Date   

Re: Cant turn off direwolf and ax25 #configuration #management #draws #direwolf #ax25

Art - KC7SDA
 

as an fyi you don't NEED ax25 to run direwolf, I never installed the AX.25 stack on any of my ham computers and I can still run direwolf and xastir perfectly fine


Re: Cant turn off direwolf and ax25 #configuration #management #draws #direwolf #ax25

Basil Gunn
 

Read this:
https://github.com/nwdigitalradio/n7nix/blob/master/DRAWS_CONFIG.md

The step where you run

app_config.sh core

setups up your image & starts direwolf from systemd.
If you read to the bottom of the document you will learn the proper way
to stop & disable direwolf and the ax.25 stack.

Using killall leaves the ax.25 stack compromised and will give
unpredictable results later on.

/Basil

Bob Orrett <boborrett@gmail.com> writes:

Thanks for the killall direwolf suggestion but I seem to have deeper
issues. The response to that command was "direwolf: no process found"
I have downloaded the Draws beta6 image about 3 or 4 times on different sd
cards and direwolf does not seem to run, among other things. I do get the
usual desktop for rspbian stretch. Everything looks great. Ft8 and jso call
will not work. I have had them working before and I have made no other
changes to the setup except a new image burned onto ghe sd card. I am at a
loss. Must be the way I am burning it to the sd card. I am using etcher on
windows 10.
Bob ve3obo

On Tue, Dec 25, 2018, 12:35 f6bvp <f6bvp@free.fr wrote:

I noticed that killing direwolf on Compass Linux beta 1.5, ax.25
interface udr0 and udr1 are removed freeing access to draws sound card.

sudo killall direwolf

is a quite simple command indeed.

Bernard, f6bvp
Le 24/12/2018 à 04:48, Bob Orrett a écrit :

I am a newbie to RPi and linux.
I have the beta6 installed and running. I cannot seem to be able to stop
direwolf and ax25 so that ft8 and js8call will get access to the draws
sound card.
I entered

cd
cd bin
sudo su
./ax25-stop

The pi returns the command prompt but not anything like "ax25 has stopped".
I see the correct sound card input and output codec in the settings for
these programs (ft8 and js8call) but no audio from the ft817 radio. I had
this working before. What am I missing?

Bob ve3obo



On Sun, Dec 23, 2018, 18:59 Basil Gunn <basil@pacabunga.com wrote:


Before you update your image capture your current alsamixer settings
somewhere. Just run ./n7nix/bin/alsa-show.sh & make a copy of result.

Latest image current_beta.zip has been updated to draws_beta6.zip

http://images.nwdigitalradio.com/

List of changes since draws_beta5.zip

313d362 - n7nix, 22 hours ago : Explicity describe port names to use with
beacon command.
e3264e2 - n7nix, 22 hours ago : Document default login & password.
95d9aa3 - n7nix, 22 hours ago : Make a default hostname to handle CR only
at hostname prompt.
1f2ad74 - n7nix, 25 hours ago : Set default ADC Level to zero.
aa04a73 - n7nix, 26 hours ago : Add ax.25 ip address prompt & change
default addresses.
dcdd59f - n7nix, 26 hours ago : Enable log of measurements, statistics &
tracking.
3c78e73 - n7nix, 26 hours ago : Fix 'completed' log file entry
57c63aa - n7nix, 2 days ago : Define MODE_9600_ENABLE
68ef2d9 - n7nix, 2 days ago : Set default LO Driver Gain to be more
generic.
fb0beff - n7nix, 2 days ago : Display right & left inputs on a single
line, add debug option.
1de12a3 - n7nix, 2 days ago : Add adjustment of chrony controlled clock.
d13df5d - n7nix, 2 days ago : Move to local bin & add input control
display.
d816ff6 - n7nix, 2 days ago : Fix routing of AFOUT & DISCOUT for default
case.
95ab064 - n7nix, 4 days ago : Add Test RPi sound section.
56d3978 - n7nix, 4 days ago : Add description on enabling onboard sound
function.
134acd9 - n7nix, 4 days ago : Add display of alsa controls.
0d7715a - n7nix, 4 days ago : Update jscall to latest version.
337bdad - n7nix, 4 days ago : Add description on enabling onboard sound
function.
ad0ba74 - n7nix, 4 days ago : Add comments for copying files.
cc88f97 - n7nix, 5 days ago : Add script to collect data on the chrony
daemon.
4f4d1c5 - n7nix, 5 days ago : Add more notes on debugging chrony.
ad44b8f - n7nix, 5 days ago : Add links to the image files.
b36acc7 - n7nix, 5 days ago : Update program installatin table.
95fede5 - n7nix, 5 days ago : Add table of installed programs for DRAWS
image.
8848971 - n7nix, 5 days ago : Fixes for iptables install.
183b3d2 - n7nix, 6 days ago : Add iptables install/config in core config.
e90b7bb - n7nix, 6 days ago : Fix variable USER not being set in BIN_DIR
deee5fe - n7nix, 6 days ago : Add description to verify direwolf is
running.
4f5da24 - n7nix, 6 days ago : A DRAWS to ptt GPIO table.
77d1d10 - n7nix, 6 days ago : Include port name in beacon & message.
4b4f507 - n7nix, 6 days ago : Change connector name to left & right.
835a480 - n7nix, 6 days ago : Explicitly set left & right channel GPIO
for DRAWS.
f683948 - n7nix, 6 days ago : Exit script if direwolf already running.
372d9f5 - n7nix, 7 days ago : Check for compass default password &
prompt to change.

/Basil



Bernard, F6BVPhttp://f6bvp.org
--
Si vous ne souhaitez plus recevoir d'informations de la part du projet
"Le chant des étoiles" de l'association Dimension Parabole
envoyez un courriel à f6bvp@free.fr avec comme sujet :
me désinscrire de la liste de diffusion Dimension Parabole.http://radiotelescope-lavillette.fr



Re: Cant turn off direwolf and ax25 #configuration #management #draws #direwolf #ax25

Bob Orrett <boborrett@...>
 

I hate to admit this but I don't know what is meant by "run Basil's scripts"
Was I supposed to do something after the first boot up of beta6 ? Everything looks normal after the boot up.  Exceot ft8 and js8call do not get access to the soundcard and I cannot seem to stop or start direwolf. 
Bob ve3obo


Re: Cant turn off direwolf and ax25 #configuration #management #draws #direwolf #ax25

Bob Orrett <boborrett@...>
 

Thanks for the killall direwolf suggestion but I seem to have deeper issues. The response to that command was "direwolf: no process found"
I have downloaded the Draws beta6 image about 3 or 4 times on different sd cards and direwolf does not seem to run,  among other things. I do get the usual desktop for rspbian stretch. Everything looks great. Ft8 and jso call will not work. I have had them working before and I have made no other changes to the setup except a new image burned onto ghe sd card. I am at a loss. Must be the way I am burning it to the sd card. I am using etcher on windows 10.
Bob ve3obo

On Tue, Dec 25, 2018, 12:35 f6bvp <f6bvp@... wrote:

I noticed that killing direwolf on Compass Linux beta 1.5,  ax.25 interface udr0 and udr1 are removed freeing access to draws sound card.

sudo killall direwolf

is a quite simple command indeed.

Bernard, f6bvp

Le 24/12/2018 à 04:48, Bob Orrett a écrit :
I am a newbie to RPi and linux. 
I have the beta6 installed and running. I cannot seem to be able to stop direwolf and ax25 so that ft8 and js8call will get access to the draws sound card.
I entered

cd 
cd bin
sudo su 
./ax25-stop 

The pi returns the command prompt but not anything like "ax25 has stopped".
I see the correct sound card input and output codec in the settings for these programs (ft8 and js8call) but no audio from the ft817 radio. I had this working before. What am I missing?

Bob ve3obo



On Sun, Dec 23, 2018, 18:59 Basil Gunn <basil@... wrote:

Before you update your image capture your current alsamixer settings
somewhere.  Just run ./n7nix/bin/alsa-show.sh & make a copy of result.

