Is there any date for shipping of the cases? My previous email to the group has went unanswered for two weeks. -- Dave Slotter, W3DJS

Since the Yeasu DRx1,(thats what our club has on aire); is no longer in production. Will the DRAWS still be able to be set up for DRX2? Al WB7SWW

Ever since I installed my Draws hat the RPI 3b+ slowed down and it takes ages to boot and to shutdown. During booting the CPU % reaches 100% before recovering. Yesterday I was using fldigi and during

I have aded a new case design for the DRAWS Hat (Jun-2019 edition with the GPS SMA port at the back. https://www.thingiverse.com/thing:3743033 I may look at adding power poles to it, probably as a rep

Has anyone operated WinMor or ARDOP sucessfully with the DRAWS Pi HAT and a Pi3+? More specifically with a FT857D? Thank you! Jim WA9PYH

Is it possible to run piardopc by John Wiseman with the DRAWS hat? If so, what startup parameters would I use? 73, Jason KM4ACK Find me on YouTube

The new Raspberry PI 4 has just been released. The PI4 is a serious upgrade over the PI3B. I'm guessing and hoping that DRAWS HAT is compatible, but I would like confirmation. So, will the DRAWS HAT w

k7udr posted: "We do not have a definitive ship date for Aluminum Cases yet, as a few details are being worked out. Acrylic cases are available from C4Labs here: DRAWSCase DRAWS Boards are in assembly

Its been a while, but now that my radio is back from factory service, I got the kick in the pants I needed to make another video. This video is all about how to make a bootable backup of your SD card

Here is a cheatsheet to get you started. https://files.fosswire.com/2007/08/fwunixref.pdf -- John D. Hays Director

I'm not getting what I think would be the right audio in/out from the DRAWS. I've tried a second cable and the second port. I get some input, but not 100% and I get no output in FT8 or JS8Call. When I

Hi Folks I’ve been busy working on some new bits of software. Both of them target the UDRC on a Raspberry Pi as a platform, and offer some interesting new avenues for experimentation. Firstly I ported

I really prefer the basic GUI and for no reason a boot will cause the darn "windows" type one to pop up!

Trying to find a cable to match the 8pin mini din on 7610 to 6pin din on DRAWS. Just not able to wire one myself, shake too much when soldering.

I'm chasing this PTT issue on my 2m unit and I'm not sure where to go from here. I'm out of parts or ideas or both. The DRAWS hat will signal PTT and the radio will open transmit and send as it is sup

I didn't see this when searching the archives... I have a bad habit of turning off my PS without shutting down the Pi... the thing is so quiet that I forget that its running. Would the DRAWS supplying

#udrc-dkms #dkms #rpi udrc-dkms fails to install after updating system/kernel as seen below. 73 de AI6KG pi@draws:~ $ sudo apt update Hit:1 http://archive.compasslinux.org cedar InRelease Hit:2 http:/

Include evaluation of the Kenwood Dual / Tri Band SkyCommand radios. They allow you to use a Kenwood Walkie Talkie with a built in TNC, to digitally link to a remote Kenwood Dual Band radio with a TNC

Is there a list of known compatible (or at least community aware working) radios? My FT-891 is working fine on the HF side of things (should be back any day now) and I'm working on my TM-281, but I'm

I wanted to use my PiDrive as it is already setup as my access point and dhcp server to my ham shack on wheels. I plugged the hat in and hooked up an external 12 volt source. When I powered it up it g