I really hope I can get the discounted early adopters case I ordered last April. Or it would be nice to know if we will ever get the case. I wanted for its emi shielding and power port. Cases for

Here are the outputs pi@k6jus:~/n7nix $ piver.sh Pi 3 Model B+ Mfg by Sony UK Has WiFi pi@k6jus:~/n7nix $ udrcver.sh Found a DRAWS HAT ID EEPROM Name: hat Product: Digital Radio

Rob, Lets confirm that measure_deviate.sh is working properly. Could you please cut & paste the console output of all the commands below. piver.sh udrcver.sh # Using o-scope check both left &

well today I made a din brakeout cable to test the audio to the ft-817 with a o-scope and using ./measure_deviate.sh -c left there is no audio on pin 3 or any other pin. I tested with pin 6 connected

I am happy to report that after many frustrating evenings puzzling out the setup of my first generation DRAWS hat I made a contact! PSK31, FLDIGI 4.1.03, Alinco DX70TH, T2FD antenna, homebuilt cable.

Sounds great, Basil! We currently have 9600 APRS available with satellite FalconSat-3, so I'll give that a try when there's a favorable pass. With the volume of cubesats being deployed these days,

Scott, Great to hear your success!! Motivates me to play with my projects! I have a nice 9600 baud demo with DRAWS using P2P paclink-unix that I'll be showing at Summer Gathering next

thanks Jim but the radio will go into transmit but no power out there is not enough drive to show any power out . it has to be a audio problem Rob k6jus

Hi everyone. Just wanted to share that I was able to get digipeated this morning via satellite "AISAT-1" as it passed over the U.S. East Coast. With an FT-857d connected to the DRAWS & up/down freqs

I believe with WSJTX you need to use CAT control to trigger the PTT as WSJTX does not have a GPIO option. I would test your setup with FLDIGI and see if you can get it to trigger your radio as it has

well tried it all over with a signal link and the transmitter works then plugged in the hat and not enough audio to drive the radio so it can be the radio and look like I am dead in the water. I have

Hi Frank, Is there a version number we should be looking for where the problem exists (or ceases to exist)? Will be very helpful when supporting others. See below, there may be some specific

Hi Jonathan, You are the MAN! You managed to reproduce the problem that NW Digital denies exits and have a work around! All the people that say you do not need the dtoverlay= line in config.txt

Great write-up, Mike! Thanks so much for putting that all together in one summary. FYI, I am still using the "draws_beta13.zip" image from http://nwdig.net/downloads/ on a Pi 3 B+ connected to an

Hi Jonathan, all. I'm puzzled by your "dtoverlay=" observation as that certainly was not required on either my Pi3 or Pi4 running the same Buster image. I wonder if some of the confusion has to do

Rob, you are contributing to the advances of mankind. Think of your purchase as an investment in progress. I follow this conversation daily. I ordered mine in early Spring- as soon as presales were

Hi I just wanted to let the group know that I have made good progress. I started from scratch with a clean buster image and using my Pi3B (to rule out any issues specific to my PI4). With just the out

just did a rest on the radio and still no transmit powers and also don't see how it can be the radio if it works with other soundcards. just tried the setalsa-ft817.sh command again no joy I have also

The FT-817 is probably the most tested for the DRAWS™ HAT. Are you using the left DIN-6 port and selecting the same in your program? There is a possibility that one of the flags in the CODEC was set

And make sure the lines are added at the end of /boot/config.txt in that order. dtoverlay=draws,alsaname=udrc force_turbo=1 -- John D. Hays Kingston, WA K7VE