Date   

Re: DRAWS

Paul Noa
 

On Tue, Apr 7, 2020 at 03:46 PM, Basil Gunn wrote:
./iptable-check.sh
Here it is today Basil:

/home/pi/n7nix/iptables# ./iptable-up.sh
root@asawizard:/home/pi/n7nix/iptables# ./iptable-check.sh
iptables file: /etc/iptables/rules.ipv4.ax25 exists
iptables file: /lib/dhcpcd/dhcpcd-hooks/70-ipv4.ax25 exists
Chain INPUT (policy ACCEPT 68 packets, 4478 bytes)
    pkts      bytes target     prot opt in     out     source               destination
 
Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
    pkts      bytes target     prot opt in     out     source               destination
 
Chain OUTPUT (policy ACCEPT 45 packets, 3377 bytes)
    pkts      bytes target     prot opt in     out     source               destination
       0        0 DROP       2    --  *      ax0     0.0.0.0/0            224.0.0.22
       0        0 DROP       udp  --  *      ax0     0.0.0.0/0            224.0.0.251          udp dpt:5353
       0        0 DROP       udp  --  *      ax0     0.0.0.0/0            239.255.255.250      udp
       0        0 DROP       2    --  *      ax1     0.0.0.0/0            224.0.0.22
       0        0 DROP       udp  --  *      ax1     0.0.0.0/0            224.0.0.251          udp dpt:5353
       0        0 DROP       udp  --  *      ax1     0.0.0.0/0            239.255.255.250      udp
root@asawizard:/home/pi/n7nix/iptables#
# hear is the problem: "Failed to load ax25 device" but not sure what to do about it:
~/n7nix/debug $ ax25-status -d
AX25 Debug Status
== failed & loaded but inactive units==
0 loaded units listed.
To show all installed unit files use 'systemctl list-unit-files'.
 
== direwolf ==
  pid: 473
  ver: Dire Wolf DEVELOPMENT version 1.6 D (Jan  6 2020)
== /proc/sys ==
ax25  core  ipv4  ipv6  netfilter  unix
ax0  ax1
 
== Network Interface ax0 & ax1 ==
4: ax0: <BROADCAST,UP,LOWER_UP> mtu 255 qdisc pfifo_fast state UNKNOWN group default qlen 10
    link/ax25 96:9e:68:84:86:b4:14 brd a2:a6:a8:40:40:40:00
    inet 192.168.255.2/32 brd 192.168.255.255 scope global ax0
       valid_lft forever preferred_lft forever
 
5: ax1: <BROADCAST,UP,LOWER_UP> mtu 255 qdisc pfifo_fast state UNKNOWN group default qlen 10
    link/ax25 96:9e:68:84:86:b4:02 brd a2:a6:a8:40:40:40:00
    inet 192.168.255.3/32 brd 192.168.255.255 scope global ax1
       valid_lft forever preferred_lft forever
 
== status networkd services ==
enabled
● systemd-networkd-wait-online.service - Wait for Network to be Configured
   Loaded: loaded (/lib/systemd/system/systemd-networkd-wait-online.service; enabled; vendor preset: enabled)
   Active: active (exited) since Wed 2020-04-08 08:39:00 EDT; 51min ago
     Docs: man:systemd-networkd-wait-online.service(8)
  Process: 470 ExecStart=/lib/systemd/systemd-networkd-wait-online (code=exited, status=0/SUCCESS)
 Main PID: 470 (code=exited, status=0/SUCCESS)
 
Apr 08 08:39:00 asawizard systemd-networkd-wait-online[470]: ignoring: lo
Apr 08 08:39:00 asawizard systemd-networkd-wait-online[470]: ignoring: lo
Apr 08 08:39:00 asawizard systemd-networkd-wait-online[470]: ignoring: lo
Apr 08 08:39:00 asawizard systemd-networkd-wait-online[470]: ignoring: lo
Apr 08 08:39:00 asawizard systemd-networkd-wait-online[470]: ignoring: lo
Apr 08 08:39:00 asawizard systemd-networkd-wait-online[470]: ignoring: lo
Apr 08 08:39:00 asawizard systemd-networkd-wait-online[470]: ignoring: lo
Apr 08 08:39:00 asawizard systemd-networkd-wait-online[470]: ignoring: lo
Apr 08 08:39:00 asawizard systemd-networkd-wait-online[470]: ignoring: lo
Apr 08 08:39:00 asawizard systemd[1]: Started Wait for Network to be Configured.
enabled
● systemd-networkd.service - Network Service
   Loaded: loaded (/lib/systemd/system/systemd-networkd.service; enabled; vendor preset: enabled)
   Active: active (running) since Wed 2020-04-08 08:38:59 EDT; 51min ago
     Docs: man:systemd-networkd.service(8)
 Main PID: 305 (systemd-network)
   Status: "Processing requests..."
    Tasks: 1 (limit: 2200)
   Memory: 4.3M
   CGroup: /system.slice/systemd-networkd.service
           └─305 /lib/systemd/systemd-networkd
 
Apr 08 08:38:58 asawizard systemd[1]: Starting Network Service...
Apr 08 08:38:59 asawizard systemd-networkd[305]: Enumeration completed
Apr 08 08:38:59 asawizard systemd[1]: Started Network Service.
Apr 08 08:39:00 asawizard systemd-networkd[305]: ax0: Gained carrier
Apr 08 08:39:00 asawizard systemd-networkd[305]: ax1: Gained carrier
Apr 08 08:39:05 asawizard systemd-networkd[305]: wlan0: Gained carrier
Apr 08 08:39:07 asawizard systemd-networkd[305]: wlan0: Gained IPv6LL
 