Latest image current_beta.zip has been updated to draws_beta6.zip

http://images.nwdigitalradio.com/

List of changes since draws_beta5.zip

313d362 - n7nix, 22 hours ago : Explicity describe port names to use with beacon command.
e3264e2 - n7nix, 22 hours ago : Document default login & password.
95d9aa3 - n7nix, 22 hours ago : Make a default hostname to handle CR only at hostname prompt.
1f2ad74 - n7nix, 25 hours ago : Set default ADC Level to zero.
aa04a73 - n7nix, 26 hours ago : Add ax.25 ip address prompt & change default addresses.
dcdd59f - n7nix, 26 hours ago : Enable log of measurements, statistics & tracking.
3c78e73 - n7nix, 26 hours ago : Fix 'completed' log file entry
57c63aa - n7nix, 2 days ago : Define MODE_9600_ENABLE
68ef2d9 - n7nix, 2 days ago : Set default LO Driver Gain to be more generic.
fb0beff - n7nix, 2 days ago : Display right & left inputs on a single line, add debug option.
1de12a3 - n7nix, 2 days ago : Add adjustment of chrony controlled clock.
d13df5d - n7nix, 2 days ago : Move to local bin & add input control display.
d816ff6 - n7nix, 2 days ago : Fix routing of AFOUT & DISCOUT for default case.
95ab064 - n7nix, 4 days ago : Add Test RPi sound section.
56d3978 - n7nix, 4 days ago : Add description on enabling onboard sound function.
134acd9 - n7nix, 4 days ago : Add display of alsa controls.
0d7715a - n7nix, 4 days ago : Update jscall to latest version.
337bdad - n7nix, 4 days ago : Add description on enabling onboard sound function.
ad0ba74 - n7nix, 4 days ago : Add comments for copying files.
cc88f97 - n7nix, 5 days ago : Add script to collect data on the chrony daemon.
4f4d1c5 - n7nix, 5 days ago : Add more notes on debugging chrony.
ad44b8f - n7nix, 5 days ago : Add links to the image files.
b36acc7 - n7nix, 5 days ago : Update program installatin table.
95fede5 - n7nix, 5 days ago : Add table of installed programs for DRAWS image.
8848971 - n7nix, 5 days ago : Fixes for iptables install.
183b3d2 - n7nix, 6 days ago : Add iptables install/config in core config.
e90b7bb - n7nix, 6 days ago : Fix variable USER not being set in BIN_DIR
deee5fe - n7nix, 6 days ago : Add description to verify direwolf is running.
4f5da24 - n7nix, 6 days ago : A DRAWS to ptt GPIO table.
77d1d10 - n7nix, 6 days ago : Include port name in beacon & message.
4b4f507 - n7nix, 6 days ago : Change connector name to left & right.
835a480 - n7nix, 6 days ago : Explicitly set left & right channel GPIO for DRAWS.
f683948 - n7nix, 6 days ago : Exit script if direwolf already running.
372d9f5 - n7nix, 7 days ago : Check for compass default password &
prompt to change.

/Basil



Bernard, F6BVP
http://f6bvp.org
-- 
Si vous ne souhaitez plus recevoir d'informations de la part du projet
"Le chant des étoiles" de l'association Dimension Parabole
envoyez un courriel à f6bvp@... avec comme sujet :
me désinscrire de la liste de diffusion Dimension Parabole.
http://radiotelescope-lavillette.fr


Re: Cant turn off direwolf and ax25 #configuration #management #draws #direwolf #ax25

Jack Spitznagel
 

Hi Basil,

Thanks! That will help.

Jack

-----Original Message-----
From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Basil Gunn
Sent: Tuesday, December 25, 2018 14:58
To: udrc@nw-digital-radio.groups.io
Subject: Re: [udrc] Cant turn off direwolf and ax25


Hi Jack,

As it was in Beta 5, having Basil’s scripts scattered between ~/bin,
~/n7nix/bin, and ~/n7nix/debug made doing the set up and testing a bit
of a challenge. Jumping around the different pieces of the directory
tree made for some interesting “not found” errors.
In the beta6 image after you have run the app_config.sh core script most of the commonly used scripts are copied to the local bin, ~/bin and that will be in your PATH if you are logged in as user pi. So you only need to type the name of the script. If you are required to be root then
just:
cd /home/pi/bin
./<name_of_the_script>

/Basil


Good work guys! We really appreciate what you are doing.

Jack – KD4IZ



From: udrc@nw-digital-radio.groups.io
<udrc@nw-digital-radio.groups.io> On Behalf Of John D Hays - K7VE
Sent: Tuesday, December 25, 2018 12:38
To: udrc@nw-digital-radio.groups.io
Subject: Re: [udrc] Cant turn off direwolf and ax25



This will leave the AX.25 stack in a weird state, please use Basil's
scripts to start and stop AX.25 and it will start/stop direwolf.





--
J Spitznagel
Science River LLC
KD4IZ


Re: Cant turn off direwolf and ax25 #configuration #management #draws #direwolf #ax25

Basil Gunn
 

Hi Jack,

As it was in Beta 5, having Basil’s scripts scattered between ~/bin,
~/n7nix/bin, and ~/n7nix/debug made doing the set up and testing a bit
of a challenge. Jumping around the different pieces of the directory
tree made for some interesting “not found” errors.
In the beta6 image after you have run the app_config.sh core script most
of the commonly used scripts are copied to the local bin, ~/bin and that
will be in your PATH if you are logged in as user pi. So you only need
to type the name of the script. If you are required to be root then
just:
cd /home/pi/bin
./<name_of_the_script>

/Basil


Good work guys! We really appreciate what you are doing.

Jack – KD4IZ



From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of John D Hays - K7VE
Sent: Tuesday, December 25, 2018 12:38
To: udrc@nw-digital-radio.groups.io
Subject: Re: [udrc] Cant turn off direwolf and ax25



This will leave the AX.25 stack in a weird state, please use Basil's
scripts to start and stop AX.25 and it will start/stop direwolf.


Re: Cant turn off direwolf and ax25 #configuration #management #draws #direwolf #ax25

Jack Spitznagel
 

John and Basil,

 

Good point on the appropriate scripts (not just killing direwolf)! I will be loading Beta 6 later today…

 

Suggestion: Is there any way these script functions can be put into/called by a “DRAWS/udrc control panel” app?

 

As it was in Beta 5, having Basil’s scripts scattered between ~/bin, ~/n7nix/bin, and ~/n7nix/debug made doing the set up and testing a bit of a challenge. Jumping around the different pieces of the directory tree made for some interesting “not found” errors.

 

Good work guys! We really appreciate what you are doing.

 

Jack – KD4IZ

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of John D Hays - K7VE
Sent: Tuesday, December 25, 2018 12:38
To: udrc@nw-digital-radio.groups.io
Subject: Re: [udrc] Cant turn off direwolf and ax25

 

This will leave the AX.25 stack in a weird state, please use Basil's scripts to start and stop AX.25 and it will start/stop direwolf.

 

If you start direwolf without AX.25, then it can be stopped without AX.25

 

On Tue, Dec 25, 2018 at 9:35 AM f6bvp <f6bvp@...> wrote:

I noticed that killing direwolf on Compass Linux beta 1.5,  ax.25 interface udr0 and udr1 are removed freeing access to draws sound card.

sudo killall direwolf

is a quite simple command indeed.

Bernard, f6bvp

Le 24/12/2018 à 04:48, Bob Orrett a écrit :

I am a newbie to RPi and linux. 

I have the beta6 installed and running. I cannot seem to be able to stop direwolf and ax25 so that ft8 and js8call will get access to the draws sound card.

I entered

 

cd 

cd bin

sudo su 

./ax25-stop 

 

The pi returns the command prompt but not anything like "ax25 has stopped".

I see the correct sound card input and output codec in the settings for these programs (ft8 and js8call) but no audio from the ft817 radio. I had this working before. What am I missing?

 

Bob ve3obo

 

 

On Sun, Dec 23, 2018, 18:59 Basil Gunn <basil@... wrote:


Before you update your image capture your current alsamixer settings
somewhere.  Just run ./n7nix/bin/alsa-show.sh & make a copy of result.

