|
Re: Good 2m rig?
Bill,
You missed one vendor, Bridgecom. They make a series of single band radios that have a 15 pin connector for interfacing. These are resonably priced ($240) units. I will be setting one up for
Bill,
You missed one vendor, Bridgecom. They make a series of single band radios that have a 15 pin connector for interfacing. These are resonably priced ($240) units. I will be setting one up for
|
By
Steve, N9VW
·
#2449
·
|
|
Re: Good 2m rig?
Here's a start of list where I was attempting to organize our options.
https://groups.io/g/nwaprs/wiki/Radios-for-Packet
Oh if only we had a modern Kantronics D4-10 with agile frequency
Here's a start of list where I was attempting to organize our options.
https://groups.io/g/nwaprs/wiki/Radios-for-Packet
Oh if only we had a modern Kantronics D4-10 with agile frequency
|
By
Bill Vodall
·
#2448
·
|
|
Re: Good 2m rig?
TM-V71 & FTM-100D.
I think there was a way to bring COS out of the TM-271, but that option disappeared on the -281.
I agree… for the extra $5 it would cost to add a dataport, I wish all the
TM-V71 & FTM-100D.
I think there was a way to bring COS out of the TM-271, but that option disappeared on the -281.
I agree… for the extra $5 it would cost to add a dataport, I wish all the
|
By
Mike Besemer - WM4B
·
#2447
·
|
|
Re: Good 2m rig?
I second Basil’s recommendation of the Kenwood TM-V71A. It’s a slight waste to have simultaneous dual band features with the data interface only to be able to work with one band or the other.
I second Basil’s recommendation of the Kenwood TM-V71A. It’s a slight waste to have simultaneous dual band features with the data interface only to be able to work with one band or the other.
|
By
Steve Stroh
·
#2446
·
|
|
Re: Good 2m rig?
I hadn't even gotten into philosophy yet... but I totally get what you're saying.
Right now I have no brand loyalty as I'm not yet an OM in this hobby. I've got Alinco, Kenwood, Yaesu, Elecraft,
I hadn't even gotten into philosophy yet... but I totally get what you're saying.
Right now I have no brand loyalty as I'm not yet an OM in this hobby. I've got Alinco, Kenwood, Yaesu, Elecraft,
|
By
Steve McGrane <temporarilyoffline@...>
·
#2445
·
|
|
Re: Good 2m rig?
Steve,
I know you think you asked a technical question but I believe it is more
philosophical. I am interested in other replies, however, I really like my
Kenwood TM-V71a. It has a mDin6 connector for
Steve,
I know you think you asked a technical question but I believe it is more
philosophical. I am interested in other replies, however, I really like my
Kenwood TM-V71a. It has a mDin6 connector for
|
By
Basil Gunn
·
#2444
·
|
|
Re: Good 2m rig?
I’ve had success with an ICOM IC-207H and a Kenwood TM-251A. The first thing I look for is the 6 pin mini-din or the capability for packet.
73
Jim
I’ve had success with an ICOM IC-207H and a Kenwood TM-251A. The first thing I look for is the 6 pin mini-din or the capability for packet.
73
Jim
|
By
Jim Erickson
·
#2443
·
|
|
Re: Good 2m rig?
I have successfully used an Alinco 135 MkIII and Yaesu FT-7900.
Purchased my cables from HamMadeParts.com
Ed Bloom, KD9FRQ
ewbloom@...
Sent from Webmail access
I have successfully used an Alinco 135 MkIII and Yaesu FT-7900.
Purchased my cables from HamMadeParts.com
Ed Bloom, KD9FRQ
ewbloom@...
Sent from Webmail access
|
By
Ed Bloom, KD9FRQ
·
#2442
·
|
|
Good 2m rig?
Is there a list of known compatible (or at least community aware working) radios?
My FT-891 is working fine on the HF side of things (should be back any day now) and I'm working on my TM-281, but I'm
Is there a list of known compatible (or at least community aware working) radios?
My FT-891 is working fine on the HF side of things (should be back any day now) and I'm working on my TM-281, but I'm
|
By
Steve McGrane <temporarilyoffline@...>
·
#2441
·
|
|
Re: Using a PiDrive with Draws Hat
#draws
#pidrive
From an Operating System point of view, "Compass" is Raspbian Linux.