== status direwolf service ==
enabled
● direwolf.service - Direwolf Daemon
   Loaded: loaded (/etc/systemd/system/direwolf.service; enabled; vendor preset: enabled)
   Active: active (running) since Wed 2020-04-08 08:38:59 EDT; 51min ago
  Process: 460 ExecStartPre=/bin/rm -f /tmp/kisstnc (code=exited, status=0/SUCCESS)
 Main PID: 473 (direwolf)
    Tasks: 15 (limit: 2200)
   Memory: 2.7M
   CGroup: /system.slice/direwolf.service
           └─473 /usr/bin/direwolf -t 0 -c /etc/direwolf.conf -p
 
Apr 08 09:29:46 asawizard direwolf[473]: Position, DIGI (white center), Open Track
Apr 08 09:29:46 asawizard direwolf[473]: N 30 40.1100, W 083 19.0500
Apr 08 09:29:46 asawizard direwolf[473]: S.G.R.A. - APRS - DIGIPEATER- LAKEPARK, GA
Apr 08 09:30:08 asawizard direwolf[473]: [ig>tx] WC4PEM-10>APMI06,TCPIP*,qAC,SEVENTH::WC4PEM-10:PARM.Temp,Vin,Dg1h,Rx1…,I2,I3,I4
Apr 08 09:30:08 asawizard direwolf[473]: [ig>tx] WC4PEM-10>APMI06,TCPIP*,qAC,SEVENTH::WC4PEM-10:UNIT.C,Volt,Pkt,Pkt,Pc…,Hi,Hi,Hi
Apr 08 09:30:08 asawizard direwolf[473]: [ig>tx] WC4PEM-10>APMI06,TCPIP*,qAC,SEVENTH::WC4PEM-10:EQNS.0,.5,-64,0,0.075,…0,0,0,1,0
Apr 08 09:30:10 asawizard direwolf[473]: [ig>tx] WC4PEM-10>APMI06,TCPIP*,qAC,SEVENTH::WC4PEM-10:BITS.11111111,Bartow
Apr 08 09:30:18 asawizard direwolf[473]: [ig>tx] WC4PEM-10>APMI06,TCPIP*,qAC,SEVENTH:T#197,186,220,045,136,077,00000000
Apr 08 09:30:50 asawizard systemd[1]: /etc/systemd/system/direwolf.service:10: DefaultInstance= only makes sense for t…ignoring.
Apr 08 09:30:50 asawizard systemd[1]: /etc/systemd/system/direwolf.service:10: DefaultInstance= only makes sense for t…ignoring.
Hint: Some lines were ellipsized, use -l to show in full.
 
== status ax25 service ==
enabled
● ax25dev.service - AX.25 device
   Loaded: loaded (/etc/systemd/system/ax25dev.service; enabled; vendor preset: enabled)
   Active: active (exited) since Wed 2020-04-08 08:39:01 EDT; 51min ago
  Process: 565 ExecStart=/bin/bash -c /etc/ax25/ax25-upd (code=exited, status=0/SUCCESS)
 Main PID: 565 (code=exited, status=0/SUCCESS)
    Tasks: 3 (limit: 2200)
   Memory: 2.1M
   CGroup: /system.slice/ax25dev.service
           ├─588 /usr/local/sbin/mkiss /tmp/kisstnc /dev/ptmx /dev/ptmx
           ├─602 /usr/local/sbin/kissattach /dev/pts/1 udr0 192.168.255.2
           └─612 /usr/local/sbin/kissattach /dev/pts/2 udr1 192.168.255.3
 
Apr 08 08:39:00 asawizard bash[565]: ax25dev-parms: Using Device = ax0, baudrate: 1200
Apr 08 08:39:00 asawizard bash[565]: ax25dev-parms: finished
Apr 08 08:39:00 asawizard bash[565]:  Port udr0 attached to ax0
Apr 08 08:39:00 asawizard bash[565]: ax25dev-parms: baudrate: 1200
Apr 08 08:39:00 asawizard bash[565]: debug: using T1_TIMEOUT: 3000, T2_TIMEOUT: 1000
Apr 08 08:39:00 asawizard bash[565]: ax25dev-parms: Using Device = ax1, baudrate: 1200
Apr 08 08:39:00 asawizard bash[565]: ax25dev-parms: finished
Apr 08 08:39:00 asawizard bash[565]:  Port udr1 attached to ax1
Apr 08 08:39:01 asawizard bash[565]: ax25-upd script finished
Apr 08 08:39:01 asawizard systemd[1]: Started AX.25 device.
 
-- Logs begin at Wed 2020-04-08 08:38:56 EDT, end at Wed 2020-04-08 09:30:50 EDT. --
Apr 08 08:38:59 asawizard systemd[1]: Starting AX.25 device...
Apr 08 08:38:59 asawizard bash[480]: ax25-upd: Start Port udr0 with device /tmp/kisstnc
Apr 08 08:38:59 asawizard bash[480]: Direwolf serial port NOT FOUND
Apr 08 08:38:59 asawizard systemd[1]: ax25dev.service: Main process exited, code=exited, status=1/FAILURE
Apr 08 08:38:59 asawizard systemd[1]: ax25dev.service: Failed with result 'exit-code'.
Apr 08 08:38:59 asawizard systemd[1]: Failed to start AX.25 device.
Apr 08 08:39:00 asawizard systemd[1]: Starting AX.25 device...
Apr 08 08:39:00 asawizard bash[565]: ax25-upd: Start Port udr0 with device /tmp/kisstnc
Apr 08 08:39:00 asawizard bash[565]: Direwolf serial port ready
Apr 08 08:39:00 asawizard bash[565]: UDRC II or DRAWS installed
Apr 08 08:39:00 asawizard bash[565]: using mkiss with UDRC II and pseudo term_1: /dev/pts/1 pseudo term_2: /dev/pts/2
Apr 08 08:39:00 asawizard bash[565]: ax25dev-parms: baudrate: 1200
Apr 08 08:39:00 asawizard bash[565]: debug: using T1_TIMEOUT: 3000, T2_TIMEOUT: 1000
Apr 08 08:39:00 asawizard bash[565]: ax25dev-parms: Using Device = ax0, baudrate: 1200
Apr 08 08:39:00 asawizard bash[565]: ax25dev-parms: finished
Apr 08 08:39:00 asawizard bash[565]:  Port udr0 attached to ax0
Apr 08 08:39:00 asawizard bash[565]: ax25dev-parms: baudrate: 1200
Apr 08 08:39:00 asawizard bash[565]: debug: using T1_TIMEOUT: 3000, T2_TIMEOUT: 1000
Apr 08 08:39:00 asawizard bash[565]: ax25dev-parms: Using Device = ax1, baudrate: 1200
Apr 08 08:39:00 asawizard bash[565]: ax25dev-parms: finished
Apr 08 08:39:00 asawizard bash[565]:  Port udr1 attached to ax1
Apr 08 08:39:01 asawizard bash[565]: ax25-upd script finished
Apr 08 08:39:01 asawizard systemd[1]: Started AX.25 device.
 
