw-digital-radio.groups.io
Subject: [ambe] BlueDV and ThumbDV no DMR

 

I am using a ThumbDV with BlueDV. I have configured BlueDV for BM type DMR and entered my DMR ID in DMR hotspot and simple. DMR Master 3102 passw1rd. I am unable to get the DMR  button at the lower left of the main BlueDV to show DMR connected. I have no trouble with D-Star connecting. Is the password for the Master correct? I can think of no other reason for not connecting.

<190203 BkueDV setup screen capture.JPG>

Re: BlueDV and ThumbDV no DMR

 

On Sat, Feb 2, 2019 at 11:23 PM, David - N5MXI wrote:
DMR Master 3102 passw1rd
Use   DMR Master 3108 passw0rd
DMR 3108 is more stable
passw1rd is for a UK server and passw0rd is for USA and Canada
Here is a sample that works.
Make your setup screen the same using your info in the areas in red and it WILL work.
EVERYTHING ELSE MUST BE IDENTICAL!



Re: BlueDV and ThumbDV no DMR

J G Shaw
 

I have attached a screen snip of my settings screen.  I am using a slightly different password.  Perhaps the same will work for you?  My password has a “zero” instead of a “one”.  If that doesn’t fix it, then I suggest changing your US DMR master e.g., I use 3103.

 

From: ambe@nw-digital-radio.groups.io [mailto:ambe@nw-digital-radio.groups.io] On Behalf Of David - N5MXI
Sent: Saturday, February 2, 2019 10:48 PM
To: ambe@nw-digital-radio.groups.io
Subject: [ambe] BlueDV and ThumbDV no DMR

 

I am using a ThumbDV with BlueDV. I have configured BlueDV for BM type DMR and entered my DMR ID in DMR hotspot and simple. DMR Master 3102 passw1rd. I am unable to get the DMR  button at the lower left of the main BlueDV to show DMR connected. I have no trouble with D-Star connecting. Is the password for the Master correct? I can think of no other reason for not connecting.

BlueDV and ThumbDV no DMR

David - N5MXI
 

I am using a ThumbDV with BlueDV. I have configured BlueDV for BM type DMR and entered my DMR ID in DMR hotspot and simple. DMR Master 3102 passw1rd. I am unable to get the DMR  button at the lower left of the main BlueDV to show DMR connected. I have no trouble with D-Star connecting. Is the password for the Master correct? I can think of no other reason for not connecting.

Re: How to Change AMBEServer UDP Port Number?? #udpport #ambe #port

Dev Gosine
 

Thanks guys.....Your feedback and responses were awesome!!

Mission accomplished!!!....73 Dev, 9Y4DG


On Wed, 30 Jan 2019 at 15:48, John D Hays - K7VE <john@...> wrote:

A standard convention in Unix/Linux is to provide a simple usage message, by using an -h or --help flag to a command.

e.g.

ambeserver -h

will show you:
Usage: AMBEserver [-d] [-r] [-s speed] [-p port] [-i tty] [-v] [-x]\n

This shows you command line options to set the speed, port, and tty that ambeserver should use.



--


“Your chances of success in any undertaking can
always be measured by your belief in yourself"
       ~Robert Collier~.

The pessimist complains about the wind.
The optimist expects it to change.
The leader adjusts the sails.

                 ~John Maxwell~

Teamwork is the ability to work together toward a common vision.
The ability to direct individual accomplishment toward organizational objectives.
It is the fuel that allows common people to attain uncommon results.
      ~ Anonymous~

We believe that:

"We make a living by what we get,
We make a life by what we give!"
          ~Winston Churchill~

Re: How to Change AMBEServer UDP Port Number?? #udpport #ambe #port

 

A standard convention in Unix/Linux is to provide a simple usage message, by using an -h or --help flag to a command.

e.g.

ambeserver -h

will show you:
Usage: AMBEserver [-d] [-r] [-s speed] [-p port] [-i tty] [-v] [-x]\n

This shows you command line options to set the speed, port, and tty that ambeserver should use.

