Ken, did you look at Draws manager? That has output adjustments . Also the power slider on the right of the wsjt-x screen can be adjusted. Rick. Ka4ohm

Did you try DRAWS ™ Manager? https://youtu.be/v5C3cWVVz_A You may want to also do a factory reset on the radio.

Hi. Im have set up my DRAWS hat/FT817 according to "temporarily Offline" youtube video. Install good WSJT-X good CAT good\ - PTT band change etc. RX good - waterfall/decode etc great. I set my WSJT-X

Doing an upgrade is not recommended for that beta image. -- John D. Hays Kingston, WA K7VE

Also ran these checks: pi@SpoobyDRAWS:~ $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: ALSA [bcm2835 ALSA], device 0: bcm2835 ALSA [bcm2835 ALSA] Subdevices: 7/7 Subdevice #0:

I started with a fresh write of beta 13 the other day that I configured and then check without issue. Only think I've done since is update and upgrade which ran into a kernel upgrade issue I've seen

Linux = open source = choices (;

I find the built in VNC to be pretty efficient and better than X11 -- John D. Hays Kingston, WA K7VE

Just an info note.  I found fldigi GUI response very poor to almost a "locked up" response when I was running it remotely via a ssh connection.  I changed the encryption algorithm on my command

Hi Jon, Can you tell me where you got the snd-soc-tlv320aic32x4-i2c.ko file and do you also need UDRC and snd-soc-tlv320aic32x4.ko? Is there a ax25.ko? Where do you put those files in /lib/modules?

Hi Wim, I would be interested to know what repeater you connected and if all went well to simultaneously use svxlink/echolink and direwolf/aprs on an RPi with Draws. Did you install and configure

Thanks Edd & Jim for verifying the changes I made. I appreciate your support. /Basil n7nix Jim Erickson <jim@...> writes:

Basil, after the update above, I ran prog_refresh.sh again and it updates as it should without the previous errors. It also updated XASTIR to a new version. It shows the correct GPSD version is

I didn’t save the output, but mine successfully detected that gpsd was a different version, downloaded the new version (3.19), compiled it and installed it in place. That appears to have fixed the

Here is the console output after git pull: pi@KD5MDRAWS:~/n7nix/gps $ ./gp_verchk.sh gp_verchk.sh: Detected gpsd package. gpsd: current version: 3.19, installed: 3.19 pi@KD5MDRAWS:~/n7nix/gps $

Edd, I made changes to both gp_verchk.sh & gp_install.sh to correct problem parsing version string. Could you please execute the following console commands & send me the console output. cd cd

For the past week or more, if I run the prog_refresh.sh script, it chooses to build GPSD (again) and ends with the following: Setup default gpsd file Setup default chrony.conf file Synchronizing

Thanks for the confirmation Jim and John. I think I will get the 3B+ as I run completely off of solar power and the 3B+ will use less power than the 4. 73 N1ESE

DRAWS™ is decoding FT8 and other signals just fine on the Raspberry Pi 3 (B/B+) without even challenging CPU utilization. If other groups are reporting problems, it may have more to do with the

They all work fine on my Pi 3B+. I also just did a ./prog_refresh.sh this morning and got the latest WSJT-X 2.1 installed. Haven’t tried decoding FT-8 with the latest version, but has worked fine