== status ax25 path ==
enabled
● ax25dev.path
   Loaded: loaded (/etc/systemd/system/ax25dev.path; enabled; vendor preset: enabled)
   Active: active (running) since Wed 2020-04-08 08:38:58 EDT; 51min ago
 
Apr 08 08:38:58 asawizard systemd[1]: Started ax25dev.path.
 
== status ax25-mheardd ==
enabled
● ax25-mheardd.service - AX.25 mheard daemon
   Loaded: loaded (/etc/systemd/system/ax25-mheardd.service; enabled; vendor preset: enabled)
   Active: active (running) since Wed 2020-04-08 08:39:01 EDT; 51min ago
 Main PID: 705 (mheardd)
    Tasks: 1 (limit: 2200)
   Memory: 232.0K
   CGroup: /system.slice/ax25-mheardd.service
           └─705 /usr/local/sbin/mheardd -f -n 150
 
Apr 08 08:39:01 asawizard systemd[1]: Started AX.25 mheard daemon.
 
== status ax25d ==
enabled
● ax25d.service - General purpose AX.25 daemon
   Loaded: loaded (/etc/systemd/system/ax25d.service; enabled; vendor preset: enabled)
   Active: active (running) since Wed 2020-04-08 08:39:01 EDT; 51min ago
 Main PID: 707 (ax25d)
    Tasks: 1 (limit: 2200)
   Memory: 416.0K
   CGroup: /system.slice/ax25d.service
           └─707 /usr/local/sbin/ax25d -l
 
Apr 08 08:39:01 asawizard systemd[1]: Started General purpose AX.25 daemon.
Apr 08 08:39:01 asawizard ax25d[707]: starting
Apr 08 08:39:01 asawizard ax25d[707]: ax25d: UID for user 'rmsgw' is unknown, ignoring entry
Apr 08 08:39:01 asawizard ax25d[707]: new config file loaded successfuly
 
== netstat ax25 ==
Active AX.25 sockets
Dest       Source     Device  State        Vr/Vs    Send-Q  Recv-Q
*          KO4BCZ-0   ax0     LISTENING    000/000  0       0
*          KO4BCZ-10  ax0     LISTENING    000/000  0       0


Re: DRAWS

Paul Noa
 

Hi Basil,

I have GPS lock now had to extend the length of the LNA and put it outside the window:
───────────────────────────────────────────┐┌──────────────────Seen 20/Used 15┐
│ Time:          2020-04-08T12:56:15.000Z   ││     PRN  Elev   Azim   SNR  Use │
│ Latitude:         30.41945000 N           ││GP     3  39.0  300.0  33.0   Y  │
│ Longitude:        81.92713500 W           ││GP     4  13.0  310.0  25.0   Y  │
│ Alt (HAE, MSL):    -23.294,     76.444 ft ││GP    14  54.0   84.0  32.0   Y  │
│ Speed:             0.00 mph               ││GP    16  44.0  193.0  44.0   Y  │
│ Track (true, var):    74.1,  -6.4     deg ││GP    22  50.0  267.0  47.0   Y  │
│ Climb:             0.00 ft/min            ││GP    26  76.0  159.0  47.0   Y  │
│ Status:         3D DGPS FIX (146 secs)    ││GP    29  11.0   67.0  33.0   Y  │
│ Long Err  (XDOP, EPX):  0.48, +/-  5.9 ft ││GP    31  54.0   24.0  46.0   Y  │
│ Lat Err   (YDOP, EPY):  0.62, +/-  7.6 ft ││GP    32  33.0  108.0  26.0   Y  │
│ Alt Err   (VDOP, EPV):  1.20, +/- 22.6 ft ││GL    65  25.0  330.0  43.0   Y  │
│ 2D Err    (HDOP, CEP):  0.80, +/- 12.5 ft ││GL    71  53.0  142.0  34.0   Y  │
│ 3D Err    (PDOP, SEP):  1.40, +/- 21.8 ft ││GL    72  71.0  340.0  45.0   Y  │
│ Time Err  (TDOP):       0.86              ││GL    73  32.0   28.0  47.0   Y  │
│ Geo Err   (GDOP):       1.66              ││GL    74  65.0  344.0  41.0   Y  │
│ ECEF X, VX:              n/a    n/a       ││GL    75  37.0  243.0  46.0   Y  │
│ ECEF Y, VY:              n/a    n/a       ││GP     1   4.0  248.0  29.0   N  │
│ ECEF Z, VZ:              n/a    n/a       ││GP    23   3.0  307.0  36.0   N  │
│ Speed Err (EPS):       +/- 10.3 mph       ││GP    25   2.0   37.0   0.0   N  │
│ Track Err (EPD):        n/a               ││SB    46  28.0  245.0  46.0   N  │
│ Time offset:           0.587 sec          ││GL    70   4.0  148.0   0.0   N  │
│ Grid Square:            EM90ak            ││                                 │
└───────────────────────────────────────────┘└─────────────────────────────────┘
./btest.sh -g
*** Running as user: pi ***
Verify gpsd is returning sentences: Sentence count: 3
Test nmea sentence: GPS nmea sentences OK

