I cannot get realvnc to run on Compass.  I've tried manually installing it but without success.  Any suggestions?  I'm running Compass on a RPI3 with full updates and upgrades

John B

AD7QQ

Any help from yourselves who have do this already and suggestions of a good Raspberry Pi 2 or 3 image would be appreciated, initially the DMR to Analogue bridge sounds good for starters ?

John.

Hello John,

I guess it is possible; I have used my ThumbDV as a D_Star<> Analogue bridge.

See my post about Pi3;ThumbDV and Baofeng..

Regards,
Ian..


On 15-01-2017 20:45, John Anderson via Groups.Io wrote:

I have a PiDV which i purchased a number of years ago and was
wondering if i could put it to use to create a bridge between lets say
D-Star <-> DMR or from one of these modes to analogue FM ?

73 John Mi0AAZ.



Links:
------
[1] https://nw-digital-radio.groups.io/g/main/message/1469
[2] https://groups.io/mt/4185479?uid=162806
[3] https://nw-digital-radio.groups.io/g/main/post
[4] https://groups.io/mk?hashtag=cal-invite&subid=330593
[5] https://nw-digital-radio.groups.io/g/main/editsub?uid=162806
[6] https://nw-digital-radio.groups.io/g/main
[7] https://groups.io/static/tos
[8] https://nw-digital-radio.groups.io/g/main/leave/defanged

i can decode such digital voice data with dsdplus (software decoder)

i use hdsdr (sdrsoft) ... virtual audio cable (to route digital audio towards dsd) ... and the decoding software

hth

dg9bfc

sigi

ps ... with using thimb dv i can not help ... sorry

Am 12.01.2017 um 19:52 schrieb Dirk, DL2DW:

Hello,

Is it possible, to use the ThumbDV with SDR Software, like SDR#? Or can it be use, with the "Audio Virtual Cable" tool?

I want to decode DMR, D-STAR, etc. with my SDR receiver and a SDR software under Windows. My idea was, to take a ThumbDV to decode the stream from the sdr software.

Thank you in advance,

Dirk, DL2DW

Hello,

Is it possible, to use the ThumbDV with SDR Software, like SDR#? Or can it be use, with the "Audio Virtual Cable" tool?

I want to decode DMR, D-STAR, etc. with my SDR receiver and a SDR software under Windows. My idea was, to take a ThumbDV to decode the stream from the sdr software.

Thank you in advance,

Dirk, DL2DW

Hello,

Is it possible, to use the ThumbDV with SDR Software, like SDR#? Or can it be use, with the "Audio Virtual Cable" tool?

I want to decode DMR, D-STAR, etc. with my SDR receiver and a SDR software under Windows. My idea was, to take a ThumbDV to decode the stream from the sdr software.

Thank you in advance,

Dirk, DL2DW

OK I had the Deamon version of dstarrepeaterd running also so shutting off the GUI ones didn't  let me see that. How can I stop the Deamon one from starting at boot. 

My Problem is I receive on my repeater and it seems to go out over the Gate way but no Transmit out my Transmitter this is a converted old Repeater hotspot a couple of Motorola mobiles

You need to make sure dstarrepeater or dstarrepeaterd is completely stopped before running dstarrepeater 1

Then you will see the correct values -- which should be hw:0.0 (udrc)

Also you probably want to do this, so the built-in sound chip doesn't show up:

Optionally disable the internal sound chip by editing /boot/config.txt and commenting out this line (recommended unless you need it for something else):

#dtparam=audio=on

https://nw-digital-radio.groups.io/g/udrc/wiki/UDRC%E2%84%A2-For-Simplex-Hotspots-and-Converted-Analog-Repeaters

On Tue, Jan 3, 2017 at 6:21 PM, Ted McArthur <kb7pab@...> wrote:

I am wondering if this is correct setting in the Modem Tab I thought it used to be something else.

--

---

John D. Hays

K7VE

PO Box 1223, Edmonds, WA 98020-1223