Latest image current_beta.zip has been updated to draws_beta6.zip

http://images.nwdigitalradio.com/

List of changes since draws_beta5.zip

313d362 - n7nix, 22 hours ago : Explicity describe port names to use with beacon command.
e3264e2 - n7nix, 22 hours ago : Document default login & password.
95d9aa3 - n7nix, 22 hours ago : Make a default hostname to handle CR only at hostname prompt.
1f2ad74 - n7nix, 25 hours ago : Set default ADC Level to zero.
aa04a73 - n7nix, 26 hours ago : Add ax.25 ip address prompt & change default addresses.
dcdd59f - n7nix, 26 hours ago : Enable log of measurements, statistics & tracking.
3c78e73 - n7nix, 26 hours ago : Fix 'completed' log file entry
57c63aa - n7nix, 2 days ago : Define MODE_9600_ENABLE
68ef2d9 - n7nix, 2 days ago : Set default LO Driver Gain to be more generic.
fb0beff - n7nix, 2 days ago : Display right & left inputs on a single line, add debug option.
1de12a3 - n7nix, 2 days ago : Add adjustment of chrony controlled clock.
d13df5d - n7nix, 2 days ago : Move to local bin & add input control display.
d816ff6 - n7nix, 2 days ago : Fix routing of AFOUT & DISCOUT for default case.
95ab064 - n7nix, 4 days ago : Add Test RPi sound section.
56d3978 - n7nix, 4 days ago : Add description on enabling onboard sound function.
134acd9 - n7nix, 4 days ago : Add display of alsa controls.
0d7715a - n7nix, 4 days ago : Update jscall to latest version.
337bdad - n7nix, 4 days ago : Add description on enabling onboard sound function.
ad0ba74 - n7nix, 4 days ago : Add comments for copying files.
cc88f97 - n7nix, 5 days ago : Add script to collect data on the chrony daemon.
4f4d1c5 - n7nix, 5 days ago : Add more notes on debugging chrony.
ad44b8f - n7nix, 5 days ago : Add links to the image files.
b36acc7 - n7nix, 5 days ago : Update program installatin table.
95fede5 - n7nix, 5 days ago : Add table of installed programs for DRAWS image.
8848971 - n7nix, 5 days ago : Fixes for iptables install.
183b3d2 - n7nix, 6 days ago : Add iptables install/config in core config.
e90b7bb - n7nix, 6 days ago : Fix variable USER not being set in BIN_DIR
deee5fe - n7nix, 6 days ago : Add description to verify direwolf is running.
4f5da24 - n7nix, 6 days ago : A DRAWS to ptt GPIO table.
77d1d10 - n7nix, 6 days ago : Include port name in beacon & message.
4b4f507 - n7nix, 6 days ago : Change connector name to left & right.
835a480 - n7nix, 6 days ago : Explicitly set left & right channel GPIO for DRAWS.
f683948 - n7nix, 6 days ago : Exit script if direwolf already running.
372d9f5 - n7nix, 7 days ago : Check for compass default password &
prompt to change.

/Basil


Bernard, F6BVP
http://f6bvp.org
-- 
Si vous ne souhaitez plus recevoir d'informations de la part du projet
"Le chant des étoiles" de l'association Dimension Parabole
envoyez un courriel à f6bvp@... avec comme sujet :
me désinscrire de la liste de diffusion Dimension Parabole.
http://radiotelescope-lavillette.fr


 

--

 


John D. Hays
Edmonds, WA

K7VE

 

   

 


--
J Spitznagel
Science River LLC
KD4IZ


Re: Cant turn off direwolf and ax25 #configuration #management #draws #direwolf #ax25

 

This will leave the AX.25 stack in a weird state, please use Basil's scripts to start and stop AX.25 and it will start/stop direwolf.

If you start direwolf without AX.25, then it can be stopped without AX.25

On Tue, Dec 25, 2018 at 9:35 AM f6bvp <f6bvp@...> wrote:

I noticed that killing direwolf on Compass Linux beta 1.5,  ax.25 interface udr0 and udr1 are removed freeing access to draws sound card.

sudo killall direwolf

is a quite simple command indeed.

Bernard, f6bvp

Le 24/12/2018 à 04:48, Bob Orrett a écrit :
I am a newbie to RPi and linux. 
I have the beta6 installed and running. I cannot seem to be able to stop direwolf and ax25 so that ft8 and js8call will get access to the draws sound card.
I entered

cd 
cd bin
sudo su 
./ax25-stop 

The pi returns the command prompt but not anything like "ax25 has stopped".
I see the correct sound card input and output codec in the settings for these programs (ft8 and js8call) but no audio from the ft817 radio. I had this working before. What am I missing?

Bob ve3obo



On Sun, Dec 23, 2018, 18:59 Basil Gunn <basil@... wrote:

Before you update your image capture your current alsamixer settings
somewhere.  Just run ./n7nix/bin/alsa-show.sh & make a copy of result.

Latest image current_beta.zip has been updated to draws_beta6.zip

http://images.nwdigitalradio.com/

List of changes since draws_beta5.zip

313d362 - n7nix, 22 hours ago : Explicity describe port names to use with beacon command.
e3264e2 - n7nix, 22 hours ago : Document default login & password.
95d9aa3 - n7nix, 22 hours ago : Make a default hostname to handle CR only at hostname prompt.
1f2ad74 - n7nix, 25 hours ago : Set default ADC Level to zero.
aa04a73 - n7nix, 26 hours ago : Add ax.25 ip address prompt & change default addresses.
dcdd59f - n7nix, 26 hours ago : Enable log of measurements, statistics & tracking.
3c78e73 - n7nix, 26 hours ago : Fix 'completed' log file entry
57c63aa - n7nix, 2 days ago : Define MODE_9600_ENABLE
68ef2d9 - n7nix, 2 days ago : Set default LO Driver Gain to be more generic.
fb0beff - n7nix, 2 days ago : Display right & left inputs on a single line, add debug option.
1de12a3 - n7nix, 2 days ago : Add adjustment of chrony controlled clock.
d13df5d - n7nix, 2 days ago : Move to local bin & add input control display.
d816ff6 - n7nix, 2 days ago : Fix routing of AFOUT & DISCOUT for default case.
95ab064 - n7nix, 4 days ago : Add Test RPi sound section.
56d3978 - n7nix, 4 days ago : Add description on enabling onboard sound function.
134acd9 - n7nix, 4 days ago : Add display of alsa controls.
0d7715a - n7nix, 4 days ago : Update jscall to latest version.
337bdad - n7nix, 4 days ago : Add description on enabling onboard sound function.
ad0ba74 - n7nix, 4 days ago : Add comments for copying files.
cc88f97 - n7nix, 5 days ago : Add script to collect data on the chrony daemon.
4f4d1c5 - n7nix, 5 days ago : Add more notes on debugging chrony.
ad44b8f - n7nix, 5 days ago : Add links to the image files.
b36acc7 - n7nix, 5 days ago : Update program installatin table.
95fede5 - n7nix, 5 days ago : Add table of installed programs for DRAWS image.
8848971 - n7nix, 5 days ago : Fixes for iptables install.
183b3d2 - n7nix, 6 days ago : Add iptables install/config in core config.
e90b7bb - n7nix, 6 days ago : Fix variable USER not being set in BIN_DIR
deee5fe - n7nix, 6 days ago : Add description to verify direwolf is running.
4f5da24 - n7nix, 6 days ago : A DRAWS to ptt GPIO table.
77d1d10 - n7nix, 6 days ago : Include port name in beacon & message.
4b4f507 - n7nix, 6 days ago : Change connector name to left & right.
835a480 - n7nix, 6 days ago : Explicitly set left & right channel GPIO for DRAWS.
f683948 - n7nix, 6 days ago : Exit script if direwolf already running.
372d9f5 - n7nix, 7 days ago : Check for compass default password &
prompt to change.

/Basil



Bernard, F6BVP
http://f6bvp.org
-- 
Si vous ne souhaitez plus recevoir d'informations de la part du projet
"Le chant des étoiles" de l'association Dimension Parabole
envoyez un courriel à f6bvp@... avec comme sujet :
me désinscrire de la liste de diffusion Dimension Parabole.
http://radiotelescope-lavillette.fr



--


John D. Hays
Edmonds, WA
K7VE

   


Re: Cant turn off direwolf and ax25 #configuration #management #draws #direwolf #ax25

Bernard f6bvp / ai7bg
 

I noticed that killing direwolf on Compass Linux beta 1.5,  ax.25 interface udr0 and udr1 are removed freeing access to draws sound card.

sudo killall direwolf

is a quite simple command indeed.