pi@asawizard:~/n7nix/debug $ ./btest.sh -P udr0
*** Running as user: pi ***
Send a message beacon
 Sent: /usr/local/sbin/beacon -c KO4BCZ-11 -d 'APUDR1 via WIDE1-1' -l -s udr0 :KO4BCZ :08 09:07:27 EDT KO4BCZ mesg_beacon test from host asawizard on port udr0 Seq: 0

pi@asawizard:~/n7nix/debug $ tail -f /var/log/direwolf/direwolf.log
Apr  8 09:07:06 asawizard direwolf[473]: Digipeater W4NAS audio level = 20(7/6)   [NONE]   __||||___
Apr  8 09:07:06 asawizard direwolf[473]: [0.3] WC4PEM-12>APN391,K4OZS-10,W4NAS*:$ULTW009300BF02CA9798279F000E8765000103E80062031B00000055<0x0d><0x0a>
Apr  8 09:07:06 asawizard direwolf[473]: Ultimeter, JEEP, Kantronics KPC-3 rom versions
Apr  8 09:07:06 asawizard direwolf[473]: wind 9.1 mph, direction 269, temperature 71.4, barometer 29.96, humidity 100
Apr  8 09:07:31 asawizard direwolf[473]: [0L] KO4BCZ-11>APUDR1,WIDE1-1::KO4BCZ   :08 09:07:27 EDT KO4BCZ mesg_beacon test from host asawizard on port udr0 Seq: 0M

# Something is wrong with my iGate connection (See above log output) in the past this is what I got in the direwolf log:

$ tail -f /var/log/direwolf/direwolf.log
Feb  8 14:20:33 ASAwizard direwolf[475]: Can't get address for IGate server noam.aprs2.net, Temporary failure in name resolution
Feb  8 14:20:38 ASAwizard direwolf[475]: Now connected to IGate server noam.aprs2.net (107.170.42.65)
Feb  8 14:20:38 ASAwizard direwolf[475]: Check server status here http://107.170.42.65:14501
Feb  8 14:20:43 ASAwizard direwolf[475]: [ig] # aprsc 2.1.4-g408ed49
Feb  8 14:20:43 ASAwizard direwolf[475]: [ig] # logresp KO4BCZ verified, server T2USANE

Paul
KO4BCZ


Re: NWDR15 Check

Ed Bloom, KD9FRQ
 

Basil,

Restated and named my system something new.  All the basic checks now seem to work. And I get local email back, AX25 Start and Stop desktop icon works.

YAAC icon works and started me on the path of setup/configuration. WSJT-X also started and let me start the configuration process. Did not check anything else yet expect Xastir.

Xastir does nothing.  On previous install attempt, I followed the GitHub directions and loaded Xastir that way and then icon worked.  Do I need to do that again?

Also, is there a script to add the split channel icon to the desktop?  I have a second DRAWS setup and I will gladly use it for HF and leave this current install as VHF.

Ed, KD9FRQ

On 4/7/2020 10:32 AM, Basil Gunn wrote:
PLU setup seemed to run successfully. I am getting an error in
Claws-Mail when sending.

*Account 'pi@localhost': Connecting to SMTP server smtp.draws:25...
*** smtp.draws:25: unknown host.
*** Error occurred while sending the message.
Did you use the following instructions to set up Claws-mail?
https://github.com/nwdigitalradio/n7nix/tree/master/email/claws

Note everything is already installed, just look at the configuration
notes.

What did I do wrong?
Most likely specified server address incorrectly.
Should be 'localhost' for both receiving & sending mail.

/Basil n7nix


Re: DRAWS

Paul Noa
 

I have always gotten a gps lock, but this occurred after relocating to my work shop.
but no lock yes I get a dozen or so satellites but no lock.
i have quit working for the day it’s dinner time on east coast. 

will respond tomorrow.
Paul


Re: DRAWS

Basil Gunn
 

Now that I am transmitting my GPS data is invalid:
Where is your GPS antenna located are you getting a lock?

Are you seeing any sentences coming out of gpsd?

gpsmon
cgps
gpspipe -r
gpspipe -w

https://github.com/nwdigitalradio/n7nix/blob/master/docs/VERIFY_CONFIG.md#check-gps

beacon test script has a gps verify option -g

./btest.sh -g
*** Running as user: pi ***
Verify gpsd is returning sentences: Sentence count: 3
Test nmea sentence: GPS nmea sentences OK

Have you ever gotten a lock for your gps?
Put the antenna up against a window or better yet stick it outside.


Re: DRAWS

Paul Noa
 

Basil,

Now that I am transmitting my GPS data is invalid:

~/n7nix/debug $ sudo su
root@asawizard:/home/pi/n7nix/debug# ./btest.sh -P udr0
GPS data not valid
gps data: $GNGLL,3006.4840,N,08128.8355,W,231434.000,V,N*4B
Read Invalid gps data read from gpsd, using canned values
Send a message beacon
 Sent: /usr/local/sbin/beacon -c KO4BCZ-11 -d 'APUDR1 via WIDE1-1' -l -s udr0 :KO4BCZ :07 19:14:34 EDT KO4BCZ mesg_beacon test from host asawizard on port udr0 Seq: 3
root@asawizard:/home/pi/n7nix/debug#

I also no longer have an iGate output either ?? Don't recall making any changes??

