Check This File carefully, the last line performs the 2X

On Jul 21, 2020, at 11:53 AM, Jack Spitznagel <kd4iz@...> wrote:

Bryan and John,

Essentially the same as yours Bryan! The one line different says:

in5:         +2.50 V

Same as on the Dashboard.

 

The very first thing I did when I re-checked it just now was to update the DRAWS manager “just in case”. I also came back and rebooted the Pi just in case and it still reads in5: +2.50 V. I also had run the manager update yesterday, but had not rebooted – same result. 

 

I wonder if being behind one image version might be an issue? I have lost track, but think this is v16.

 

Also, are you both running Pi3’s or also Pi4’s?

 

Jack – KD4IZ

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Bryan Hoyer
Sent: Tuesday, July 21, 2020 14:00
To: udrc@nw-digital-radio.groups.io
Subject: Re: [draws and udrc] Update for ADC Config File #sensors #ADC

 

What does sensors report?

 

pi@K7UDR:~ $ sensors

rpi_volt-isa-0000

Adapter: ISA adapter

in0:              N/A  

 

ads1015-i2c-1-48

Adapter: bcm2835 I2C adapter

+12V:        +13.52 V  

+5V:          +5.06 V  

User ADC 1:   +0.00 V  

User ADC 2:   +0.00 V  

On Jul 21, 2020, at 10:34 AM, Jack Spitznagel <kd4iz@...> wrote:

 

Bryan,

 

That’s very interesting! Here is what the new board I just received is reporting:

<image003.jpg>

 

I see “in5: +2.50V” not “+5V: +5.06V” on that top line. Maybe I need to run an update of code here?

Jack – KD4IZ

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Bryan Hoyer
Sent: Tuesday, July 21, 2020 13:11
To: udrc@nw-digital-radio.groups.io
Subject: Re: [draws and udrc] Update for ADC Config File #sensors #ADC

 

Jack,

 

I just ran DRAWS Manager with the updated config and it works fine.

 

<image004.png>

On Jul 17, 2020, at 12:45 PM, Jack Spitznagel <kd4iz@...> wrote:

 

Great! 

I missed that he was building. Best success to him!

-Jack

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Bryan Hoyer
Sent: Friday, July 17, 2020 15:06
To: udrc@nw-digital-radio.groups.io
Subject: Re: [draws and udrc] Update for ADC Config File #sensors #ADC

 

John will add it to a future release, after he finishes his new home in Kingston WA

On Jul 17, 2020, at 12:01 PM, Jack Spitznagel <kd4iz@...> wrote:

 

Bryan,

 

Quick Question on that: Has John implemented this in the DRAWS Manager? Does not appear to be the case. At the bottom of current version, the status bar says:

 

Digital Radio Amateur Work Station | Adapter: bcm2835 I2C adapter • +12V: +13.68 V • in5: +2.50 V • User ADC 1: +0.01 V • User ADC 2: +0.00 V 

Raspberry Pi 4 Model B Rev 1.2 | CPU Temp: 108.24° F (42.36° C) • Uptime: 21 hrs 49 mins • Load AVG: 1m:1.07 5m:1.19 15m:1.17 

 

Not in a hurry to do this, but the replacement board is working well… Many thanks.

 

Jack Spitznagel – KD4IZ

Trustee for NR3DT

The USCGC W-37 Amateur Radio Group

 

 

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Bryan Hoyer
Sent: Friday, July 17, 2020 14:51
To: udrc@nw-digital-radio.groups.io
Subject: [draws and udrc] Update for ADC Config File #sensors #ADC

 

Hello All,

DRAWS Has an on-board ADC to monitor the 12V supply. Sometime after the first run, 5V monitoring was added, but the config file wasn't updated so the sensors command doesn't work correctly.

the fix is to change /etc/sensors.d/draws as follows:

pi@K7UDR:/etc/sensors.d $ cat draws 

#DRAWS uses the TL024 Which is SW Compatible with thw ADS1015

#It's an 8 Channel ADC, but only 4 Channels are pinned out

 

chip "ads1015-*"

        label in4 "+12V"

 label in5 "+5V"

label in6 "User ADC 1"

label in7 "User ADC 2"

compute in4 ((48.7/10)+1)*@, @/((48.7/10)+1)

        compute in5 ((10/10)+1)*@, @/((10/10)+1)

 

pi@K7UDR:/etc/sensors.d $ sensors

rpi_volt-isa-0000

Adapter: ISA adapter

in0:              N/A  

 

ads1015-i2c-1-48

Adapter: bcm2835 I2C adapter

+12V:        +13.52 V  

+5V:          +5.06 V  

User ADC 1:   +0.00 V  

User ADC 2:   +0.00 V  

To learn more about this, check out the man page for lm-sensors

Cheers,
Bryan K7UDR

 

 

 

On Jul 21, 2020, at 11:44 AM, Chuck - VA7UL <va7ul@...> wrote:

Hi Bryan,

How do I cancel an order for a case?  I tried submitting a request via the proper contact web page but have not received a response in well over a month.  I no longer have a need for the case, and I am not able to cross the closed border to pick up from my US address anyway.