--
John D. Hays
Kingston, WA
K7VE
From an Operating System point of view, "Compass" is Raspbian Linux.
--
John D. Hays
Kingston, WA
K7VE
|
By
John D Hays - K7VE
·
#2440
·
|
|
Re: Using a PiDrive with Draws Hat
#draws
#pidrive
I feel soooo bad you guys. I have not updated this for you. I did get my draws hat working fine on the new PI3B+. It is working just fine. I never tried again on the piDrive as it was working with
I feel soooo bad you guys. I have not updated this for you. I did get my draws hat working fine on the new PI3B+. It is working just fine. I never tried again on the piDrive as it was working with
|
By
okiejim
·
#2439
·
|
|
UDRC drivers on vanilla Raspbian (not compass)
Is there somewhere that the UDRC drivers can be found, to install them myself on Raspbian?
I am interested in building things up myself, instead of depending on pre-assembled compass linux.
Thanks!
Is there somewhere that the UDRC drivers can be found, to install them myself on Raspbian?
I am interested in building things up myself, instead of depending on pre-assembled compass linux.
Thanks!
|
By
Nathan Dykstra
·
#2438
·
|
|
Re: [New post] Hamvention is Upon US
Perhaps you could share the current status of DRAWS with those of us who cannot make it to Hamvention this year.
--
Steve Stroh (personal / general): stevestroh@...
Perhaps you could share the current status of DRAWS with those of us who cannot make it to Hamvention this year.
--
Steve Stroh (personal / general): stevestroh@...
|
By
Steve Stroh
·
#2437
·
|
|
[New post] Hamvention is Upon US
John Hays posted: "Hamvention begins Friday and we will be there again this year.Come by booth 1105 and visit with Bryan and John about the current status of the DRAWS
John Hays posted: "Hamvention begins Friday and we will be there again this year.Come by booth 1105 and visit with Bryan and John about the current status of the DRAWS
|
By
John D Hays - K7VE
·
#2436
·
|
|
No DRAWS Video... but some DRAWS content
I let the smoke out of my radio that I've been using for the DRAWS videos and I don't have a backup right now that works with DRAWS.
In the meantime I've got some parts in for testing when the radio
I let the smoke out of my radio that I've been using for the DRAWS videos and I don't have a backup right now that works with DRAWS.
In the meantime I've got some parts in for testing when the radio
|
By
Steve McGrane <temporarilyoffline@...>
·
#2435
·
|
|
Re: Why Do I get a "Windows" type GUI after a reboot??
You might want to expand on your description of what is happening because I for one don't have a clue what you are talking about?
No offense intended.
Gayland
KG7GCF
You might want to expand on your description of what is happening because I for one don't have a clue what you are talking about?
No offense intended.
Gayland
KG7GCF
|
By
Gayland Gump
·
#2434
·
|
|
Why Do I get a "Windows" type GUI after a reboot??
I really prefer the basic GUI and for no reason a boot will cause the darn "windows" type one to pop up!
I really prefer the basic GUI and for no reason a boot will cause the darn "windows" type one to pop up!
|
By
Allen Lee <alee@...>
·
#2433
·
|
|
Re: TAR.GZ FILES
Open a console window, go to directory you want to use and type:
tar xvzf some_file_name.tar.gz
If you have problems send me the console output.
Source for programs installed on the BETA images are
Open a console window, go to directory you want to use and type:
tar xvzf some_file_name.tar.gz
If you have problems send me the console output.
Source for programs installed on the BETA images are
|
By
Basil Gunn
·
#2432
·
|
|
.tar.gz Files
Im having problems get tar.gz files to install with DRAWS. Have several I want to install that the
Program Manager wont install or unpack. Also what is the best File or Directory to install other
Im having problems get tar.gz files to install with DRAWS. Have several I want to install that the
Program Manager wont install or unpack. Also what is the best File or Directory to install other
|
By
Allen Lee <alee@...>
·
#2431
·
|
|
Re: [New post] Shipping Status Update
#shipping
#draws
#case
Please use the form on the support page and include your order number.
Please use the form on the support page and include your order number.
|
By
John D Hays - K7VE
·
#2429
·
|