Any ideas, recommendations, admonitions??

Paul


Re: DRAWS

Paul Noa
 

Basil,

I called tech support at Icom and was told I probably needed solder the appropriate "coffee Bean". LOL

A solder bridge, D for Audio and F for data.  This is on the board where the accessory connector is plugged into for the rear access, J6.
 

Here its soldered:


After I soldered it I was able to adjust the alsa settings using measure_deviate this 2200Hz:


There is still something not right as I am not seeing my packets including raw packets at aprs.fi?

Paul
KO4BCZ


Re: DRAWS

Paul Noa
 

Here it Basil,

/var/log $ cat udr_install.log
2020 01 23 09:25:01 PST: SD image version: nwdr15
2019 09 19 10:53:06 PDT: image_install.sh: image install script START
2019 09 19 11:02:09 PDT: gp_install.sh: gps install script FINISHED
2019 09 19 11:03:22 PDT: core_install.sh: core install script FINISHED
2019 09 19 11:03:23 PDT: install.sh: systemd install script FINISHED
2019 09 19 11:03:23 PDT: app_install.sh: app install (core) script FINISHED
2019 09 19 11:04:41 PDT: install.sh: RMS Gateway updated
2019 09 19 11:05:00 PDT: iptable_install.sh: iptables install/config script FINISHED
2019 09 19 11:06:49 PDT: image_install.sh: paclink-unix basic install script FINISHED
2019 09 19 11:06:49 PDT: image_install.sh: postfix install script FINISHED
2019 09 19 11:06:50 PDT: image_install.sh: mutt install script FINISHED
2019 09 19 11:09:34 PDT: install.sh: fbb BBS install script FINISHED
2019 09 19 11:10:17 PDT: install.sh: YAAC install script FINISHED
2019 09 19 11:10:18 PDT: install.sh: DStar install script FINISHED
2019 09 19 11:11:08 PDT: install.sh: arim & ardop install script FINISHED
2019 09 19 11:35:35 PDT: hf_install.sh: HF program (ALL) install script FINISHED
2019 09 19 11:36:24 PDT: image_install.sh: image install script FINISHED
2019 09 19 14:25:15 PDT: install.sh: draws-manager install script START
2019 09 19 14:30:00 PDT: install.sh: draws-manager install script FINISHED
2019 09 19 15:00:47 PDT: xs_install.sh: Xastir install script FINISHED
2020 01 06 12:54:56 PST: gp_install.sh: gps install script FINISHED
2020 01 06 12:54:57 PST: gp_verchk.sh: gpsd program update script FINISHED
2020 01 06 13:16:35 PST: hf_install.sh: HF program (js8call) install script FINISHED
2020 01 06 13:16:53 PST: hf_install.sh: HF program (wsjtx) install script FINISHED
2020 01 06 13:18:19 PST: hf_install.sh: HF program (fllog) install script FINISHED
2020 01 06 13:18:20 PST: hf_verchk.sh: hf program update script FINISHED
2020 01 06 13:34:28 PST: xs_install.sh: Xastir install script FINISHED
2020 01 08 13:08:49 PST: install.sh: YAAC install script FINISHED
2020 01 19 08:40:32 PST: hf_install.sh: HF program (fldigi) install script FINISHED
2020 01 19 08:49:52 PST: hf_install.sh: HF program (flrig) install script FINISHED
2020 01 19 08:49:54 PST: hf_verchk.sh: hf program update script FINISHED
2020 01 19 11:32:37 PST: install.sh: fbb BBS install script FINISHED
2020 03 24 17:51:44 EDT: app_config.sh: core config script FINISHED
2020 03 24 17:53:28 EDT: app_config.sh: AX.25 config script FINISHED
2020 03 24 17:53:29 EDT: app_config.sh: direwolf config script FINISHED
2020 03 24 17:53:29 EDT: install.sh: systemd install script FINISHED
2020 03 24 17:53:31 EDT: config.sh: systemd config script FINISHED
2020 03 24 17:53:32 EDT: iptable_install.sh: iptables install/config script FINISHED
2020 03 24 17:53:44 EDT: app_config.sh: app config (core) script FINISHED
pi@asawizard:/var/log $

 $ cd n7nix/iptables
pi@asawizard:~/n7nix/iptables $ sudo su
root@asawizard:/home/pi/n7nix/iptables# ./iptable-up.sh
root@asawizard:/home/pi/n7nix/iptables# ./iptable-check.sh
iptables file: /etc/iptables/rules.ipv4.ax25 exists
iptables file: /lib/dhcpcd/dhcpcd-hooks/70-ipv4.ax25 exists
Chain INPUT (policy ACCEPT 66 packets, 4374 bytes)
    pkts      bytes target     prot opt in     out     source               destination  
 
Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
    pkts      bytes target     prot opt in     out     source               destination  
 
Chain OUTPUT (policy ACCEPT 44 packets, 3375 bytes)
    pkts      bytes target     prot opt in     out     source               destination  
       0        0 DROP       2    --  *      ax0     0.0.0.0/0            224.0.0.22     
       0        0 DROP       udp  --  *      ax0     0.0.0.0/0            224.0.0.251          udp dpt:5353
       0        0 DROP       udp  --  *      ax0     0.0.0.0/0            239.255.255.250      udp
       0        0 DROP       2    --  *      ax1     0.0.0.0/0            224.0.0.22     
       0        0 DROP       udp  --  *      ax1     0.0.0.0/0            224.0.0.251          udp dpt:5353
       0        0 DROP       udp  --  *      ax1     0.0.0.0/0            239.255.255.250      udp


Re: DRAWS

Basil Gunn
 

iptables is not running which makes me think ./app_config.sh core did
not complete properly. Please show me the contents of /var/log/udr_install.log
then turn on iptables by doing the following from a console:

cd
cd n7nix/iptables
sudo su
./iptable-up.sh
./iptable-check.sh

Also send the console output of all the above commands.


