|
Good 2m rig?
Try setting the PC baud rate on the radio to 57600. Also try connecting a serial program like screen and typing in the radio ID string. It should respond with 'OK'. screen /dev/ttyUSB0 57600 TMV71 or
Try setting the PC baud rate on the radio to 57600. Also try connecting a serial program like screen and typing in the radio ID string. It should respond with 'OK'. screen /dev/ttyUSB0 57600 TMV71 or
|
By
Basil Gunn
· #2490
·
|
|
Good 2m rig?
Check out a recent script (wlgw-check.sh) I wrote for rig control of the tm-v71. https://github.com/n7nix/auto-rmsgw-find This script iterates through a list of RMS gateways using a TM-V71a and Hamlib
Check out a recent script (wlgw-check.sh) I wrote for rig control of the tm-v71. https://github.com/n7nix/auto-rmsgw-find This script iterates through a list of RMS gateways using a TM-V71a and Hamlib
|
By
Basil Gunn
· #2489
·
|
|
Good 2m rig?
I now have a TM-V71a connected to my UDRC and am trying to get rigctl to work with it. I have an equivalent of a PG-5H connected to a serial/USB converter enumerated as /dev/ttyUSB0. My first test of
I now have a TM-V71a connected to my UDRC and am trying to get rigctl to work with it. I have an equivalent of a PG-5H connected to a serial/USB converter enumerated as /dev/ttyUSB0. My first test of
|
By
Keith Williamson
· #2488
·
|
|
Using a PiDrive with Draws Hat
#draws
#pidrive
Yes
By
Sam Wash
· #2487
·
|
|
Using a PiDrive with Draws Hat
#draws
#pidrive
https://thepi.io/how-to-boot-your-raspberry-pi-from-a-usb-mass-storage-device/
https://thepi.io/how-to-boot-your-raspberry-pi-from-a-usb-mass-storage-device/
|
By
John D Hays - K7VE
· #2486
·
|
|
Using a PiDrive with Draws Hat
#draws
#pidrive
I’ve been booting from the external Toshiba 500gig USB drive for years but the Pi still needs /boot on the SD card to read the configuration then continues booting from the external drive. In your cas
I’ve been booting from the external Toshiba 500gig USB drive for years but the Pi still needs /boot on the SD card to read the configuration then continues booting from the external drive. In your cas
|
By
k6acj
· #2485
·
|
|
Using a PiDrive with Draws Hat
#draws
#pidrive
Thank you Christopher, I kinda knew that but my attempt was to use the 12 volt input to power everything. I am using the draws in my RV/ToyHauler and 12volt amps do fluctuate during times of no hookup
Thank you Christopher, I kinda knew that but my attempt was to use the 12 volt input to power everything. I am using the draws in my RV/ToyHauler and 12volt amps do fluctuate during times of no hookup
|
By
okiejim
· #2484
·
|
|
2m rig Update
Thanks for getting back to me. DRAWS Side: Pin 3/Orange writing 1 to pin 12 will raise voltage to 4.22v PTT light goes on Pin 3/Orange writing 0 to pin 12 will lower voltage to 3.6mv PTT light goes of
Thanks for getting back to me. DRAWS Side: Pin 3/Orange writing 1 to pin 12 will raise voltage to 4.22v PTT light goes on Pin 3/Orange writing 0 to pin 12 will lower voltage to 3.6mv PTT light goes of
|
By
...
· #2483
·
|
|
2m rig Update
Verify the DRAWS hat -------------------- Disconnect the cable from your radio but plug into DRAWS hat on the open connector put your volt meter on what you think is the PTT pin Manually turn the gpio
Verify the DRAWS hat -------------------- Disconnect the cable from your radio but plug into DRAWS hat on the open connector put your volt meter on what you think is the PTT pin Manually turn the gpio
|
By
Basil Gunn
· #2482
·
|
|
2m rig Update
I got some time today (its raining!) to play with this. Initially the measure_deviation.sh script would run and not trip the PTT circuit. So I re-wired the cable and after looking more closely, I don'
I got some time today (its raining!) to play with this. Initially the measure_deviation.sh script would run and not trip the PTT circuit. So I re-wired the cable and after looking more closely, I don'
|
By
...