I checked my PayPal account and have not seen any refund.  This refers to Order #6413, April 20, 2019.   Is there a better way to cancel the order rather than using the contact given for this process?

Many thanks,
Chuck  -  VA7UL / VA7ULD / VE1CAM

What does sensors report?

On Jul 21, 2020, at 10:34 AM, Jack Spitznagel <kd4iz@...> wrote:

Bryan,

 

That’s very interesting! Here is what the new board I just received is reporting:

<image003.jpg>

 

I see “in5: +2.50V” not “+5V: +5.06V” on that top line. Maybe I need to run an update of code here?

Jack – KD4IZ

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Bryan Hoyer
Sent: Tuesday, July 21, 2020 13:11
To: udrc@nw-digital-radio.groups.io
Subject: Re: [draws and udrc] Update for ADC Config File #sensors #ADC

 

Jack,

 

I just ran DRAWS Manager with the updated config and it works fine.

 

<image004.png>

On Jul 17, 2020, at 12:45 PM, Jack Spitznagel <kd4iz@...> wrote:

 

Great! 

I missed that he was building. Best success to him!

-Jack

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Bryan Hoyer
Sent: Friday, July 17, 2020 15:06
To: udrc@nw-digital-radio.groups.io
Subject: Re: [draws and udrc] Update for ADC Config File #sensors #ADC

 

John will add it to a future release, after he finishes his new home in Kingston WA

On Jul 17, 2020, at 12:01 PM, Jack Spitznagel <kd4iz@...> wrote:

 

Bryan,

 

Quick Question on that: Has John implemented this in the DRAWS Manager? Does not appear to be the case. At the bottom of current version, the status bar says:

 

Digital Radio Amateur Work Station | Adapter: bcm2835 I2C adapter • +12V: +13.68 V • in5: +2.50 V • User ADC 1: +0.01 V • User ADC 2: +0.00 V 

Raspberry Pi 4 Model B Rev 1.2 | CPU Temp: 108.24° F (42.36° C) • Uptime: 21 hrs 49 mins • Load AVG: 1m:1.07 5m:1.19 15m:1.17 

 

Not in a hurry to do this, but the replacement board is working well… Many thanks.

 

Jack Spitznagel – KD4IZ

Trustee for NR3DT

The USCGC W-37 Amateur Radio Group

 

 

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Bryan Hoyer
Sent: Friday, July 17, 2020 14:51
To: udrc@nw-digital-radio.groups.io
Subject: [draws and udrc] Update for ADC Config File #sensors #ADC

 

Hello All,

DRAWS Has an on-board ADC to monitor the 12V supply. Sometime after the first run, 5V monitoring was added, but the config file wasn't updated so the sensors command doesn't work correctly.

the fix is to change /etc/sensors.d/draws as follows:

pi@K7UDR:/etc/sensors.d $ cat draws 

#DRAWS uses the TL024 Which is SW Compatible with thw ADS1015

#It's an 8 Channel ADC, but only 4 Channels are pinned out

 

chip "ads1015-*"

        label in4 "+12V"

 label in5 "+5V"

label in6 "User ADC 1"

label in7 "User ADC 2"

compute in4 ((48.7/10)+1)*@, @/((48.7/10)+1)

        compute in5 ((10/10)+1)*@, @/((10/10)+1)

 

pi@K7UDR:/etc/sensors.d $ sensors

rpi_volt-isa-0000

Adapter: ISA adapter

in0:              N/A  

 

ads1015-i2c-1-48

Adapter: bcm2835 I2C adapter

+12V:        +13.52 V  

+5V:          +5.06 V  

User ADC 1:   +0.00 V  

User ADC 2:   +0.00 V  

To learn more about this, check out the man page for lm-sensors

Cheers,
Bryan K7UDR

 

 

Jack,

On Jul 17, 2020, at 12:45 PM, Jack Spitznagel <kd4iz@...> wrote:

Great! 

I missed that he was building. Best success to him!

-Jack

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Bryan Hoyer
Sent: Friday, July 17, 2020 15:06
To: udrc@nw-digital-radio.groups.io
Subject: Re: [draws and udrc] Update for ADC Config File #sensors #ADC

 

John will add it to a future release, after he finishes his new home in Kingston WA

On Jul 17, 2020, at 12:01 PM, Jack Spitznagel <kd4iz@...> wrote:

 

Bryan,

 

Quick Question on that: Has John implemented this in the DRAWS Manager? Does not appear to be the case. At the bottom of current version, the status bar says:

 

Digital Radio Amateur Work Station | Adapter: bcm2835 I2C adapter • +12V: +13.68 V • in5: +2.50 V • User ADC 1: +0.01 V • User ADC 2: +0.00 V 

Raspberry Pi 4 Model B Rev 1.2 | CPU Temp: 108.24° F (42.36° C) • Uptime: 21 hrs 49 mins • Load AVG: 1m:1.07 5m:1.19 15m:1.17 

 

Not in a hurry to do this, but the replacement board is working well… Many thanks.