Bernard, f6bvp

Le 24/12/2018 à 04:48, Bob Orrett a écrit :
I am a newbie to RPi and linux. 
I have the beta6 installed and running. I cannot seem to be able to stop direwolf and ax25 so that ft8 and js8call will get access to the draws sound card.
I entered

cd 
cd bin
sudo su 
./ax25-stop 

The pi returns the command prompt but not anything like "ax25 has stopped".
I see the correct sound card input and output codec in the settings for these programs (ft8 and js8call) but no audio from the ft817 radio. I had this working before. What am I missing?

Bob ve3obo



On Sun, Dec 23, 2018, 18:59 Basil Gunn <basil@... wrote:

Before you update your image capture your current alsamixer settings
somewhere.  Just run ./n7nix/bin/alsa-show.sh & make a copy of result.

Latest image current_beta.zip has been updated to draws_beta6.zip

http://images.nwdigitalradio.com/

List of changes since draws_beta5.zip

313d362 - n7nix, 22 hours ago : Explicity describe port names to use with beacon command.
e3264e2 - n7nix, 22 hours ago : Document default login & password.
95d9aa3 - n7nix, 22 hours ago : Make a default hostname to handle CR only at hostname prompt.
1f2ad74 - n7nix, 25 hours ago : Set default ADC Level to zero.
aa04a73 - n7nix, 26 hours ago : Add ax.25 ip address prompt & change default addresses.
dcdd59f - n7nix, 26 hours ago : Enable log of measurements, statistics & tracking.
3c78e73 - n7nix, 26 hours ago : Fix 'completed' log file entry
57c63aa - n7nix, 2 days ago : Define MODE_9600_ENABLE
68ef2d9 - n7nix, 2 days ago : Set default LO Driver Gain to be more generic.
fb0beff - n7nix, 2 days ago : Display right & left inputs on a single line, add debug option.
1de12a3 - n7nix, 2 days ago : Add adjustment of chrony controlled clock.
d13df5d - n7nix, 2 days ago : Move to local bin & add input control display.
d816ff6 - n7nix, 2 days ago : Fix routing of AFOUT & DISCOUT for default case.
95ab064 - n7nix, 4 days ago : Add Test RPi sound section.
56d3978 - n7nix, 4 days ago : Add description on enabling onboard sound function.
134acd9 - n7nix, 4 days ago : Add display of alsa controls.
0d7715a - n7nix, 4 days ago : Update jscall to latest version.
337bdad - n7nix, 4 days ago : Add description on enabling onboard sound function.
ad0ba74 - n7nix, 4 days ago : Add comments for copying files.
cc88f97 - n7nix, 5 days ago : Add script to collect data on the chrony daemon.
4f4d1c5 - n7nix, 5 days ago : Add more notes on debugging chrony.
ad44b8f - n7nix, 5 days ago : Add links to the image files.
b36acc7 - n7nix, 5 days ago : Update program installatin table.
95fede5 - n7nix, 5 days ago : Add table of installed programs for DRAWS image.
8848971 - n7nix, 5 days ago : Fixes for iptables install.
183b3d2 - n7nix, 6 days ago : Add iptables install/config in core config.
e90b7bb - n7nix, 6 days ago : Fix variable USER not being set in BIN_DIR
deee5fe - n7nix, 6 days ago : Add description to verify direwolf is running.
4f5da24 - n7nix, 6 days ago : A DRAWS to ptt GPIO table.
77d1d10 - n7nix, 6 days ago : Include port name in beacon & message.
4b4f507 - n7nix, 6 days ago : Change connector name to left & right.
835a480 - n7nix, 6 days ago : Explicitly set left & right channel GPIO for DRAWS.
f683948 - n7nix, 6 days ago : Exit script if direwolf already running.
372d9f5 - n7nix, 7 days ago : Check for compass default password &
prompt to change.

/Basil



Bernard, F6BVP
http://f6bvp.org
-- 
Si vous ne souhaitez plus recevoir d'informations de la part du projet
"Le chant des étoiles" de l'association Dimension Parabole
envoyez un courriel à f6bvp@... avec comme sujet :
me désinscrire de la liste de diffusion Dimension Parabole.
http://radiotelescope-lavillette.fr


Re: Cant turn off direwolf and ax25 #configuration #management #draws #direwolf #ax25

Bob Orrett <boborrett@...>
 

Good idea. I will do that. 
Merry Christmas
Ve3obo

On Tue, Dec 25, 2018, 00:29 Art Olson <olson339@... wrote:
Bob

Can’t speak for this implementation as I am waiting for the next DRAW run to be shipped. However my experience with other rpi implementations, my SD card contained a single image. I make sure by reformatting with SD formatter then burn image with etcher. You could try this approach. 

FWIW

Art


On Dec 24, 2018, at 8:58 PM, Bob Orrett <boborrett@...> wrote:

Merry Christmas,  Basil.
I dont expect to hear back from you for a few days.
I am trying to get wsjtx and js8call running. I did have this working so I know the 817 radio is ok. I could not use the supplied cables but I have an alternate cable that worked. However, now, with a new image burned, I cannot get the audio part to work. I do see the correct codec in settings for wsjtx and js8call but not audio appears. I
As you suggested, I tried stating direwolf with ./ax25-start but I get this message
A dependance job for ax25-mheardd.. service failed. See 'journalctl -xe' for details.
I did run journalctl -xe and got a full page report. I can screen capture it but I have no idea how to send it to you.
In red it says "Failed to start AX25 device"

So there must be something wrong with my new image but I have tried several times. 
I did notice that the one time it did work, on first bootup ,I was asked a few questions before it went to the standard desktop. I have never been asked since for anything, no passwords, no timezone, etc, for any new image I have tried, either bata5 or beta5. It just goes directly to the standard desktop upon bootup. Even first time. To burn the image i download zipped file from your download page. Then unzip with windows 10 then burn to the sd card with Etcher. I usually just burn onto the same sd card that had the previous burn. Am I doing this correctly? Does it matter that the sd card was not empty when I burn onto it?
I will try another burn with a new download. 

Btw my return on journalctl -xe also said 
Error setting device : ax0 parks

Same for ax1

Hope that's enough info
Bob ve3obo

On Mon, Dec 24, 2018, 01:21 Basil Gunn <basil@... wrote:

if direwolf & ax-25 are already stopped then running ./ax25-stop does
not respond with anything.

type pidof direwolf
if no process id is printed direwolf is not running

try starting & stopping it.
./ax25-start
./ax25-stop

Is your radio set for AFOUT or DISCOUT?
 - On your radio what is Menu #39 (PKT MIC) set to?
 - On your radio what is Menu #40 (PKT RATE) set to?
Are you using VHF/UHF or HF?
Which audio port are you using left or right?

Send me the console output of
cd
cd bin
./showudrc.sh
./alsa-show.sh

draws-beta5 image defaulted to using DISCOUT (IN1)
draws-beta6 image defaults to using AFOUT (IN2)

/Basil

Bob Orrett <boborrett@...> writes:

> I am a newbie to RPi and linux.
> I have the beta6 installed and running. I cannot seem to be able to stop
> direwolf and ax25 so that ft8 and js8call will get access to the draws
> sound card.
> I entered
>
> cd
> cd bin
> sudo su
> ./ax25-stop
>
> The pi returns the command prompt but not anything like "ax25 has stopped".
> I see the correct sound card input and output codec in the settings for
> these programs (ft8 and js8call) but no audio from the ft817 radio. I had
> this working before. What am I missing?
>
> Bob ve3obo




Re: amixer questions Re: Set Up Issues #setup #fldigi #draws

Joseph Vilardo
 

Merry Christmas Julian

All of the adjustment I made to the receive signal was through the ADC Level of the alsa mixer. FLDIGI has a go no go "diamond shaped" icon on the bottom tool bar of the main screen.   It lights up "black" for low receive audio, "Green" for ok and "Red" for over driven receive. The ADC Level adjustment got the green diamond to light with plenty of room to spare.

Joe K3JV

On 12/25/2018 2:32 AM, Julian OH8STN wrote:
Excellent write up Joe.
Did you adjust any other setting than adjusting ADC level in alsamixer for receive level?

Outstanding post. 
Thanks for sharing 


On 25 Dec 2018 05:13, Joseph Vilardo <jvilardo@...> wrote:

Gents

I wanted to share the good news of having success with the Beta6 image of draws with Direwolf ,  YAAC and a leap today with fldigi running on a Kenwood TM-V71 dual bander.

I downloaded the beta 6 image today and ran through Basil's "Verify_Config.md". I found a  notation symbol that gave me trouble until I changed it.