Re: How to Change AMBEServer UDP Port Number?? #udpport #ambe #port

Jorge
 

Sorry a typo

/usr/local/sbin/ambeserver -d -p 24999 -i /dev/ttyUSB0 -s 460800


On Wed, 30 Jan 2019 at 15:44, Jorge via Groups.Io <ct1jib=gmail.com@groups.io> wrote:
Hi all,

You can use switch "p" to change port number, exemp: usr/local/sbin/ambeserver -d -i -p 24999 /dev/ttyUSB0 -s 460800

Hope this help

On Wed, 30 Jan 2019 at 15:36, John D Hays - K7VE <john@...> wrote:
There are command line switches to set the port and device. 

On Wed, Jan 30, 2019, 05:05 Dev Gosine <dgosine@... wrote:
Thank you Frank for your very prompt response..

It seems as though you might be using Compass Linux. Unfortunately, I'm using Raspian Stretch., so there is no opendv folder and neither am I seeing any ambeserver-ttyUSB0.conf file to edit.

Thanks again buddy...73 Dev, 9Y4DG


On Wed, 30 Jan 2019 at 01:25, (null) (null) via Groups.Io <fdecuire=yahoo.com@groups.io> wrote:
Dev

I’m running multiple servers also and I did the following on the PI server:

pico /etc/opendv/ambeserver-ttyUSB0.conf
Changed the UDP port to 18307

Did UDP port forwarding on the router for 18307.

Frank k6fed 

On Jan 29, 2019, at 8:53 PM, Dev Gosine <dgosine@...> wrote:

Good day,
                   The AMBEServer defaults to port 2460. I would like to run multiple servers simultaneously. Of course, they can't all use port 2460 concurrently.

So the question is how does one change the UDP port either in the initialisation process of the Raspberry Pi and/or in the AMBE Server??

I suspect a file of two needs to be edited..... any ideas or suggestions??

I thank you for your contributions...73 Dev, 9Y4DG



--


“Your chances of success in any undertaking can
always be measured by your belief in yourself"
       ~Robert Collier~.

The pessimist complains about the wind.
The optimist expects it to change.
The leader adjusts the sails.

                 ~John Maxwell~

Teamwork is the ability to work together toward a common vision.
The ability to direct individual accomplishment toward organizational objectives.
It is the fuel that allows common people to attain uncommon results.
      ~ Anonymous~

We believe that:

"We make a living by what we get,
We make a life by what we give!"
          ~Winston Churchill~



--

73's

***********************************
CT1JIB / Jorge Santos
***********************************



--

73's

***********************************
CT1JIB / Jorge Santos
***********************************

Re: How to Change AMBEServer UDP Port Number?? #udpport #ambe #port

Jorge
 

Hi all,

You can use switch "p" to change port number, exemp: usr/local/sbin/ambeserver -d -i -p 24999 /dev/ttyUSB0 -s 460800

Hope this help

On Wed, 30 Jan 2019 at 15:36, John D Hays - K7VE <john@...> wrote:
There are command line switches to set the port and device. 

On Wed, Jan 30, 2019, 05:05 Dev Gosine <dgosine@... wrote:
Thank you Frank for your very prompt response..

It seems as though you might be using Compass Linux. Unfortunately, I'm using Raspian Stretch., so there is no opendv folder and neither am I seeing any ambeserver-ttyUSB0.conf file to edit.

Thanks again buddy...73 Dev, 9Y4DG


On Wed, 30 Jan 2019 at 01:25, (null) (null) via Groups.Io <fdecuire=yahoo.com@groups.io> wrote:
Dev

I’m running multiple servers also and I did the following on the PI server:

pico /etc/opendv/ambeserver-ttyUSB0.conf
Changed the UDP port to 18307

Did UDP port forwarding on the router for 18307.

Frank k6fed 

On Jan 29, 2019, at 8:53 PM, Dev Gosine <dgosine@...> wrote:

Good day,
                   The AMBEServer defaults to port 2460. I would like to run multiple servers simultaneously. Of course, they can't all use port 2460 concurrently.

