Date   
Re: SECOND Request Re: [nw-digital-radio] [New post] Shipping Status Update #draws #case #shipping

K4SPB
 

Ok but early adopters have old hats and old pis so where are those cases

Pi ft817 help please

andy.howe31@...
 

Help please,
Just got a pi4 I need the lead from the pi to yaesu817 but unsure which one I need,can someone help ?do  I need a sound card for the pi relay am new to all this so baby steps and learning curve ahead and hoping to keep it cheap as chips,I did buy a ud04ya lead for pc and mac but failed at getting that working 
Am hoping to tx and rx using FLDIGI and other modes,please can anyone help andy uk 

Re: Pi ft817 help please

Ed Bloom, KD9FRQ
 

https://hammadeparts.com/ is a great place to get your cables. Yes, that means shipping from the US to the UK.

You fellow UK compatriots make know of a source in county.

On 7/21/2019 9:27 AM, andy.howe31 via Groups.Io wrote:
Help please,
Just got a pi4 I need the lead from the pi to yaesu817 but unsure which one I need,can someone help ?do?? I need a sound card for the pi relay am new to all this so baby steps and learning curve ahead and hoping to keep it cheap as chips,I did buy a ud04ya lead for pc and mac but failed at getting that working??
Am hoping to tx and rx using FLDIGI and other modes,please can anyone help andy uk??

Re: Pi ft817 help please

 

You want two leads. The mini-DIN 6 cable that comes with the DRAWS™ HAT (or any similar cable) and a CT-62 equivalent cable for CAT control. (many offered on eBay and Amazon). 

Go into the UDRC and DRAWS ™ subgroup to this forum for help and advice.  

On Sun, Jul 21, 2019, 09:04 andy.howe31 via Groups.Io <andy.howe31=yahoo.co.uk@groups.io> wrote:
Help please,
Just got a pi4 I need the lead from the pi to yaesu817 but unsure which one I need,can someone help ?do  I need a sound card for the pi relay am new to all this so baby steps and learning curve ahead and hoping to keep it cheap as chips,I did buy a ud04ya lead for pc and mac but failed at getting that working 
Am hoping to tx and rx using FLDIGI and other modes,please can anyone help andy uk 

Re: Pi ft817 help please

andy.howe31@...
 

Thanks will do what does draw stand for? 

Re: Pi ft817 help please

Jack Spitznagel
 

Hi Andrew,

 

Please take a look at: http://nwdigitalradio.com/draws/

Good explanation and starting point.

The DRAWS + RPi combo works well with my FT-817.

 

KD4IZ

Jack Spitznagel

FM19oo

 

 

 

From: main@nw-digital-radio.groups.io <main@nw-digital-radio.groups.io> On Behalf Of Andrew Howe via Groups.Io
Sent: Sunday, July 21, 2019 14:00
To: main@nw-digital-radio.groups.io
Subject: Re: [nw-digital-radio] Pi ft817 help please

 

Thanks will do what does draw stand for? 

Re: Pi ft817 help please

WB7DFV
 

Hi Andrew,

Apparently, the word DRAWS is an acronym for Digital Radio Amateur WorkStation.  I know you and I would expect the first sentence after "What Is DRAWS?"  to contain that information but it does not -- go figure.  The picture caption has this information in a light grayish color.

73,

Dave WB7DFV

On 7/21/2019 11:10 AM, Jack Spitznagel wrote:

Hi Andrew,

 

Please take a look at: http://nwdigitalradio.com/draws/

Good explanation and starting point.

The DRAWS + RPi combo works well with my FT-817.

 

KD4IZ

Jack Spitznagel

FM19oo

 

 

 

From: main@nw-digital-radio.groups.io <main@nw-digital-radio.groups.io> On Behalf Of Andrew Howe via Groups.Io
Sent: Sunday, July 21, 2019 14:00
To: main@nw-digital-radio.groups.io
Subject: Re: [nw-digital-radio] Pi ft817 help please

 

Thanks will do what does draw stand for? 

Re: Pi ft817 help please

 

BTW the CT-62 can be USB or Serial. 


On Sun, Jul 21, 2019, 12:42 WB7DFV <wb7dfv@...> wrote:

Hi Andrew,

Apparently, the word DRAWS is an acronym for Digital Radio Amateur WorkStation.  I know you and I would expect the first sentence after "What Is DRAWS?"  to contain that information but it does not -- go figure.  The picture caption has this information in a light grayish color.

73,

Dave WB7DFV

On 7/21/2019 11:10 AM, Jack Spitznagel wrote:

Hi Andrew,

 

Please take a look at: http://nwdigitalradio.com/draws/

Good explanation and starting point.

The DRAWS + RPi combo works well with my FT-817.

 

KD4IZ

Jack Spitznagel

FM19oo

 

 

 

From: main@nw-digital-radio.groups.io <main@nw-digital-radio.groups.io> On Behalf Of Andrew Howe via Groups.Io
Sent: Sunday, July 21, 2019 14:00
To: main@nw-digital-radio.groups.io
Subject: Re: [nw-digital-radio] Pi ft817 help please

 

Thanks will do what does draw stand for? 

Re: Motorola Quantar & digital modes

Roger
 

Mike,
what all was involved (hardware and configuration) in the “Frankenstein” setup using the Quantar for the Tx and the other radio for the Rx. I have 2 VHF Quantars and would love to be able to use one on DMR. 