· #2481
·
|
|
2m rig Update
To debug PTT issues: Use the 'How to use measure_deviate.sh' notes here: https://github.com/nwdigitalradio/n7nix/tree/master/deviation Use left & right connector locations and either tune a second rad
To debug PTT issues: Use the 'How to use measure_deviate.sh' notes here: https://github.com/nwdigitalradio/n7nix/tree/master/deviation Use left & right connector locations and either tune a second rad
|
By
Basil Gunn
· #2480
·
|
|
2m rig Update
Follow-up to the cable issue. I've double checked the setup. If I put the hand mic back in line and Press PTT, my receiving radio breaks squelch, so it would seem that the PTT circuit is not activatin
Follow-up to the cable issue. I've double checked the setup. If I put the hand mic back in line and Press PTT, my receiving radio breaks squelch, so it would seem that the PTT circuit is not activatin
|
By
...
· #2479
·
|
|
Good 2m rig?
Bill, 6 pin mini din 1200 and 9600 although I've only used on 1200. Doug VE1ZG
Bill, 6 pin mini din 1200 and 9600 although I've only used on 1200. Doug VE1ZG
|
By
Doug Henry
· #2478
·
|
|
Good 2m rig?
6 pin mini-din or other? 1200 baud and/or 9600 baud?
6 pin mini-din or other? 1200 baud and/or 9600 baud?
|
By
Bill Vodall
· #2477
·
|
|
Good 2m rig?
The Icom IC-7000 has a data port that works well for packet. Doug VE1ZG
The Icom IC-7000 has a data port that works well for packet. Doug VE1ZG
|
By
Doug Henry
· #2476
·
|
|
Good 2m rig?
You are comparing apples and oranges. The "Data Port" on ham radios is a misnomer. It is a port for audio connections, just like the microphone jack. It typically has PTT, TX and RX audio (often from
You are comparing apples and oranges. The "Data Port" on ham radios is a misnomer. It is a port for audio connections, just like the microphone jack. It typically has PTT, TX and RX audio (often from
|
By
...
· #2475
·
|
|
Using a PiDrive with Draws Hat
#draws
#pidrive
The problem you are experiencing is being caused by the lack of power to run the hard drive. Buy yourself a Y USB splitter to allow the drive to be powered from a separate supply. Make sure the voltag
The problem you are experiencing is being caused by the lack of power to run the hard drive. Buy yourself a Y USB splitter to allow the drive to be powered from a separate supply. Make sure the voltag
|
By
Christopher Warren
· #2474
·
|
|
Using a PiDrive with Draws Hat
#draws
#pidrive
I just plugged the harddrive into a USB port on the Pi3. I now get the lightning bolt when the drvie is accessed. When idle the lightning bolt is not on. So it is working but un-sure at this point abo
I just plugged the harddrive into a USB port on the Pi3. I now get the lightning bolt when the drvie is accessed. When idle the lightning bolt is not on. So it is working but un-sure at this point abo
|
By
okiejim
· #2473
·
|
|
Using a PiDrive with Draws Hat
#draws
#pidrive
Success!!! I unplugged all my accessories and also unhooked the drive power from the Pi. So I have two power inputs at this time. The Pi is powered by the 12 volts from the Draws Hat and the Drive is
Success!!! I unplugged all my accessories and also unhooked the drive power from the Pi. So I have two power inputs at this time. The Pi is powered by the 12 volts from the Draws Hat and the Drive is
|
By
okiejim
· #2472
·
|
|
Draws hat
#draws
It would be nice to have a little more information on shipping dates, and order status
It would be nice to have a little more information on shipping dates, and order status
|
By
Rob Lapham
· #2471
·
|