Paul Noa <pauljnoa@...> writes:

I have no idea how that happened except I do recall it happened when I opened the Draws Manager local host 8080.

$ iptable-check.sh
iptables file: /etc/iptables/rules.ipv4.ax25 exists
iptables file: /lib/dhcpcd/dhcpcd-hooks/70-ipv4.ax25 exists
Chain INPUT (policy ACCEPT 28 packets, 2014 bytes)
pkts bytes target prot opt in out source destination

Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination

Chain OUTPUT (policy ACCEPT 24 packets, 1730 bytes)
pkts bytes target prot opt in out source destination


Re: DRAWS

Paul Noa
 

I have no idea how that happened except I do recall it happened when I opened the Draws Manager local host 8080.

$ iptable-check.sh
iptables file: /etc/iptables/rules.ipv4.ax25 exists
iptables file: /lib/dhcpcd/dhcpcd-hooks/70-ipv4.ax25 exists
Chain INPUT (policy ACCEPT 28 packets, 2014 bytes)
    pkts      bytes target     prot opt in     out     source               destination
 
Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
    pkts      bytes target     prot opt in     out     source               destination
 
Chain OUTPUT (policy ACCEPT 24 packets, 1730 bytes)
    pkts      bytes target     prot opt in     out     source               destination

Which I have just repeated the problem by opening the Draws Manager local host 8080 and the radio begins to transmit until I power it down??
 tail -f /var/log/direwolf/direwolf.log
Apr  7 14:34:37 asawizard direwolf[11727]: [0L] KO4BCZ-10>QST:(UI cc=00, p/f=0)E<0x00><0x00><0xc3><0x18><0xc5>@<0x00><0x01><0x11><0xb0><0xbf><0xc0><0xa8><0xff><0x02><0xef><0xff><0xff><0xfa><0x84>I<0x07>l<0x00><0xaf><0x9f><0x15>M-SEARCH * HTTP/1.1<0x0d><0x0a>HOST: 239.255.255.250:1900<0x0d><0x0a>MAN: "ssdp:discover"<0x0d><0x0a>MX: 1<0x0d><0x0a>ST: urn:dial-multiscreen-org:service:dial:1<0x0d><0x0a>USER-AGENT: Chromium/78.0.3904.108 Linux<0x0d><0x0a><0x0d><0x0a>
Apr  7 14:34:37 asawizard direwolf[11727]: [0L] KO4BCZ-10>QST:(UI cc=00, p/f=0)F<0xc0><0x00>(<0x00><0x00>@<0x00><0x01><0x02>DN<0xc0><0xa8><0xff><0x02><0xe0><0x00><0x00><0x16><0x94><0x04><0x00><0x00>"<0x00><0xf9><0x02><0x00><0x00><0x00><0x01><0x04><0x00><0x00><0x00><0xe0><0x00><0x00><0xfb>
Apr  7 14:34:37 asawizard direwolf[11727]: [0L] KO4BCZ-10>QST:(UI cc=00, p/f=0)E<0x00><0x00>D<0xf4>I@<0x00><0x01><0x11><0xe4><0xb8><0xc0><0xa8><0xff><0x02><0xe0><0x00><0x00><0xfb><0x14><0xe9><0x14><0xe9><0x00>0<0xea><0xfc><0x00><0x00><0x00><0x00><0x00><0x01><0x00><0x00><0x00><0x00><0x00><0x00><0x0b>_googlecast<0x04>_tcp<0x05>local<0x00><0x00><0x0c><0x00><0x01>
Apr  7 14:34:37 asawizard direwolf[11727]: [0L] KO4BCZ-10>QST:(UI cc=00, p/f=0)E<0x00><0x00><0xc3><0x18><0xd8>@<0x00><0x01><0x11><0xb0><0xac><0xc0><0xa8><0xff><0x02><0xef><0xff><0xff><0xfa><0x84>I<0x07>l<0x00><0xaf><0x9f><0x15>M-SEARCH * HTTP/1.1<0x0d><0x0a>HOST: 239.255.255.250:1900<0x0d><0x0a>MAN: "ssdp:discover"<0x0d><0x0a>MX: 1<0x0d><0x0a>ST: urn:dial-multiscreen-org:service:dial:1<0x0d><0x0a>USER-AGENT: Chromium/78.0.3904.108 Linux<0x0d><0x0a><0x0d><0x0a>
Apr  7 14:34:38 asawizard direwolf[11727]: [0L] KO4BCZ-10>QST:(UI cc=00, p/f=0)E<0x00><0x00><0xc3><0x19>,@<0x00><0x01><0x11><0xb0>X<0xc0><0xa8><0xff><0x02><0xef><0xff><0xff><0xfa><0x84>I<0x07>l<0x00><0xaf><0x9f><0x15>M-SEARCH * HTTP/1.1<0x0d><0x0a>HOST: 239.255.255.250:1900<0x0d><0x0a>MAN: "ssdp:discover"<0x0d><0x0a>MX: 1<0x0d><0x0a>ST: urn:dial-multiscreen-org:service:dial:1<0x0d><0x0a>USER-AGENT: Chromium/78.0.3904.108 Linux<0x0d><0x0a><0x0d><0x0a>
Apr  7 14:34:40 asawizard direwolf[11727]: [0L] KO4BCZ-10>QST:(UI cc=00, p/f=0)E<0x00><0x00>D<0xf4><0xf9>@<0x00><0x01><0x11><0xe4><0x08><0xc0><0xa8><0xff><0x02><0xe0><0x00><0x00><0xfb><0x14><0xe9><0x14><0xe9><0x00>0<0xea><0xfc><0x00><0x00><0x00><0x00><0x00><0x01><0x00><0x00><0x00><0x00><0x00><0x00><0x0b>_googlecast<0x04>_tcp<0x05>local<0x00><0x00><0x0c><0x00><0x01>
Apr  7 14:34:44 asawizard direwolf[11727]: [0L] KO4BCZ-10>QST:(UI cc=00, p/f=0)F<0xc0><0x00>(<0x00><0x00>@<0x00><0x01><0x02>DN<0xc0><0xa8><0xff><0x02><0xe0><0x00><0x00><0x16><0x94><0x04><0x00><0x00>"<0x00><0xfa><0x02><0x00><0x00><0x00><0x01><0x03><0x00><0x00><0x00><0xe0><0x00><0x00><0xfb>
Apr  7 14:34:44 asawizard direwolf[11727]: [0L] KO4BCZ-10>QST:(UI cc=00, p/f=0)F<0xc0><0x00>(<0x00><0x00>@<0x00><0x01><0x02>DN<0xc0><0xa8><0xff><0x02><0xe0><0x00><0x00><0x16><0x94><0x04><0x00><0x00>"<0x00><0xfa><0x02><0x00><0x00><0x00><0x01><0x03><0x00><0x00><0x00><0xe0><0x00><0x00><0xfb>
Apr  7 14:34:46 asawizard direwolf[11727]: [1L] KO4BCZ-1>QST:(UI cc=00, p/f=0)F<0xc0><0x00>(<0x00><0x00>@<0x00><0x01><0x02>DM<0xc0><0xa8><0xff><0x03><0xe0><0x00><0x00><0x16><0x94><0x04><0x00><0x00>"<0x00><0xfa><0x02><0x00><0x00><0x00><0x01><0x03><0x00><0x00><0x00><0xe0><0x00><0x00><0xfb>
Apr  7 14:34:46 asawizard direwolf[11727]: [1L] KO4BCZ-1>QST:(UI cc=00, p/f=0)F<0xc0><0x00>(<0x00><0x00>@<0x00><0x01><0x02>DM<0xc0><0xa8><0xff><0x03><0xe0><0x00><0x00><0x16><0x94><0x04><0x00><0x00>"<0x00><0xfa><0x02><0x00><0x00><0x00><0x01><0x03><0x00><0x00><0x00><0xe0><0x00><0x00><0xfb>
Apr  7 14:36:03 asawizard direwolf[11727]: [ig>tx] WC4PEM-14>APMI06,TCPIP*,qAC,SEVENTH:@071836z2815.27N/08139.28W_127/003g006t084r000p000P000h51b10181
Apr  7 14:36:07 asawizard direwolf[11727]: [ig>tx] W4DNQ>APIN20,TCPIP*,qAC,T2CAEAST:!3013.31N/08209.84W#Macclenny digi/igate
Apr  7 14:36:17 asawizard direwolf[11727]: [ig>tx] WC4PEM-14>APMI06,TCPIP*,qAC,SEVENTH:{{I071836zU=16.0V,T=77.9F
Apr  7 14:36:57 asawizard direwolf[11727]: [ig>tx] WC4PEM-14>APMI06,TCPIP*,qAC,SEVENTH:T#245,179,210,033,088,073,00000000
Apr  7 14:37:04 asawizard direwolf[11727]: [ig>tx] KQ4KX>APWW10,TCPIP*,qAC,NINTH:/071837z2803.50N/08146.10W_086/002g004t088r000p000P000h52b10169