Under "check ALSA settings for deviation " instructions go as follows:

cd  ~/n7nix/debug

~/alsa-show.sh

I  removing the tilde and the ~/ for the line alsa-show.sh after trying the command as noted several times and then it ran fine.

At first I couldn't get fldigi to allow me to select udrc under the sound card configuration. It just wasn't there. During the Verify_Config.md the instructions required two changes in the /boot/config.txt to test analog audio un comment, remove the # from dtparam=audio=on and /boot/config.txt  hdmi_drive=2 when your done with the Verify_Config.md make sure you go back to /boot/config.txt and comment out, put the # at the beginning of the lines #dtparam=audio=on and #hdmi_drive=2.Reboot and run:

sudo su

cd ~/bin

./ax25-stop

also run :

sudo su

cd ~/bin

./ax25=disable

Now select fldigi from the "internet menu" on the home screen and you should be able to go to the "configure" menu of fldigi then sound card and select "port audio" in the drop down menu you should see the selection for "udrc". If you dont it either means you have not shut down ax25 or you didn't comment out dtparam=audio=on or hdmi_drive=2

Also from the home screen of pi go to preferences and bring up "Audio Device Settings" and setup PCM, ADC Level and LO Driver Gain.

I found that setting the audio out (Transmit) levels where easy to adjust to -20db using the alsa mixer controls of PCM and Lo Driver Gain. I use  a free audio spectrum analyzer called "Spectrum Lab ver 2.93" for setting the audio drive level on fldigi for FM vhf and uhf.  For HF the best thing is to adjust the xmit drive level so you have NO ALC showing for ssb transmit. The signals sound clean on second TM V71 I have. Also the receive gain was easy to adjust to keep the  audio within range of the green indicator diamond on fldigi.

I had not experienced the issues that people were having with FT817 at Ft 891 ?? but I had not tried fldigi with the beta 5 version of the image. Beta 6 seems to work just fine with  the Kenwood TM V71.

Joe K3JV


On 12/23/2018 10:00 PM, John D Hays - K7VE wrote:
fldigi allows you to key the radio using the gpio pin interface (12) to mini din-6 (left)

On Sun, Dec 23, 2018 at 6:44 PM Jack Spitznagel <kd4iz@...> wrote:

Hi Joe,

 

You have a radio I do not know anything about. I’m only about a week ahead of you in learning how to make DRAWS sing. I just happened to have been working with fldigi and my IC-7000 and the questions you asked were central to making fldigi work with the DRAWS hat audio device and that rig.

 

How did you configure fldigi to key your radio? Since you are no longer using a SignaLink, you can’t rely on the SL VOX keying circuit.  If you want to use VOX for PTT, the radio has to have a VOX function and it has to be set up and adjusted.

 

Only other approach I can think of is to make sure your radio can be controlled and/or keyed by flrig’s CAT control and set it up. Then set fldigi to control and key the radio using flrig. That seemed to work for me with my IC-7000 and Yaesu FT-817.

 

Sorry I can’t be more helpful.

 

KD4IZ

Jack Spitznagel

FM19oo

 

 

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Joseph Vilardo
Sent: Sunday, December 23, 2018 20:36
To: udrc@nw-digital-radio.groups.io
Subject: Re: [udrc] amixer questions Re: Set Up Issues #setup #fldigi #draws

 

Jack

Next issue is with getting the radio to transmit. First off, I have used Fldigi with the TM-V71 many times on vhf uhf with success using a signalink and a sound cards with simple interfaces. I noticed right of the bat that the squelch on my radio does not stop the waterfall with the DRAWS interface...what is that about? Using the alsa mixer control no value of ADC changes the waterfall appearance, it doesn't dim or get brighter with open squelch. Squelching off the signal of the radio does not stop the water fall ??? I have never seen that before. Lastly I cant key the radio and no value of Lo Drive Gain or PCM makes any difference.

Do you have any suggestions ???

Joe K3JV

On 12/23/2018 5:58 PM, Jack Spitznagel wrote:

Joe,

 

  1. Check to make absolutely sure that Direwolf is not running after your reboot.
  2. If it is not running, you should see PortAudio as a selectable option. Check the box.
  3. Now Select udrc: - (hw:0,0) for both capture and playback.
  4. You can also check “Device supports fell duplex” (it is in mine by default and I just left it that way)

 

Hope that helped.

 

KD4IZ

Jack Spitznagel

FM19oo

 

 

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Joseph Vilardo
Sent: Sunday, December 23, 2018 16:49
To: udrc@nw-digital-radio.groups.io
Subject: Re: [udrc] amixer questions Re: Set Up Issues #setup #fldigi #draws

 

I am looking for some basic guidance on getting fldigi configured for VHF and UHF. I have been successful with the DRAWS Beta 5 image and running Direwolf/YAAC and now that I know the "core image" checks out and works. I rebooted the PI/DRAWS combo and shut down Direwolf and ax25 with this command sequence: cd bin, sudo su, ./ax25-disable.
I then selected fldigi from the drop down menu on the home screen of beta 5 image. When the configuration helper for fldigi comes to selecting the sound card I am left with one option and that is to select "pulseaudio" and it responds wit no pulseaudio server. It doesn't give me an option to choose udrc 0 or 1.
What do I do from here to get an audio source selected ???
Thanks
Joe K3JV


--
J Spitznagel
Science River LLC
KD4IZ


--
J Spitznagel
Science River LLC
KD4IZ


--


John D. Hays
Edmonds, WA
K7VE

   



Re: amixer questions Re: Set Up Issues #setup #fldigi #draws

Julian OH8STN <julian@...>
 

Excellent write up Joe.
Did you adjust any other setting than adjusting ADC level in alsamixer for receive level?

Outstanding post. 
Thanks for sharing 

Julian

Julian OH8STN
www.oh8stn.org
www.youtube.com/c/OH8STN

On 25 Dec 2018 05:13, Joseph Vilardo <jvilardo@...> wrote:

Gents

I wanted to share the good news of having success with the Beta6 image of draws with Direwolf ,  YAAC and a leap today with fldigi running on a Kenwood TM-V71 dual bander.

I downloaded the beta 6 image today and ran through Basil's "Verify_Config.md". I found a  notation symbol that gave me trouble until I changed it.

Under "check ALSA settings for deviation " instructions go as follows:

cd  ~/n7nix/debug

~/alsa-show.sh

I  removing the tilde and the ~/ for the line alsa-show.sh after trying the command as noted several times and then it ran fine.

At first I couldn't get fldigi to allow me to select udrc under the sound card configuration. It just wasn't there. During the Verify_Config.md the instructions required two changes in the /boot/config.txt to test analog audio un comment, remove the # from dtparam=audio=on and /boot/config.txt  hdmi_drive=2 when your done with the Verify_Config.md make sure you go back to /boot/config.txt and comment out, put the # at the beginning of the lines #dtparam=audio=on and #hdmi_drive=2.Reboot and run:

sudo su

cd ~/bin

./ax25-stop

also run :

sudo su

cd ~/bin

./ax25=disable

Now select fldigi from the "internet menu" on the home screen and you should be able to go to the "configure" menu of fldigi then sound card and select "port audio" in the drop down menu you should see the selection for "udrc". If you dont it either means you have not shut down ax25 or you didn't comment out dtparam=audio=on or hdmi_drive=2

Also from the home screen of pi go to preferences and bring up "Audio Device Settings" and setup PCM, ADC Level and LO Driver Gain.

I found that setting the audio out (Transmit) levels where easy to adjust to -20db using the alsa mixer controls of PCM and Lo Driver Gain. I use  a free audio spectrum analyzer called "Spectrum Lab ver 2.93" for setting the audio drive level on fldigi for FM vhf and uhf.  For HF the best thing is to adjust the xmit drive level so you have NO ALC showing for ssb transmit. The signals sound clean on second TM V71 I have. Also the receive gain was easy to adjust to keep the  audio within range of the green indicator diamond on fldigi.

I had not experienced the issues that people were having with FT817 at Ft 891 ?? but I had not tried fldigi with the beta 5 version of the image. Beta 6 seems to work just fine with  the Kenwood TM V71.