Re: Motorola Quantar & digital modes

Roger
 

Mike,
you can disregard my last post. I reread your post and realize it was a quote from another post elsewhere. The “Frankenstein” wasn’t yours for me to ask about.
Unless someone else knows what that config was for the Quantar and other radio, sorry for the confusion. 

Roger
VE7WWD

3D drawings?

Dave C
 

I'm considering using the DRAWS HAT in a device I'm designing.  I want to include it in my 3D design, but I can't find dimensions.  Do 3D drawings exist?

Re: Draws hat two weeks old defective

Michael Narges
 

As you suggested, I sent my dead Hat to you a couple weeks ago.  Please advise regarding turn around time.  Also, please also replace the power pigtail because the red lead broke off. Please let me know what I owe.

Thanks,

Mike. WF8O 

Re: Draws hat two weeks old defective

 

Mike,

Please use the form at http://nwdigitalradio.com/support/ for order/support communications.

On Tue, Jul 30, 2019 at 9:56 AM Michael Narges <mnarges23@...> wrote:
As you suggested, I sent my dead Hat to you a couple weeks ago.  Please advise regarding turn around time.  Also, please also replace the power pigtail because the red lead broke off. Please let me know what I owe.

Thanks,

Mike. WF8O 



John D. Hays
Director

  

Re: 3D drawings?

 

Hi Dave,

No, we don’t have 3D Drawings of the board.

Thanks,
Bryan K7UDR

On Jul 27, 2019, at 5:53 PM, Dave C <kd2jip@...> wrote:

I'm considering using the DRAWS HAT in a device I'm designing.  I want to include it in my 3D design, but I can't find dimensions.  Do 3D drawings exist?

Re: 3D drawings?

Dale Atkin
 

Dave,
What format would want the 3D models in? I use SolidWorks and could output it as IGES, STEP, or native SWX. Of course, I would need permission of Northwest Digital to create the models. It wouldn't take me that long to backward engineer my HAT.

Thanks,

Dale KE8GTV

Re: 3D drawings?

K2RI - Nick
 

I use the Free Hobbyist licence of Fusion 360

I too would welcome the models- I think any of the formats listed would work.

Thank you very much for your efforts.

73,

Nick  K2RI

On Wed, Jul 31, 2019 at 10:25 AM Dale Atkin <dacelt43@...> wrote:
Dave,
What format would want the 3D models in? I use SolidWorks and could output it as IGES, STEP, or native SWX. Of course, I would need permission of Northwest Digital to create the models. It wouldn't take me that long to backward engineer my HAT.

Thanks,

Dale KE8GTV



--

Re: 3D drawings?

 

Dale,

We’d be happy to give permission.

Contact me at sales@nwdigitalradio and we’ll work out the details.

Thanks,
Bryan K7UDR

Re: 3D drawings?

Dale Atkin
 

Would something like this have sufficient level of detail for a 3D model? This is a screenshot of a Pi3B:
image.png

Thanks,

Dale KE8GTV

On Wed, Jul 31, 2019 at 11:35 AM K2RI - Nick <nicholas.mohr@...> wrote:
I use the Free Hobbyist licence of Fusion 360

I too would welcome the models- I think any of the formats listed would work.

Thank you very much for your efforts.

73,

Nick  K2RI

On Wed, Jul 31, 2019 at 10:25 AM Dale Atkin <dacelt43@...> wrote:
Dave,
What format would want the 3D models in? I use SolidWorks and could output it as IGES, STEP, or native SWX. Of course, I would need permission of Northwest Digital to create the models. It wouldn't take me that long to backward engineer my HAT.

Thanks,

Dale KE8GTV



--

Re: 3D drawings?

kwangsoo han
 

Hi, Dear;

I'm Han in Seoul, Korea.

I bought the Thumdv as DV3000 about one year ago.

Unfortunately, I failed the test with your recommanded test software.

I'd like to test mine is ok or not.

What can I do for that.

Pls inform to me in detail.

Rds, kshan
 

--------------- Original message -------------
From : "Bryan Hoyer"<bhhoyer@...>
To : <main@nw-digital-radio.groups.io>
CC :
Date : Thu, 1 Aug 2019 1:10:54 +0900 (KST), Wed, 31 Jul 2019 09:10:48 -0700
Subject : Re: [nw-digital-radio] 3D drawings?

Dale,

We’d be happy to give permission.

Contact me at sales@nwdigitalradio and we’ll work out the details.

Thanks,
Bryan K7UDR






Re: 3D drawings?

 

Hello Han,


Are you on Windows, MacOS, or Linux?  

Has the ThumbDV been operational and then recently quit?

Does the LED flash when you test it?

On Wed, Jul 31, 2019 at 9:21 AM kwangsoo han <kshan315@...> wrote:
Hi, Dear;

I'm Han in Seoul, Korea.

I bought the Thumdv as DV3000 about one year ago.

Unfortunately, I failed the test with your recommanded test software.

I'd like to test mine is ok or not.

What can I do for that.

Pls inform to me in detail.

Rds, kshan
 
--------------- Original message -------------
From : "Bryan Hoyer"<bhhoyer@...>
To : <main@nw-digital-radio.groups.io>
CC :
Date : Thu, 1 Aug 2019 1:10:54 +0900 (KST), Wed, 31 Jul 2019 09:10:48 -0700
Subject : Re: [nw-digital-radio] 3D drawings?

Dale,

We’d be happy to give permission.

Contact me at sales@nwdigitalradio and we’ll work out the details.

Thanks,
Bryan K7UDR








--


John D. Hays
Director