It sounds like you have a 'production' version. See http://nwdigitalradio.com/draws-cases-have-shipped/ Pinout information is at https://nw-digital-radio.groups.io/g/udrc/files/DRAWSTech.pdf Software

Hi Some time back I purchased the hat and have left it sitting on my bench and now I would like to do something with it. The version I have slightly differs from the page photo, the power plug is

Happy to hear that you have it working Jakob! aa0jr de n7nix

Thanks Basil, I get input and output signals! That means it is working now with fldigi. CAT with flrig. I will observe it and do the final finetuning. Thanks again and 73 de jakob, aa0jr

Yes, tracking number are sent when we ship.

For Sale Early Adopter DRAWS Hat kit with Raspberry Pi 3, GPS Antenna, 2 Mini DIN-6 M/M 2m cables, power connector and clear case $250. ThumbDV $100.00 #earlyadopter #forsale

I have an early adopter kit with a Raspberry Pi 3, GPS Antenna, 2 Mini DIN-6 M?M 2m cables with power connector for sale for $250 and a ThumbDV for $100.00

Good! The ALSA control values are incorrect. If you run the following script in a console that should get you close. setalsa-ft817.sh Is your radio a Yaesu FT-817 or an FT818? You mention both.

Will we be getting an email with our tracking number?

Hi Basil, Now the NWDR image is up and running. I followed the WIKI instructions up to the fldigi installation and setup. When I arrived at the output gain adjustment with the fldigi Tune function,

Hi Jim, Woow, I rode the wrong horse! I was totally unaware of that. I did not realize that there is a difference between HamPi and the NWDR image. Let me do the download and installation. Will see

No, you are clearly using the HamPi image (which is an abomination imho). Basil is asking you to use the NW Digital DRAWS image, designed specifically for the DRAWS hat. It can

Hi Basil, Here is what I did so far: 1. I downloaded the file HamPi_v1.2a.img.xz on 1/21 2. I extracted it and got a folder with the file HamPi_v1.2a.img 3. I formatted a brand new 64 GB Micro SD

Below is what you will get if you do NOT use the NWDR image and follow the 'Getting Started' guide. pi@hampi:~ $ udrcver.sh bash: udrcver.sh: command not found pi@hampi:~ $ showudrc.sh bash:

Basil, here is what I got: pi@hampi:~ $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1] Subdevices: 4/4 Subdevice #0:

Until you have a successful setup use the NWDR image and follow the 'Getting Started Guide' in the UDRC wiki. https://nw-digital-radio.groups.io/g/udrc/wiki/8921 Focus on one program, FLdigi, and get

Thanks Corky and John for coming back on this issue. Yes, I have interrupted line 6 of the cable time ago. I saw these instructions somewhere.

As Corky says, modify the 6 pin cable. The FT-817 is one of the most tested units with DRAWS™ and works quite well. -- John D. Hays Kingston, WA K7VE

Are you using a 6-pin cable that has pin 6 connected? If so you will likely need to follow the instructions for removing that pin as the Yaesu radios take pin 6 as an input in addition to using it as

I installed the HamPi 1.2 on a Raspberry 4B 4GB and a DRAWS hat installed. I can't make it run with Wsjt-x or Fldigi with the FT-817 (FT-818). At this time I want to run it on 20 to 40 meter