 

Jack Spitznagel – KD4IZ

Trustee for NR3DT

The USCGC W-37 Amateur Radio Group

 

 

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Bryan Hoyer
Sent: Friday, July 17, 2020 14:51
To: udrc@nw-digital-radio.groups.io
Subject: [draws and udrc] Update for ADC Config File #sensors #ADC

 

Hello All,

DRAWS Has an on-board ADC to monitor the 12V supply. Sometime after the first run, 5V monitoring was added, but the config file wasn't updated so the sensors command doesn't work correctly.

the fix is to change /etc/sensors.d/draws as follows:

pi@K7UDR:/etc/sensors.d $ cat draws 

#DRAWS uses the TL024 Which is SW Compatible with thw ADS1015

#It's an 8 Channel ADC, but only 4 Channels are pinned out

 

chip "ads1015-*"

        label in4 "+12V"

 label in5 "+5V"

label in6 "User ADC 1"

label in7 "User ADC 2"

compute in4 ((48.7/10)+1)*@, @/((48.7/10)+1)

        compute in5 ((10/10)+1)*@, @/((10/10)+1)

 

pi@K7UDR:/etc/sensors.d $ sensors

rpi_volt-isa-0000

Adapter: ISA adapter

in0:              N/A  

 

ads1015-i2c-1-48

Adapter: bcm2835 I2C adapter

+12V:        +13.52 V  

+5V:          +5.06 V  

User ADC 1:   +0.00 V  

User ADC 2:   +0.00 V  

To learn more about this, check out the man page for lm-sensors

Cheers,
Bryan K7UDR

 

This error message:

connect(): Address already in use

might indicate you have 2 instances of wl2kax25, wl2ktelnet or wl2kd running.
It could happen if you had some hang or other problem that leaves the
connection to the ax25 socket still connected.

Since I have never seen this problem I suggest you reboot and try it
again.

I suspect you would see this error when trying to connect to an RMS
Gateway as well.

Ed Bloom, KD9FRQ via groups.io <ewbloom=verizon.net@groups.io> writes:

On 7/21/2020 10:54 AM, Basil Gunn wrote:

wl2kax25 -c WA9APQ

Following up............just did a quick retry........No Joy

wl2kax25 -c WA9APQ
connect(): Address already in use

Early adopter cards don’t have the 5V monitor capability

On 7/21/2020 10:54 AM, Basil Gunn wrote:

wl2kax25 -c WA9APQ

Following up............just did a quick retry........No Joy

wl2kax25 -c WA9APQ
connect(): Address already in use

The correct syntax to send P2P is:

wl2kax25 -c WA9APQ

without the question marks!

This syntax sends to the RMS Gateway which it looks like you can't
connect with:

wl2kax25 -c WA9APQ-10

Hearing a station with mheard does not guarantee that you will be able
to connect to it with a Winlink client.

I am struggling to send email peer to peer where the end station is
using PC based WinLink and only has the call sign AB9DEF without the -10.

wl2kax25 -c WA9APQ?? This returns : connect(): Address already in use
wl2kax25 -c WA9APQ-10 This times out

I see the station when I run mheard

What am I missing?

Ed, KD9FRQ

I am struggling to send email peer to peer where the end station is
using PC based WinLink and only has the call sign AB9DEF without the -10.

wl2kax25 -c WA9APQ?? This returns : connect(): Address already in use
wl2kax25 -c WA9APQ-10 This times out

I see the station when I run mheard

What am I missing?

Ed, KD9FRQ

Peer to Peer receive is not activating when an inbound request it received.
I see it in a terminal window using the listen command.
What do I need to change to receive inbound Peer to Peer?
Ed Bloom, KD9FRQ

Peer to Peer receive is not activating when an inbound request it received.
I see it in a terminal window using the listen command.
What do I need to change to receive inbound Peer to Peer?
Ed Bloom, KD9FRQ

On Jul 20, 2020, at 6:16 PM, Daniel VE3NI <dgoodier@...> wrote:

Hi Bryan,

 

I updated /etc/sensors.d/draws as indicated and I am now seeing that the +5V sensor is reading +1.17V.

 

I have the early adopter card.

 

Any idea why the voltage might be reading low?

 

Thanks,

Daniel VE3NI

 

 

pi@draws:~ $ cat /etc/sensors.d/draws

#DRAWS uses the TL024 Which is SW Compatible with the ADS1015

#It's an 8 Channel ADC, but only 4 Channels are pinned out

 

chip "ads1015-*"

        label in4 "+12V"

        label in5 "+5V"

        label in6 "User ADC 1"

        label in7 "User ADC 2"

        compute in4 ((48.7/10)+1)*@, @/((48.7/10)+1)

        compute in5 ((10/10)+1)*@, @/((10/10)+1)

 

pi@draws:~ $ sensors

rpi_volt-isa-0000

Adapter: ISA adapter

in0:              N/A

 

ads1015-i2c-1-48

Adapter: bcm2835 I2C adapter

+12V:        +12.33 V

+5V:          +1.17 V

User ADC 1:   +0.00 V

User ADC 2:   +0.00 V

 

pi@draws:~ $