Re: DRAWS

Basil Gunn
 

3.) Having no prior experience I am not sure about some of the results could you look at my file of outputs and give me your insights please?
It doesn't appear your iptables loaded properly which might mean your
./app_config.sh core command didn't do what it was supposed to

You are trying to multicast IGMP protocol and Chromcast packets out the
ax.25 ports which is not a good thing. Please run the following command
and send me the console output.

iptable-check.sh

The following IGMP & Chromcast multicast packets should never be
transmitted on the ax.25 ports.

udr0: fm KO4BCZ-10 to QST ctl UI pid=CC(IP) len 195
IP: len 195 192.168.255.2->239.255.255.250 ihl 20 ttl 1 DF prot UDP
UDP: len 175 35800->1900 Data 167
0000 M-SEARCH * HTTP/1.1..HOST: 239.255.255.250:1900..MAN: "ssdp:disc
0040 over"..MX: 1..ST: urn:dial-multiscreen-org:service:dial:1..USER-
0080 AGENT: Chromium/78.0.3904.108 Linux....
udr0: fm KO4BCZ-10 to QST ctl UI pid=CC(IP) len 40
IP: len 40 192.168.255.2->224.0.0.22 ihl 24 ttl 1 tos 192 DF prot 2
0000 "............
udr1: fm KO4BCZ-1 to QST ctl UI pid=CC(IP) len 40
IP: len 40 192.168.255.3->224.0.0.22 ihl 24 ttl 1 tos 192 DF prot 2
0000 "............


Re: GPS Extender

 

For fixed location installs, I like these (they have a 5M cable).


On Tue, Apr 7, 2020 at 3:43 AM Ed Bloom, KD9FRQ via groups.io <ewbloom=verizon.net@groups.io> wrote:
My shack in the basement.  I only have two, 16x28 windows. Both have
very, very limited view of sky.

What GPS extender do you recommend and why?

Or could I put an SMA bulkhead connector through the wall and get more
SMA coax to connect the GPS unit?

Thanks, Ed, KD9FRQ






--
John D. Hays
Kingston, WA
K7VE

 


Re: NWDR15 Check

Basil Gunn
 

PLU setup seemed to run successfully. I am getting an error in
Claws-Mail when sending.

