Re: #audio #install #config #wsjtx #install #audio #wsjtx #config


Erwin OE1EKG
 

Hi Basil,

thanks for the hint. So it is a language problem :-) I changed the language on the raspberry pi from German to English to avoid future problems with tolls and language. Here is the output and below the bug info - no idea what the errors in the boot fail check are. I went through the installation but without to config the packet part now. I can not check the audio with my KX3 cause I'm waiting for the cables.

The error in wsjtx is a known one, now I can start it:
WSJT-X release 2.3.0 will give an error on startup with a message about the en_US.UTF-8 locale not being found. This is because a default install of Raspberry Pi OS has very few locales installed. This is easily rectified by the following two lines executed on a terminal:

sudo sed -i "s/# en_US.UTF-8/en_US.UTF-8/g" /etc/locale.gen

sudo locale-gen



pi@draws:~ $ alsa-show.sh
 ==== List All sound card device names (3)
card 0: b1 [bcm2835 HDMI 1]
card 1: Headphones [bcm2835 Headphones]
card 2: udrc [udrc]
 
 ======= DRAWS
 ===== ALSA Controls for Radio Transmit =====
LO Driver Gain  L:[-6.00dB] R:[-6.00dB]
PCM        L:[-25.00dB] R:[-25.00dB]
DAC Playback PT L:[P3] R:[P3]
LO Playback CM [Full Chip]
 
 ===== ALSA Controls for Radio Receive =====
ADC Level L:[0.00dB] R:[0.00dB]
IN1 L:[Off] R:[Off]
IN2 L:[10 kOhm] R:[10 kOhm]
CM L:[10 kOhm] R:[10 kOhm]


pi@draws:~ $ buginfo.sh
=== Versions ===
== Kernel:
Linux draws 5.4.79-v7l+ #1373 SMP Mon Nov 23 13:27:40 GMT 2020 armv7l GNU/Linux
 
== Firmware:
Nov 30 2020 22:12:08 
Copyright (c) 2012 Broadcom
version ab1181cc0cb6df52bfae3b1d3fef0ce7c325166c (clean) (release) (start)
 
== Pi hardware:
 Pi 4 Model B, Rev 1.4, 8GB mem, Mfg by Sony UK with WiFi
temp=45.2'C
 
== DRAWS hardware:
Product id: 0x0004, ver: 0x0108, Assembly rev: 1, fab rev: 8
 
=== Checks ===
== Codec driver check:
[    3.902129] asoc-simple-card soc:sound: tlv320aic32x4-hifi <-> fe203000.i2s mapping ok
 
== DRAWS driver check:
udrc card number line: card 2: udrc [udrc], device 0: bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4-hifi-0 [bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4-hifi-0]
udrc is sound card #2
 
== Boot 'fail' check:
[    0.530501] bcmgenet fd580000.ethernet: failed to get enet clock
[    0.530520] bcmgenet fd580000.ethernet: failed to get enet-wol clock
[    0.530529] bcmgenet fd580000.ethernet: failed to get enet-eee clock
[    3.650250] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.raspberrypi,4-model-b.txt failed with error -2
 
== GPS check:
Serial devices OK
gpsd OK
 
== /boot/config file
hdmi_force_hotplug=1
hdmi_group=2
hdmi_mode=82
[pi4]
dtoverlay=vc4-fkms-v3d
[all]
dtoverlay=
dtoverlay=draws,alsaname=udrc
force_turbo=1
dtparam=audio=on
 

Join udrc@nw-digital-radio.groups.io to automatically receive all group messages.