So the question is how does one change the UDP port either in the initialisation process of the Raspberry Pi and/or in the AMBE Server??

I suspect a file of two needs to be edited..... any ideas or suggestions??

I thank you for your contributions...73 Dev, 9Y4DG



--


“Your chances of success in any undertaking can
always be measured by your belief in yourself"
       ~Robert Collier~.

The pessimist complains about the wind.
The optimist expects it to change.
The leader adjusts the sails.

                 ~John Maxwell~

Teamwork is the ability to work together toward a common vision.
The ability to direct individual accomplishment toward organizational objectives.
It is the fuel that allows common people to attain uncommon results.
      ~ Anonymous~

We believe that:

"We make a living by what we get,
We make a life by what we give!"
          ~Winston Churchill~



--

73's

***********************************
CT1JIB / Jorge Santos
***********************************

Re: How to Change AMBEServer UDP Port Number?? #udpport #ambe #port

Stefsan
 

Hi Dev,

as you remember before you compile (with make and make install) you had edit the ambeserver.c file with a editor (as root) to change in it the baudrate ( maybe you have), on one of the following line you can also change the port. Change them also and the baudrate and compile again ( with make and make install)

B.r.

Stefan DL1ESZ

Am 30.01.19 um 14:05 schrieb Dev Gosine:

Thank you Frank for your very prompt response..

It seems as though you might be using Compass Linux. Unfortunately, I'm using Raspian Stretch., so there is no opendv folder and neither am I seeing any ambeserver-ttyUSB0.conf file to edit.

Thanks again buddy...73 Dev, 9Y4DG


On Wed, 30 Jan 2019 at 01:25, (null) (null) via Groups.Io <fdecuire=yahoo.com@groups.io> wrote:
Dev

I’m running multiple servers also and I did the following on the PI server:

pico /etc/opendv/ambeserver-ttyUSB0.conf
Changed the UDP port to 18307

Did UDP port forwarding on the router for 18307.

Frank k6fed 

On Jan 29, 2019, at 8:53 PM, Dev Gosine <dgosine@...> wrote:

Good day,
                   The AMBEServer defaults to port 2460. I would like to run multiple servers simultaneously. Of course, they can't all use port 2460 concurrently.

So the question is how does one change the UDP port either in the initialisation process of the Raspberry Pi and/or in the AMBE Server??

I suspect a file of two needs to be edited..... any ideas or suggestions??

I thank you for your contributions...73 Dev, 9Y4DG



--


“Your chances of success in any undertaking can
always be measured by your belief in yourself"
       ~Robert Collier~.

The pessimist complains about the wind.
The optimist expects it to change.
The leader adjusts the sails.

                 ~John Maxwell~

Teamwork is the ability to work together toward a common vision.
The ability to direct individual accomplishment toward organizational objectives.
It is the fuel that allows common people to attain uncommon results.
      ~ Anonymous~

We believe that:

"We make a living by what we get,
We make a life by what we give!"
          ~Winston Churchill~

Re: How to Change AMBEServer UDP Port Number?? #udpport #ambe #port

 

There are command line switches to set the port and device. 


On Wed, Jan 30, 2019, 05:05 Dev Gosine <dgosine@... wrote:
Thank you Frank for your very prompt response..

It seems as though you might be using Compass Linux. Unfortunately, I'm using Raspian Stretch., so there is no opendv folder and neither am I seeing any ambeserver-ttyUSB0.conf file to edit.

Thanks again buddy...73 Dev, 9Y4DG


On Wed, 30 Jan 2019 at 01:25, (null) (null) via Groups.Io <fdecuire=yahoo.com@groups.io> wrote:
Dev

I’m running multiple servers also and I did the following on the PI server:

pico /etc/opendv/ambeserver-ttyUSB0.conf
Changed the UDP port to 18307

Did UDP port forwarding on the router for 18307.

