Re: Help setting up RMS Gateway? #draws #rms


Basil Gunn
 

It looks like you didn't follow the instructions from the 'Getting
Started Guide' here:
https://nw-digital-radio.groups.io/g/udrc/wiki/DRAWS%3A-Getting-Started

You need to follow those instructions specifically:

cd
cd n7nix/config
sudo su
./app_config.sh core

This configures AX.25, Direwolf, systemd and a few other things for you.
Please read the 'Getting Started Guide'

/Basil

Craig McVeay <cmcveay@...> writes:

Basil,
Thank you for the quick reply.

*results of AX.25-status*
Status for direwolf.service: RUNNING and ENABLED
Status for ax25dev.service: RUNNING and ENABLED
Status for ax25dev.path: RUNNING and ENABLED
Status for ax25-mheardd.service: NOT RUNNING and ENABLED
Status for ax25d.service: NOT RUNNING and ENABLED
AX.25 device: ax0 not configured
AX.25 device: ax1 not configured

It looks like I have to configure the ports so I'll be looking for the
instructions on that part. If it helps, I'll be running an Alinco DR-135T
on one side and an IC-7200 on the other.


*Here are the results of ifconfig*
eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether b8:27:eb:88:93:0f txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.59 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::85c7:f539:b08a:58a6 prefixlen 64 scopeid 0x20<link>
ether b8:27:eb:dd:c6:5a txqueuelen 1000 (Ethernet)
RX packets 821 bytes 146045 (142.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 445 bytes 83615 (81.6 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

73,
Craig

<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail>
Virus-free.
www.avg.com
<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail>
<#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>

On Mon, Nov 4, 2019 at 11:19 AM Basil Gunn <@basil860> wrote:


Did you start AX.25?
cd
cd bin
sudo su
./ax25-start

As user pi or whatever your default user name is please post the console
output of:

ax25-status
and
ifconfig

/Basil

Craig McVeay <cmcveay@...> writes:

Working on getting WINLINK RMS application running on my DRAWS. The
image is up and running and I suspect I am nearly there but, I am a noob to
Linux so I'm stuck. I went through the setup and configuration from N7NIX
and here's where I am now.

Setup: DRAWS HAT on RPi 3B+, 32GB Micro SD running headless. Powered
through the HAT, connected to the internet via WiFi.

When I run "tail -f /var/log/rms.debug", I get the following:

Nov 4 08:46:01 n0csmdraws rmsgw_aci[1680]: /usr/local/bin/rmschanstat
ax25 udr0 N0CSM-10 reports unavailable
Nov 4 08:46:01 n0csmdraws rmsgw_aci[1680]: Channel: N0CSM-10 on udr0 is
DOWN -- not updated
Nov 4 08:46:01 n0csmdraws rmsgw_aci[1680]: Channel Stats: 1 read, 1
active, 1 down, 0 updated, 0 errors
Nov 4 08:46:02 n0csmdraws rmsgw_aci[1680]: python script
/usr/local/etc/rmsgw/updateversion.py failed, status 1
Nov 4 09:17:01 n0csmdraws rmsgw_aci[3584]: N0CSM-10 - Linux RMS Gateway
ACI 2.5.1 Nov 4 2019 (DM26sf)
Nov 4 09:17:01 n0csmdraws rmsgw_aci[3584]: Channel: N0CSM-10 on udr0
(145050000 Hz, mode 0)
Nov 4 09:17:01 n0csmdraws rmsgw_aci[3584]: /usr/local/bin/rmschanstat
ax25 udr0 N0CSM-10 reports unavailable
Nov 4 09:17:01 n0csmdraws rmsgw_aci[3584]: Channel: N0CSM-10 on udr0 is
DOWN -- not updated
Nov 4 09:17:01 n0csmdraws rmsgw_aci[3584]: Channel Stats: 1 read, 1
active, 1 down, 0 updated, 0 errors
Nov 4 09:17:02 n0csmdraws rmsgw_aci[3584]: python script
/usr/local/etc/rmsgw/updateversion.py failed, status 1

I've tried two cables on each port with the same results. I'm obviously
missing something but I'm not sure what.

Thank you,
Craig
N0CSM


Join udrc@nw-digital-radio.groups.io to automatically receive all group messages.