Basil,
I went back to my NWDR14 build to see if i could remember what the issue was, attached is an output file: NWDR14 Rebuild.txt
But perhaps this is all you will need to know:
#Configure core functionality
pi@asawizard:~/n7nix $ cd config
pi@asawizard:~/n7nix/config $ sudo su
root@asawizard:/home/pi/n7nix/config# ./app_config.sh core
app_config.sh: script start
Enter call sign, followed by [enter]: KO4BCV
app_config.sh: Config core
Already run 1 time(s): core config script
current dir: /home/pi/n7nix/config
Test pwd: /home/pi/n7nix/config, path: /home/pi/n7nix
Verify IF dtoverlay= is set properly
dtoverlay currently set to: dtoverlay=draws,alsaname=udrc
dtoverlay for DRAWS OK
Verify IF dtparam=audio is set properly
Last line in /boot/config.txt OK
Verify IF dtoverlay= is set properly
dtoverlay currently set to: dtoverlay=draws,alsaname=udrc
dtoverlay for DRAWS OK
Verify IF dtparam=audio is set properly
Last line in /boot/config.txt OK
app_config.sh core has already been run, exiting
-- cfg_script_name hostname: 0, passwd: 0, logfile: 0
root@asawizard:/home/pi/n7nix/config#
So despite git pull and updating and running
./app_config.sh core again, and entering my new License instead of the made up one,
i.e KO4BCZ instead of the made up one NOAPJ
I still get this:
pi@asawizard:~ $ ax25-status
Status for direwolf.service: RUNNING and ENABLED
Status for ax25dev.service: RUNNING and ENABLED
Status for ax25dev.path: RUNNING and ENABLED
Status for ax25-mheardd.service: RUNNING and ENABLED
Status for ax25d.service: RUNNING and ENABLED
AX.25 device: ax0 successfully configured with ip: 192.168.255.2
AX.25 device: ax1 successfully configured with ip: 192.168.255.3
pi@asawizard:~ $ tail -f /var/log/direwolf/direwolf.log
Jan 26 20:10:51 asawizard direwolf[455]: KISS protocol set TXtail = 10 (*10mS units = 100 mS), port 1
Jan 26 20:10:51 asawizard direwolf[455]: KISS protocol set Persistence = 32, port 1
Jan 26 20:10:51 asawizard direwolf[455]: KISS protocol set SlotTime = 20 (*10mS units = 200 mS), port 1
Jan 26 20:10:51 asawizard direwolf[455]: KISS protocol set FullDuplex = 0, port 1
Jan 26 20:10:56 asawizard direwolf[455]: Can't get address for IGate server
noam.aprs2.net, Temporary failure in name resolution
Jan 26 20:11:01 asawizard direwolf[455]: Can't get address for IGate server
noam.aprs2.net, Temporary failure in name resolution
Jan 26 20:11:06 asawizard direwolf[455]: Now connected to IGate server
noam.aprs2.net (167.114.2.176)
Jan 26 20:11:06 asawizard direwolf[455]: Check server status here
http://167.114.2.176:14501Jan 26 20:11:11 asawizard direwolf[455]: [ig] # aprsc 2.1.5-g8af3cdc
Jan 26 20:11:11 asawizard direwolf[455]: [ig] # logresp N0APJ verified, server T2CAWEST
So as you see having alread run the core config once it did not prompt me for my passcode and did not change the original entry.
I am unable to find the direwolf.conf file to edit it for the correct info. perhaps that will suffice. The
APRS.SI site is receiving
Is feasible to try to correct NOAPJ with KO4BCZ or should I just bite the bullet and start fresh with the NWDR15 image.
A complete output txt file is attached anticipating other questions.
Paul KO4BCZ