*Account 'pi@localhost': Connecting to SMTP server smtp.draws:25...
*** smtp.draws:25: unknown host.
*** Error occurred while sending the message.
Did you use the following instructions to set up Claws-mail?
https://github.com/nwdigitalradio/n7nix/tree/master/email/claws

Note everything is already installed, just look at the configuration
notes.

What did I do wrong?
Most likely specified server address incorrectly.
Should be 'localhost' for both receiving & sending mail.

/Basil n7nix


Re: DRAWS

Basil Gunn
 

2.) I have not yet set up transmit levels and suspect that is my next
challenge
Use measure_deviate.sh script
https://github.com/nwdigitalradio/n7nix/tree/master/deviation

Search groups.io messages for 'deviation'
https://nw-digital-radio.groups.io/g/udrc/search?q=deviation


Re: GPS Extender

Basil Gunn
 

What GPS extender do you recommend and why?
I use these:
https://www.amazon.com/gp/product/B00LXRQY9A/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
because cable length is 3 Meters

Or could I put an SMA bulkhead connector through the wall and get more
SMA coax to connect the GPS unit?


Re: Program Setup & Use Instructions

Basil Gunn
 

Ed Bloom, KD9FRQ via groups.io <ewbloom=verizon.net@groups.io> writes:

Where can I find the PLU and Xastir setup and use instructions for our
DRAWS?
For a DRAWS card using the left connector use Xastir port 1.
For a DRAWS card using the right connector use Xastir port 2.

Xastir is already installed, you only need to configure it.
https://github.com/nwdigitalradio/n7nix/tree/master/xastir

Xastir will start and I have entered the basic information. Now, how do
I get it to see the DRAWS and start receiving?
Configure interfaces: Interface -> Interface Control
Use Networked AGWPE localhost:8000
Networked GPS (via gpsd)

You could also use an ax.25 port AX.25 TNC udr0 but using Networked
AGWPE is a little easier.

Same for PLU (linked to Claws Mail).
For paclink-unix questions I recommend using their groups.io site
https://groups.io/g/paclink-unix/topics

How do I start a Peer to Peer session and keep it open?
The email client just composes & organizes your messages. If you want to
send peer-to-peer then after composing a message use
wl2kax25 -c <callsign-no-ssid>
ie.
wl2kax25 -c n7nix

Paclink-unix Peer-to-peer is always listening for your call sign
paclink-unix has 3 transports

wl2ktelnet - Internet
wl2kax25 - packet radio
wl2kserial - for SCS-PTCIIpro

How do I start a normal session to the local RMS Gateway?
wl2kax25 -c <callsign-with sid>
ie.
wl2kax25 -c n7nix-10

To find RMS Gateways near you run this script
rmslist.sh <integer_distance_in_miles> <maidenhead_grid_square>
ie.
rmslist.sh 30 CN88nl
Proximity file is: 2 hours 2 minute(s), 9 seconds old
Using distance of 30 miles & grid square CN88NL

Callsign Frequency Distance Baud
KF7FIT-10 223780000 0 1200
N7NIX-10 144910000 0 1200
K7KCA-10 440125000 3 1200
KE7KML-10 223780000 3 1200
AF4PM-10 145690000 4 1200
AF5TR-10 145690000 11 1200
AE7LW-10 145050000 16 1200
KD7X-10 145630000 16 1200
KI7ULA-10 145050000 16 1200
W7UMX-10 145630000 16 1200
W0QJM-10 145630000 19 1200
WA7GJZ-10 145630000 19 1200
WA7GJZ-10 145630000 19 1200
VE7SEP-10 145690000 23 1200
NG2G-10 144990000 26 1200
N7FDM-10 145050000 27 1200
N7FDM-10 146438000 27 1200
KB7TEC-10 144990000 28 1200
W7ECG-10 144930000 28 1200

There is some older paclink-unix information here:
http://bazaudi.com/plu/doku.php

Thanks, Ed, KD9FRQ


Re: DRAWS

Paul Noa
 

Hi Basil,

Me again!  I have had seemingly gotten most everything straighten out. Bryan helped.

Attached is a text of my current situation.  What I know is:
1.) My GPS receiver is not picking up because it is too far from the window not an issue now.
2.) I have not yet set up transmit levels and suspect that is my next challenge
3.) Having no prior experience I am not sure about some of the results could you look at my file of outputs and give me your insights please?

I will be checking the transmit side in the meantime.
Thanks for your support in advance!
Paul KO4BCZ


Re: GPS Extender

 

It is just coax with a voltage bias to power the antenna. Just follow common coax extension procedures. 

There are also antenna assemblies with longer coax. 

On Tue, Apr 7, 2020, 03:43 Ed Bloom, KD9FRQ via groups.io <ewbloom=verizon.net@groups.io> wrote:
My shack in the basement.  I only have two, 16x28 windows. Both have
very, very limited view of sky.

What GPS extender do you recommend and why?

Or could I put an SMA bulkhead connector through the wall and get more
SMA coax to connect the GPS unit?

Thanks, Ed, KD9FRQ





Program Setup & Use Instructions

Ed Bloom, KD9FRQ
 

Where can I find the PLU and Xastir setup and use instructions for our DRAWS?

Xastir will start and I have entered the basic information. Now, how do I get it to see the DRAWS and start receiving?

Same for PLU (linked to Claws Mail).  How do I start a Peer to Peer session and keep it open? How do I start a normal session to the local RMS Gateway?

Thanks, Ed, KD9FRQ


GPS Extender

Ed Bloom, KD9FRQ
 

My shack in the basement.  I only have two, 16x28 windows. Both have very, very limited view of sky.

What GPS extender do you recommend and why?

Or could I put an SMA bulkhead connector through the wall and get more SMA coax to connect the GPS unit?

Thanks, Ed, KD9FRQ