Joe K3JV


On 12/23/2018 10:00 PM, John D Hays - K7VE wrote:
fldigi allows you to key the radio using the gpio pin interface (12) to mini din-6 (left)

On Sun, Dec 23, 2018 at 6:44 PM Jack Spitznagel <kd4iz@...> wrote:

Hi Joe,

 

You have a radio I do not know anything about. I’m only about a week ahead of you in learning how to make DRAWS sing. I just happened to have been working with fldigi and my IC-7000 and the questions you asked were central to making fldigi work with the DRAWS hat audio device and that rig.

 

How did you configure fldigi to key your radio? Since you are no longer using a SignaLink, you can’t rely on the SL VOX keying circuit.  If you want to use VOX for PTT, the radio has to have a VOX function and it has to be set up and adjusted.

 

Only other approach I can think of is to make sure your radio can be controlled and/or keyed by flrig’s CAT control and set it up. Then set fldigi to control and key the radio using flrig. That seemed to work for me with my IC-7000 and Yaesu FT-817.

 

Sorry I can’t be more helpful.

 

KD4IZ

Jack Spitznagel

FM19oo

 

 

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Joseph Vilardo
Sent: Sunday, December 23, 2018 20:36
To: udrc@nw-digital-radio.groups.io
Subject: Re: [udrc] amixer questions Re: Set Up Issues #setup #fldigi #draws

 

Jack

Next issue is with getting the radio to transmit. First off, I have used Fldigi with the TM-V71 many times on vhf uhf with success using a signalink and a sound cards with simple interfaces. I noticed right of the bat that the squelch on my radio does not stop the waterfall with the DRAWS interface...what is that about? Using the alsa mixer control no value of ADC changes the waterfall appearance, it doesn't dim or get brighter with open squelch. Squelching off the signal of the radio does not stop the water fall ??? I have never seen that before. Lastly I cant key the radio and no value of Lo Drive Gain or PCM makes any difference.

Do you have any suggestions ???

Joe K3JV

On 12/23/2018 5:58 PM, Jack Spitznagel wrote:

Joe,

 

  1. Check to make absolutely sure that Direwolf is not running after your reboot.
  2. If it is not running, you should see PortAudio as a selectable option. Check the box.
  3. Now Select udrc: - (hw:0,0) for both capture and playback.
  4. You can also check “Device supports fell duplex” (it is in mine by default and I just left it that way)

 

Hope that helped.

 

KD4IZ

Jack Spitznagel

FM19oo

 

 

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Joseph Vilardo
Sent: Sunday, December 23, 2018 16:49
To: udrc@nw-digital-radio.groups.io
Subject: Re: [udrc] amixer questions Re: Set Up Issues #setup #fldigi #draws

 

I am looking for some basic guidance on getting fldigi configured for VHF and UHF. I have been successful with the DRAWS Beta 5 image and running Direwolf/YAAC and now that I know the "core image" checks out and works. I rebooted the PI/DRAWS combo and shut down Direwolf and ax25 with this command sequence: cd bin, sudo su, ./ax25-disable.
I then selected fldigi from the drop down menu on the home screen of beta 5 image. When the configuration helper for fldigi comes to selecting the sound card I am left with one option and that is to select "pulseaudio" and it responds wit no pulseaudio server. It doesn't give me an option to choose udrc 0 or 1.
What do I do from here to get an audio source selected ???
Thanks
Joe K3JV


--
J Spitznagel
Science River LLC
KD4IZ


--
J Spitznagel
Science River LLC
KD4IZ


--


John D. Hays
Edmonds, WA
K7VE

   



Re: Cant turn off direwolf and ax25 #configuration #management #draws #direwolf #ax25

Art Olson
 

Bob

Can’t speak for this implementation as I am waiting for the next DRAW run to be shipped. However my experience with other rpi implementations, my SD card contained a single image. I make sure by reformatting with SD formatter then burn image with etcher. You could try this approach. 

FWIW

Art


On Dec 24, 2018, at 8:58 PM, Bob Orrett <boborrett@...> wrote:

Merry Christmas,  Basil.
I dont expect to hear back from you for a few days.
I am trying to get wsjtx and js8call running. I did have this working so I know the 817 radio is ok. I could not use the supplied cables but I have an alternate cable that worked. However, now, with a new image burned, I cannot get the audio part to work. I do see the correct codec in settings for wsjtx and js8call but not audio appears. I
As you suggested, I tried stating direwolf with ./ax25-start but I get this message
A dependance job for ax25-mheardd.. service failed. See 'journalctl -xe' for details.
I did run journalctl -xe and got a full page report. I can screen capture it but I have no idea how to send it to you.
In red it says "Failed to start AX25 device"

So there must be something wrong with my new image but I have tried several times. 
I did notice that the one time it did work, on first bootup ,I was asked a few questions before it went to the standard desktop. I have never been asked since for anything, no passwords, no timezone, etc, for any new image I have tried, either bata5 or beta5. It just goes directly to the standard desktop upon bootup. Even first time. To burn the image i download zipped file from your download page. Then unzip with windows 10 then burn to the sd card with Etcher. I usually just burn onto the same sd card that had the previous burn. Am I doing this correctly? Does it matter that the sd card was not empty when I burn onto it?
I will try another burn with a new download. 

Btw my return on journalctl -xe also said 
Error setting device : ax0 parks

Same for ax1

Hope that's enough info
Bob ve3obo

On Mon, Dec 24, 2018, 01:21 Basil Gunn <basil@... wrote:

if direwolf & ax-25 are already stopped then running ./ax25-stop does
not respond with anything.

type pidof direwolf
if no process id is printed direwolf is not running

try starting & stopping it.
./ax25-start
./ax25-stop

Is your radio set for AFOUT or DISCOUT?
 - On your radio what is Menu #39 (PKT MIC) set to?
 - On your radio what is Menu #40 (PKT RATE) set to?
Are you using VHF/UHF or HF?
Which audio port are you using left or right?

Send me the console output of
cd
cd bin
./showudrc.sh
./alsa-show.sh

draws-beta5 image defaulted to using DISCOUT (IN1)
draws-beta6 image defaults to using AFOUT (IN2)

/Basil

Bob Orrett <boborrett@...> writes:

> I am a newbie to RPi and linux.
> I have the beta6 installed and running. I cannot seem to be able to stop
> direwolf and ax25 so that ft8 and js8call will get access to the draws
> sound card.
> I entered
>
> cd
> cd bin
> sudo su
> ./ax25-stop
>
> The pi returns the command prompt but not anything like "ax25 has stopped".
> I see the correct sound card input and output codec in the settings for
> these programs (ft8 and js8call) but no audio from the ft817 radio. I had
> this working before. What am I missing?
>
> Bob ve3obo




Re: Cant turn off direwolf and ax25 #configuration #management #draws #direwolf #ax25

Jack Spitznagel
 

Bob,

That is a mistake I often make when I forget and reflexively try to use DOS/Windows conventions in LINUX. It is confusing.

You want to be in “~/bin”, not “/bin”. note the “~”!

In the DOS/Windows world that would be the same as saying “cd \home\pi\bin”.

This is the bin folder in your user account “home” directory. You will find show

Hope that help


On Dec 24, 2018, at 21:09, Bob Orrett <boborrett@...> wrote:

Forgot
You asked for output from ./showudrc.sh

I get bash: ./showudrc.sh:  no such file or directory. 
I was in /bin
Bob ve3obo

On Mon, Dec 24, 2018, 01:21 Basil Gunn <basil@... wrote:

if direwolf & ax-25 are already stopped then running ./ax25-stop does
not respond with anything.

type pidof direwolf
if no process id is printed direwolf is not running

try starting & stopping it.
./ax25-start
./ax25-stop

Is your radio set for AFOUT or DISCOUT?
 - On your radio what is Menu #39 (PKT MIC) set to?
 - On your radio what is Menu #40 (PKT RATE) set to?
Are you using VHF/UHF or HF?
Which audio port are you using left or right?

Send me the console output of
cd
cd bin
./showudrc.sh
./alsa-show.sh

draws-beta5 image defaulted to using DISCOUT (IN1)
draws-beta6 image defaults to using AFOUT (IN2)

/Basil

Bob Orrett <boborrett@...> writes:

> I am a newbie to RPi and linux.
> I have the beta6 installed and running. I cannot seem to be able to stop
> direwolf and ax25 so that ft8 and js8call will get access to the draws
> sound card.
> I entered
>
> cd
> cd bin
> sudo su
> ./ax25-stop
>
> The pi returns the command prompt but not anything like "ax25 has stopped".
> I see the correct sound card input and output codec in the settings for
> these programs (ft8 and js8call) but no audio from the ft817 radio. I had
> this working before. What am I missing?
>
> Bob ve3obo




--
J Spitznagel
Science River LLC
KD4IZ


Re: amixer questions Re: Set Up Issues #setup #fldigi #draws

Joseph Vilardo
 

Gents

I wanted to share the good news of having success with the Beta6 image of draws with Direwolf ,  YAAC and a leap today with fldigi running on a Kenwood TM-V71 dual bander.

