Hi Paul, Thanks for you response. I copied set-udrc-din6.sh to my-udrc-din6.sh, removed everything except the variables that you quoted, and I changed the levels to what you specified. Then I ran

In this case, each port is a separate sound card, so they are each their own Channel 0, as this is a working config. I was using the original direwolf.conf from the WIKI Setup for the UDRC-II whne I

Hi, When PTT is acting you should see red LED lighting on the side of activated connector either din-6 or hd15 of UDRC board. To check transmit you can use pbeacon on either channels like in sample

Make sure you have the right GPIO selected in the config. Also try running direwolf with sudo in case you have a permissions problem. This looks like your sound chip is good.

OK, so I am wondering in the dfault config, how does direwolf know which port (15 Pin or 6din) to use for that KISS port 8001 it sets up, and what if it's trying to use the 15 Pin? So I restored my

I am shifting gears from FLDIGI, can't get that package to work yet at all. Thought I would try VHF BBS's in the area, my local ARES BBS in this case. Using the default device for UDRC (not virtual

I don't have a UDRC-II but using a UDRC-I on a Pi2 the following works using the mini-din connector. Start alsamixer and check the following settings: PCM=20/20 ADC Leve=19/19 CM_L to = 10 Kohm CM_R

Updated script and instructions at https://github.com/nwdigitalradio/n7nix/tree/master/deviation-- John D. Hays K7VE PO Box 1223, Edmonds, WA 98020-1223

Basil Gunn <basil@...> wrote: I've updated the measure_deviation tone generating script & added a README.md. I verified the script with a UDRC & UDRC II with both din6 & hd15 cables. Please

Hi, I'm having a bit of trouble with my new UDRC-II. After installing/updating the Compass linux image and UDRC scripts yesterday, I configured Direwolf but was unable to transmit or decode any

Thanks to Stuart for pointing out that the AIC3204 is likely not completely dead as alsamixer appears to be working correctly. OK, now with a tone input I can check the pins on the AIC3204. Running

If you copy 9 lines, 134 thru 142, from case 1 and add them to case 2 such that you end up with this: ............................ ;; 1) # Validate tone frequency if [ "$1" -ge 10 -a "$1"

"John D Hays - K7VE" <john@...> wrote: I understand the argument parsing problem & will have a fix this morining. You should probably take the code off the wiki & we'll use github. You

Hey John, OK, cool... Was a little worried I needed to check the back for loose parts :-D Not sure what I can test next... Kinda stalled on being able to use the card at this point. I don't have the

That was an engineering change order and rework before shipping. -- John D. Hays K7VE PO Box 1223, Edmonds, WA 98020-1223

It does appear that a few locations were not masked and show signs of having had components mounted (the solder on these pads have depressions as if a part was there, not rounded as if they were not

Hey Corky, I rebooted, re-ran the UDRC soundcard initialization script, peaked with alsamizer to see the level were where they were when I first installed (check), then rebooted again just to make

If it's completely dead, you'd not be able to set mixer controls as the 'AIC3204 would not be responding to the I²C commands. If you can set the mixer without errors, then *something* is alive. It

OK, doing as Mike suggests, changing from 'plughw' to 'hw:CARD=udrc,DEV=0' appears to have gotten the tone generator running. I say appears because I still do not have any audio going over over the

Thanks for the additional information. I have an FT-817 at home that uses the same internal logic as the 857, so I can test it when I get there, but unfortunately, that will not be for a while. The