Date   
Re: Dayton

"John D. Hays" <john@...>
 

Booth EH0515

On Thu, May 14, 2015 at 6:23 AM, 'Tom Planer' tepcad@... [UniversalDigitalRadio] <UniversalDigitalRadio@...> wrote:
 

Will this group be represented at Dayton 2015?

KJ9P




--


John D. Hays
K7VE

PO Box 1223, Edmonds, WA 98020-1223 
  

Dayton

"Tom Planer" <tepcad@...>
 

Will this group be represented at Dayton 2015?

KJ9P

WinDV website

jd_hudson@...
 

I've been waiting to hear back from Fred (2 days) to get WinDV 1.5.8 and I've read where others emailed Fred from their contact info and not the web page form. I cannot load their page now or all day  http://dutch-star.eu. Is anyone else having this problem or can they send me Fred's more direct email. 

 

Thanks 

John 

KO4XJ 

Re: Amplifier Product

myyahoo@...
 

Excellent!

I definitely want one now. :-)

- Richard, VE7CVS

Re: Adding D-STAR to a Yaesu DR-1X Fusion Repeater

Matthew Pitts <daywalker_blade_2004@...>
 

Until such time as someone writes a module for Jonathan's software that allows System Fusion over D-STAR, yes.

Matthew Pitts
N8OHU


On May 10, 2015 9:26:33 AM EDT, "kc9gqr@... [UniversalDigitalRadio]" wrote:
 

So then  if an incoming signal comes in on Fusion  the devices  ignores it for the dstar routing  etc.   correct?  


--
Sent from my Moto X with K-9 Mail. Please excuse my brevity.

Re: Amplifier Product

bhhoyer@...
 

Not recommended. besides if you wanted a DVAP amp you probably are looking for more like a watt output (also not recommended)

Re: Amplifier Product

bhhoyer@...
 

I plan to add a LC Bandpass module as a plug-in option.

Re: Amplifier Product

bhhoyer@...
 

Good part, worth a look!

Re: Amplifier Product

bhhoyer@...
 

That's right, it says 20MHz in some places and 50MHz in others.

Just being conservative.

Bryan

Dayton Hamvention Program, Forum Schedule & Forum Details Attached

Mark Thompson <wb9qzb_groups@...>
 


Dayton Hamvention 
  • Program
  • Forum Schedule 
  • Forum Details 


Attached






Re: Adding D-STAR to a Yaesu DR-1X Fusion Repeater

kc9gqr@...
 

So then  if an incoming signal comes in on Fusion  the devices  ignores it for the dstar routing  etc.   correct?  

Re: Adding D-STAR to a Yaesu DR-1X Fusion Repeater

Bill Bennett <bennevl@...>
 

What about the possibility of adding this to a Fusion radio instead of a repeater? Especially in an environment where no internet is available. I have recently seen a video on Youtube of this done but with DVRPTR.
Bill K4IBC

Re: Adding D-STAR to a Yaesu DR-1X Fusion Repeater

"John D. Hays" <john@...>
 

The D-STAR mode runs on G4KLX dstarrepeater software, which in turn can talk to ircDDBGateway and out to the rest of the ircDDB connected net, including reflectors, STARnet Digital Groups, and callsign routing.

On Sat, May 9, 2015 at 8:19 PM, kc9gqr@... [UniversalDigitalRadio] <UniversalDigitalRadio@...> wrote:
 

Would you be able to LINK to other Dstar repeaters with this solution



John D. Hays
K7VE

PO Box 1223, Edmonds, WA 98020-1223 
  

Re: Adding D-STAR to a Yaesu DR-1X Fusion Repeater

kc9gqr@...
 

Would you be able to LINK to other Dstar repeaters with this solution

Re: Adding D-STAR to a Yaesu DR-1X Fusion Repeater

Matthew Pitts <daywalker_blade_2004@...>
 

John,

This seems interesting; I don't know if I will make it to Dayton this year, but you've got me thinking about the possibilities depending on how this goes together.

Matthew Pitts
N8OHU


From: "'John D. Hays' john@... [UniversalDigitalRadio]"
To: "dstar_digital@..." ; ircddbgateway ; "pcrepeatercontroller@..." ; "UniversalDigitalRadio@..."
Sent: Saturday, May 9, 2015 11:45 AM
Subject: [UniversalDigitalRadio] Adding D-STAR to a Yaesu DR-1X Fusion Repeater

 
Read about it at http://wp.me/p2mAAP-z7

--


John D. Hays
K7VE

PO Box 1223, Edmonds, WA 98020-1223 
  



Adding D-STAR to a Yaesu DR-1X Fusion Repeater

"John D. Hays" <john@...>
 

Read about it at http://wp.me/p2mAAP-z7

--


John D. Hays
K7VE

PO Box 1223, Edmonds, WA 98020-1223 
  

Re: Amplifier Product

myyahoo@...
 