I downloaded the beta 6 image today and ran through Basil's "Verify_Config.md". I found a  notation symbol that gave me trouble until I changed it.

Under "check ALSA settings for deviation " instructions go as follows:

cd  ~/n7nix/debug

~/alsa-show.sh

I  removing the tilde and the ~/ for the line alsa-show.sh after trying the command as noted several times and then it ran fine.

At first I couldn't get fldigi to allow me to select udrc under the sound card configuration. It just wasn't there. During the Verify_Config.md the instructions required two changes in the /boot/config.txt to test analog audio un comment, remove the # from dtparam=audio=on and /boot/config.txt  hdmi_drive=2 when your done with the Verify_Config.md make sure you go back to /boot/config.txt and comment out, put the # at the beginning of the lines #dtparam=audio=on and #hdmi_drive=2.Reboot and run:

sudo su

cd ~/bin

./ax25-stop

also run :

sudo su

cd ~/bin

./ax25=disable

Now select fldigi from the "internet menu" on the home screen and you should be able to go to the "configure" menu of fldigi then sound card and select "port audio" in the drop down menu you should see the selection for "udrc". If you dont it either means you have not shut down ax25 or you didn't comment out dtparam=audio=on or hdmi_drive=2

Also from the home screen of pi go to preferences and bring up "Audio Device Settings" and setup PCM, ADC Level and LO Driver Gain.

I found that setting the audio out (Transmit) levels where easy to adjust to -20db using the alsa mixer controls of PCM and Lo Driver Gain. I use  a free audio spectrum analyzer called "Spectrum Lab ver 2.93" for setting the audio drive level on fldigi for FM vhf and uhf.  For HF the best thing is to adjust the xmit drive level so you have NO ALC showing for ssb transmit. The signals sound clean on second TM V71 I have. Also the receive gain was easy to adjust to keep the  audio within range of the green indicator diamond on fldigi.

I had not experienced the issues that people were having with FT817 at Ft 891 ?? but I had not tried fldigi with the beta 5 version of the image. Beta 6 seems to work just fine with  the Kenwood TM V71.

Joe K3JV


On 12/23/2018 10:00 PM, John D Hays - K7VE wrote:
fldigi allows you to key the radio using the gpio pin interface (12) to mini din-6 (left)

On Sun, Dec 23, 2018 at 6:44 PM Jack Spitznagel <kd4iz@...> wrote:

Hi Joe,

 

You have a radio I do not know anything about. I’m only about a week ahead of you in learning how to make DRAWS sing. I just happened to have been working with fldigi and my IC-7000 and the questions you asked were central to making fldigi work with the DRAWS hat audio device and that rig.

 

How did you configure fldigi to key your radio? Since you are no longer using a SignaLink, you can’t rely on the SL VOX keying circuit.  If you want to use VOX for PTT, the radio has to have a VOX function and it has to be set up and adjusted.

 

Only other approach I can think of is to make sure your radio can be controlled and/or keyed by flrig’s CAT control and set it up. Then set fldigi to control and key the radio using flrig. That seemed to work for me with my IC-7000 and Yaesu FT-817.

 

Sorry I can’t be more helpful.

 

KD4IZ

Jack Spitznagel

FM19oo

 

 

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Joseph Vilardo
Sent: Sunday, December 23, 2018 20:36
To: udrc@nw-digital-radio.groups.io
Subject: Re: [udrc] amixer questions Re: Set Up Issues #setup #fldigi #draws

 

Jack

Next issue is with getting the radio to transmit. First off, I have used Fldigi with the TM-V71 many times on vhf uhf with success using a signalink and a sound cards with simple interfaces. I noticed right of the bat that the squelch on my radio does not stop the waterfall with the DRAWS interface...what is that about? Using the alsa mixer control no value of ADC changes the waterfall appearance, it doesn't dim or get brighter with open squelch. Squelching off the signal of the radio does not stop the water fall ??? I have never seen that before. Lastly I cant key the radio and no value of Lo Drive Gain or PCM makes any difference.

Do you have any suggestions ???

Joe K3JV

On 12/23/2018 5:58 PM, Jack Spitznagel wrote:

Joe,

 

  1. Check to make absolutely sure that Direwolf is not running after your reboot.
  2. If it is not running, you should see PortAudio as a selectable option. Check the box.
  3. Now Select udrc: - (hw:0,0) for both capture and playback.
  4. You can also check “Device supports fell duplex” (it is in mine by default and I just left it that way)

 

Hope that helped.

 

KD4IZ

Jack Spitznagel

FM19oo

 

 

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Joseph Vilardo
Sent: Sunday, December 23, 2018 16:49
To: udrc@nw-digital-radio.groups.io
Subject: Re: [udrc] amixer questions Re: Set Up Issues #setup #fldigi #draws

 

I am looking for some basic guidance on getting fldigi configured for VHF and UHF. I have been successful with the DRAWS Beta 5 image and running Direwolf/YAAC and now that I know the "core image" checks out and works. I rebooted the PI/DRAWS combo and shut down Direwolf and ax25 with this command sequence: cd bin, sudo su, ./ax25-disable.
I then selected fldigi from the drop down menu on the home screen of beta 5 image. When the configuration helper for fldigi comes to selecting the sound card I am left with one option and that is to select "pulseaudio" and it responds wit no pulseaudio server. It doesn't give me an option to choose udrc 0 or 1.
What do I do from here to get an audio source selected ???
Thanks
Joe K3JV


--
J Spitznagel
Science River LLC
KD4IZ


--
J Spitznagel
Science River LLC
KD4IZ


--


John D. Hays
Edmonds, WA
K7VE

   


Re: FT891, FT817, Audio Levels, I/O Fail , and Documentation #draws #ft817 #hfmodes

Julian OH8STN <julian@...>
 

Tired, I meant "ALC"

Julian OH8STN
www.oh8stn.org
www.youtube.com/c/OH8STN

On 25 Dec 2018 04:52, Julian OH8STN <julian@...> wrote:
Hi John
Adjusting audio output level to 0 (zero) worked and I'm being heard on pskreporter now. Art send his 891 settings, which I hope will help with the receive levels. I'll give those a go after some sleep and family time. AGC is also at a reasonable level now. 

It's working well enough that  I got some good video captures with FLDigi, WSJTX and JS8Call. It's not perfect yet, but it's close enough that I know we'll get there.

John, Basil, Jack, Art, everyone enjoy the holiday.

73
Julian

Julian OH8STN
www.oh8stn.org
www.youtube.com/c/OH8STN

On 25 Dec 2018 01:51, Julian OH8STN <julian@...> wrote:
Naturally yes, but not the full range of the sitting. I'll continue the testing with that and report back.
Enjoy the holiday guys.

Julian


Julian OH8STN
www.oh8stn.org
www.youtube.com/c/OH8STN


On 24 Dec 2018 23:44, John D Hays - K7VE <john@...> wrote:
Have you looked at the digital mic gain? (FT-817 Menu 25)




Re: FT891, FT817, Audio Levels, I/O Fail , and Documentation #draws #ft817 #hfmodes

Julian OH8STN <julian@...>
 

Hi John
Adjusting audio output level to 0 (zero) worked and I'm being heard on pskreporter now. Art send his 891 settings, which I hope will help with the receive levels. I'll give those a go after some sleep and family time. AGC is also at a reasonable level now. 

It's working well enough that  I got some good video captures with FLDigi, WSJTX and JS8Call. It's not perfect yet, but it's close enough that I know we'll get there.

John, Basil, Jack, Art, everyone enjoy the holiday.

73
Julian

Julian OH8STN
www.oh8stn.org
www.youtube.com/c/OH8STN

On 25 Dec 2018 01:51, Julian OH8STN <julian@...> wrote:
Naturally yes, but not the full range of the sitting. I'll continue the testing with that and report back.
Enjoy the holiday guys.

