1. udrc@nw-digital-radio.groups.io

Re: Help setting up RMS Gateway? #draws #rms

Craig McVeay
 

Basil,
  Thank you for the quick reply.

results of AX.25-status
Status for direwolf.service: RUNNING and ENABLED
Status for ax25dev.service: RUNNING and ENABLED
Status for ax25dev.path: RUNNING and ENABLED
Status for ax25-mheardd.service: NOT RUNNING and ENABLED
Status for ax25d.service: NOT RUNNING and ENABLED
AX.25 device: ax0 not configured
AX.25 device: ax1 not configured

It looks like I have to configure the ports so I'll be looking for the instructions on that part.  If it helps, I'll be running an Alinco DR-135T on one side and an IC-7200 on the other.


Here are the results of ifconfig
eth0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        ether b8:27:eb:88:93:0f  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.1.59  netmask 255.255.255.0  broadcast 192.168.1.255
        inet6 fe80::85c7:f539:b08a:58a6  prefixlen 64  scopeid 0x20<link>
        ether b8:27:eb:dd:c6:5a  txqueuelen 1000  (Ethernet)
        RX packets 821  bytes 146045 (142.6 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 445  bytes 83615 (81.6 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

73,
Craig

Virus-free. www.avg.com


On Mon, Nov 4, 2019 at 11:19 AM Basil Gunn <basil@...> wrote:

Did you start AX.25?
cd
cd bin
sudo su
./ax25-start

As user pi or whatever your default user name is please post the console
output of:

ax25-status
and
ifconfig

/Basil

Craig McVeay <cmcveay@...> writes:

> Working on getting WINLINK RMS application running on my DRAWS. The image is up and running and I suspect I am nearly there but, I am a noob to Linux so I'm stuck. I went through the setup and configuration from N7NIX and here's where I am now.
>
> Setup: DRAWS HAT on RPi 3B+, 32GB Micro SD running headless. Powered through the HAT, connected to the internet via WiFi.
>
> When I run "tail -f /var/log/rms.debug", I get the following:
>
> Nov 4 08:46:01 n0csmdraws rmsgw_aci[1680]: /usr/local/bin/rmschanstat ax25 udr0 N0CSM-10 reports unavailable
> Nov 4 08:46:01 n0csmdraws rmsgw_aci[1680]: Channel: N0CSM-10 on udr0 is DOWN -- not updated
> Nov 4 08:46:01 n0csmdraws rmsgw_aci[1680]: Channel Stats: 1 read, 1 active, 1 down, 0 updated, 0 errors
> Nov 4 08:46:02 n0csmdraws rmsgw_aci[1680]: python script /usr/local/etc/rmsgw/updateversion.py failed, status 1
> Nov 4 09:17:01 n0csmdraws rmsgw_aci[3584]: N0CSM-10 - Linux RMS Gateway ACI 2.5.1 Nov 4 2019 (DM26sf)
> Nov 4 09:17:01 n0csmdraws rmsgw_aci[3584]: Channel: N0CSM-10 on udr0 (145050000 Hz, mode 0)
> Nov 4 09:17:01 n0csmdraws rmsgw_aci[3584]: /usr/local/bin/rmschanstat ax25 udr0 N0CSM-10 reports unavailable
> Nov 4 09:17:01 n0csmdraws rmsgw_aci[3584]: Channel: N0CSM-10 on udr0 is DOWN -- not updated
> Nov 4 09:17:01 n0csmdraws rmsgw_aci[3584]: Channel Stats: 1 read, 1 active, 1 down, 0 updated, 0 errors
> Nov 4 09:17:02 n0csmdraws rmsgw_aci[3584]: python script /usr/local/etc/rmsgw/updateversion.py failed, status 1
>
> I've tried two cables on each port with the same results. I'm obviously missing something but I'm not sure what.
>
> Thank you,
> Craig
> N0CSM
Join udrc@nw-digital-radio.groups.io to automatically receive all group messages.