Frank k6fed 

On Jan 29, 2019, at 8:53 PM, Dev Gosine <dgosine@...> wrote:

Good day,
                   The AMBEServer defaults to port 2460. I would like to run multiple servers simultaneously. Of course, they can't all use port 2460 concurrently.

So the question is how does one change the UDP port either in the initialisation process of the Raspberry Pi and/or in the AMBE Server??

I suspect a file of two needs to be edited..... any ideas or suggestions??

I thank you for your contributions...73 Dev, 9Y4DG



--


“Your chances of success in any undertaking can
always be measured by your belief in yourself"
       ~Robert Collier~.

The pessimist complains about the wind.
The optimist expects it to change.
The leader adjusts the sails.

                 ~John Maxwell~

Teamwork is the ability to work together toward a common vision.
The ability to direct individual accomplishment toward organizational objectives.
It is the fuel that allows common people to attain uncommon results.
      ~ Anonymous~

We believe that:

"We make a living by what we get,
We make a life by what we give!"
          ~Winston Churchill~

Re: How to Change AMBEServer UDP Port Number?? #udpport #ambe #port

Dev Gosine
 

Thank you Frank for your very prompt response..

It seems as though you might be using Compass Linux. Unfortunately, I'm using Raspian Stretch., so there is no opendv folder and neither am I seeing any ambeserver-ttyUSB0.conf file to edit.

Thanks again buddy...73 Dev, 9Y4DG


On Wed, 30 Jan 2019 at 01:25, (null) (null) via Groups.Io <fdecuire=yahoo.com@groups.io> wrote:
Dev

I’m running multiple servers also and I did the following on the PI server:

pico /etc/opendv/ambeserver-ttyUSB0.conf
Changed the UDP port to 18307

Did UDP port forwarding on the router for 18307.

Frank k6fed 

On Jan 29, 2019, at 8:53 PM, Dev Gosine <dgosine@...> wrote:

Good day,
                   The AMBEServer defaults to port 2460. I would like to run multiple servers simultaneously. Of course, they can't all use port 2460 concurrently.

So the question is how does one change the UDP port either in the initialisation process of the Raspberry Pi and/or in the AMBE Server??

I suspect a file of two needs to be edited..... any ideas or suggestions??

I thank you for your contributions...73 Dev, 9Y4DG



--


“Your chances of success in any undertaking can
always be measured by your belief in yourself"
       ~Robert Collier~.

The pessimist complains about the wind.
The optimist expects it to change.
The leader adjusts the sails.

                 ~John Maxwell~

Teamwork is the ability to work together toward a common vision.
The ability to direct individual accomplishment toward organizational objectives.
It is the fuel that allows common people to attain uncommon results.
      ~ Anonymous~

We believe that:

"We make a living by what we get,
We make a life by what we give!"
          ~Winston Churchill~

Re: How to Change AMBEServer UDP Port Number?? #udpport #ambe #port

(null) (null)
 

Dev

I’m running multiple servers also and I did the following on the PI server:

pico /etc/opendv/ambeserver-ttyUSB0.conf
Changed the UDP port to 18307

Did UDP port forwarding on the router for 18307.

Frank k6fed 

On Jan 29, 2019, at 8:53 PM, Dev Gosine <dgosine@...> wrote:

Good day,
                   The AMBEServer defaults to port 2460. I would like to run multiple servers simultaneously. Of course, they can't all use port 2460 concurrently.

So the question is how does one change the UDP port either in the initialisation process of the Raspberry Pi and/or in the AMBE Server??

I suspect a file of two needs to be edited..... any ideas or suggestions??

I thank you for your contributions...73 Dev, 9Y4DG

How to Change AMBEServer UDP Port Number?? #udpport #ambe #port

Dev Gosine
 

Good day,
                   The AMBEServer defaults to port 2460. I would like to run multiple servers simultaneously. Of course, they can't all use port 2460 concurrently.

So the question is how does one change the UDP port either in the initialisation process of the Raspberry Pi and/or in the AMBE Server??

I suspect a file of two needs to be edited..... any ideas or suggestions??

I thank you for your contributions...73 Dev, 9Y4DG