Julian


Julian OH8STN
www.oh8stn.org
www.youtube.com/c/OH8STN


On 24 Dec 2018 23:44, John D Hays - K7VE <john@...> wrote:
Have you looked at the digital mic gain? (FT-817 Menu 25)



Re: FT891, FT817, Audio Levels, I/O Fail , and Documentation #draws #ft817 #hfmodes

Julian OH8STN <julian@...>
 

Thank you Art

Julian OH8STN
www.oh8stn.org
www.youtube.com/c/OH8STN

On 24 Dec 2018 17:53, "art upton via Groups.Io" <artupton@...> wrote:
FYI, I was able to get my FT-891 to work before a beta image was available following the script to set the mixers to HF audio out instead of DISC out.
On Beta 5, I had to run the disable ax script provided and I used the original script posted and it works. I made Fldigi contacts.

the FT-450D gets driven way too hard by any sound card interface and I could not get it to work as it was always over driven at the lowest settings.  I need like a 100k ohm resistor in the line I think.

Art

script that was posted to set to HF audio 
#!/bin/bash
 
amixer -c udrc -s << EOF
#  Set input and output levels to 0dB
sset 'ADC Level' -2.0dB
sset 'LO Driver Gain' 0dB
sset 'PCM' 0.0dB
 
#  Turn on AFOUT
sset 'CM_L to Left Mixer Negative Resistor' '10 kOhm'
# original sset 'IN1_L to Left Mixer Positive Resistor' '10 kOhm'
sset 'IN1_L to Left Mixer Positive Resistor' 'Off'
 
#  Turn on DISCOUT
sset 'CM_R to Right Mixer Negative Resistor' '10 kOhm'
sset 'IN1_R to Right Mixer Positive Resistor' '10 kOhm'
 
#  Turn off unnecessary pins
sset 'IN1_L to Right Mixer Negative Resistor' 'Off'
sset 'IN1_R to Left Mixer Positive Resistor' 'Off'
# original sset 'IN2_L to Left Mixer Positive Resistor' 'Off'
# original sset 'IN2_L to Right Mixer Positive Resistor' 'Off'
sset 'IN2_L to Left Mixer Positive Resistor' '10 kOhm'
sset 'IN2_L to Right Mixer Positive Resistor' '10 kOhm'
 
sset 'IN2_R to Left Mixer Negative Resistor' 'Off'
sset 'IN2_R to Right Mixer Positive Resistor' 'Off'
sset 'IN3_L to Left Mixer Positive Resistor' 'Off'
sset 'IN3_L to Right Mixer Negative Resistor' 'Off'
sset 'IN3_R to Left Mixer Negative Resistor' 'Off'
sset 'IN3_R to Right Mixer Positive Resistor' 'Off'
 
sset 'Mic PGA' off
sset 'PGA Level' 0
 
# Disable and clear AGC
sset 'ADCFGA Right Mute' off
sset 'ADCFGA Left Mute' off
sset 'AGC Attack Time' 0
sset 'AGC Decay Time' 0
sset 'AGC Gain Hysteresis' 0
sset 'AGC Hysteresis' 0
sset 'AGC Max PGA' 0
sset 'AGC Noise Debounce' 0
sset 'AGC Noise Threshold' 0
sset 'AGC Signal Debounce' 0
sset 'AGC Target Level' 0
sset 'AGC Left' off
sset 'AGC Right' off
 
# Turn off High Power output
sset 'HP DAC' off
sset 'HP Driver Gain' 0
sset 'HPL Output Mixer L_DAC' off
sset 'HPR Output Mixer R_DAC' off
sset 'HPL Output Mixer IN1_L' off
sset 'HPR Output Mixer IN1_R' off
 
#  Turn on the LO DAC
sset 'LO DAC' on
 
#  Turn on AFIN
sset 'LOL Output Mixer L_DAC' on
 
#  Turn on TONEIN
sset 'LOR Output Mixer R_DAC' on
EOF
alsactl store


Re: Cant turn off direwolf and ax25 #configuration #management #draws #direwolf #ax25

Bob Orrett <boborrett@...>
 

Forgot
You asked for output from ./showudrc.sh

I get bash: ./showudrc.sh:  no such file or directory. 
I was in /bin
Bob ve3obo

On Mon, Dec 24, 2018, 01:21 Basil Gunn <basil@... wrote:

if direwolf & ax-25 are already stopped then running ./ax25-stop does
not respond with anything.

type pidof direwolf
if no process id is printed direwolf is not running

try starting & stopping it.
./ax25-start
./ax25-stop

Is your radio set for AFOUT or DISCOUT?
 - On your radio what is Menu #39 (PKT MIC) set to?
 - On your radio what is Menu #40 (PKT RATE) set to?
Are you using VHF/UHF or HF?
Which audio port are you using left or right?

Send me the console output of
cd
cd bin
./showudrc.sh
./alsa-show.sh

draws-beta5 image defaulted to using DISCOUT (IN1)
draws-beta6 image defaults to using AFOUT (IN2)

/Basil

Bob Orrett <boborrett@...> writes:

> I am a newbie to RPi and linux.
> I have the beta6 installed and running. I cannot seem to be able to stop
> direwolf and ax25 so that ft8 and js8call will get access to the draws
> sound card.
> I entered
>
> cd
> cd bin
> sudo su
> ./ax25-stop
>
> The pi returns the command prompt but not anything like "ax25 has stopped".
> I see the correct sound card input and output codec in the settings for
> these programs (ft8 and js8call) but no audio from the ft817 radio. I had
> this working before. What am I missing?
>
> Bob ve3obo




Re: Cant turn off direwolf and ax25 #configuration #management #draws #direwolf #ax25

Bob Orrett <boborrett@...>
 

Merry Christmas,  Basil.
I dont expect to hear back from you for a few days.
I am trying to get wsjtx and js8call running. I did have this working so I know the 817 radio is ok. I could not use the supplied cables but I have an alternate cable that worked. However, now, with a new image burned, I cannot get the audio part to work. I do see the correct codec in settings for wsjtx and js8call but not audio appears. I
As you suggested, I tried stating direwolf with ./ax25-start but I get this message
A dependance job for ax25-mheardd.. service failed. See 'journalctl -xe' for details.
I did run journalctl -xe and got a full page report. I can screen capture it but I have no idea how to send it to you.
In red it says "Failed to start AX25 device"

So there must be something wrong with my new image but I have tried several times. 
I did notice that the one time it did work, on first bootup ,I was asked a few questions before it went to the standard desktop. I have never been asked since for anything, no passwords, no timezone, etc, for any new image I have tried, either bata5 or beta5. It just goes directly to the standard desktop upon bootup. Even first time. To burn the image i download zipped file from your download page. Then unzip with windows 10 then burn to the sd card with Etcher. I usually just burn onto the same sd card that had the previous burn. Am I doing this correctly? Does it matter that the sd card was not empty when I burn onto it?
I will try another burn with a new download. 

Btw my return on journalctl -xe also said 
Error setting device : ax0 parks

Same for ax1

Hope that's enough info
Bob ve3obo

On Mon, Dec 24, 2018, 01:21 Basil Gunn <basil@... wrote:

if direwolf & ax-25 are already stopped then running ./ax25-stop does
not respond with anything.

type pidof direwolf
if no process id is printed direwolf is not running

try starting & stopping it.
./ax25-start
./ax25-stop

Is your radio set for AFOUT or DISCOUT?
 - On your radio what is Menu #39 (PKT MIC) set to?
 - On your radio what is Menu #40 (PKT RATE) set to?
Are you using VHF/UHF or HF?
Which audio port are you using left or right?

Send me the console output of
cd
cd bin
./showudrc.sh
./alsa-show.sh

draws-beta5 image defaulted to using DISCOUT (IN1)
draws-beta6 image defaults to using AFOUT (IN2)

/Basil

Bob Orrett <boborrett@...> writes:

> I am a newbie to RPi and linux.
> I have the beta6 installed and running. I cannot seem to be able to stop
> direwolf and ax25 so that ft8 and js8call will get access to the draws
> sound card.
> I entered
>
> cd
> cd bin
> sudo su
> ./ax25-stop
>
> The pi returns the command prompt but not anything like "ax25 has stopped".
> I see the correct sound card input and output codec in the settings for
> these programs (ft8 and js8call) but no audio from the ft817 radio. I had
> this working before. What am I missing?
>
> Bob ve3obo



3321 - 3340 of 5716