I would buy one!

Something that wideband could be subject to swamping around here, I might want a filter in front of it - but it would be worth experimenting with, so to option of a power tee would be welcome. Looks useful as a driver amp, too, for some SDR experiments.

- Richard, VE7CVS

Re: Amplifier Product

Robert Copelan <rcopelan@...>
 

Brian, 
I'm didn't make it through EE (changed majors to computer science) so maybe this is a stupid question.   Would your device be useful when put on the end of a DVMega or DVAP as an amp?    I have heard that this is not a good idea since the signal out isn't clean enough to be amplified but not sure about that either.   

Thanks for the feedback.
Robert


On Thu, May 7, 2015 at 5:22 PM, bhhoyer@... [UniversalDigitalRadio] <UniversalDigitalRadio@...> wrote:
 

Hi All,


I'm busy finalizing the PA stage and in the process I built a driver amp so my 0 dBm tracking generator can drive PA modules at 50 mW (17 dBm).


I have the layout sitting in a folder and I was wondering if I'm the only guy that needs this:


Amplifier:


Frequency: 50 MHz to 6 GHz

Gain: 20 dB

Power: 1 dB compression at ~ 20 dBm

Supply: 5 VDC @ ~75 mA

NF: 3 dB at 900 MHz


It's based on the ADL5542 from Analog Devices. They want $100 for an unpackaged eval board.


We could put it in a case with SMA in/out and sell it for $40 including a Bias Tee so you could power it over the coax.


Also thinking about an LNA in the same form factor ...


Let us know if this might be interesting and what you would do with it.


Inquiring minds want to know ...


K7UDR


AW: Amplifier Product

"siegfried jackstien" <siegfried.jackstien@...>
 

I would use a pga 103+ and use it as an lna at the antenna

Lower noise figure and higher ip3

Dg9bfc

Sigi

-----Ursprüngliche Nachricht-----
Von: UniversalDigitalRadio@...
[mailto:UniversalDigitalRadio@...]
Gesendet: Donnerstag, 7. Mai 2015 21:22
An: UniversalDigitalRadio@...
Betreff: [UniversalDigitalRadio] Amplifier Product



Hi All,




I'm busy finalizing the PA stage and in the process I built a driver amp
so my 0 dBm tracking generator can drive PA modules at 50 mW (17 dBm).




I have the layout sitting in a folder and I was wondering if I'm the only
guy that needs this:




Amplifier:




Frequency: 50 MHz to 6 GHz

Gain: 20 dB

Power: 1 dB compression at ~ 20 dBm

Supply: 5 VDC @ ~75 mA

NF: 3 dB at 900 MHz




It's based on the ADL5542 from Analog Devices. They want $100 for an
unpackaged eval board.




We could put it in a case with SMA in/out and sell it for $40 including a
Bias Tee so you could power it over the coax.




Also thinking about an LNA in the same form factor ...




Let us know if this might be interesting and what you would do with it.




Inquiring minds want to know ...




K7UDR

Re: Amplifier Product

Dave <dave@...>
 

  The spec sheet says it can be used down to 20 MHz.   

Dave - WB6DHW


On 5/7/2015 2:22 PM, bhhoyer@... [UniversalDigitalRadio] wrote:
 

Hi All,


I'm busy finalizing the PA stage and in the process I built a driver amp so my 0 dBm tracking generator can drive PA modules at 50 mW (17 dBm).


I have the layout sitting in a folder and I was wondering if I'm the only guy that needs this:


Amplifier:


Frequency: 50 MHz to 6 GHz

Gain: 20 dB

Power: 1 dB compression at ~ 20 dBm

Supply: 5 VDC @ ~75 mA

NF: 3 dB at 900 MHz


It's based on the ADL5542 from Analog Devices. They want $100 for an unpackaged eval board.


We could put it in a case with SMA in/out and sell it for $40 including a Bias Tee so you could power it over the coax.


Also thinking about an LNA in the same form factor ...


Let us know if this might be interesting and what you would do with it.


Inquiring minds want to know ...


K7UDR