Date   

Setting Up PAT with the #draws

Ed Bloom, KD9FRQ
 

KM4ACK,

Do you have any suggestions on the IP Address for PAT with the DRAWS.

When I enter 0.0.0.0 I get an error when starting PAT (address already in use).

When I enter 0.0.0.0:8080 in the browser, I am given the DRAWS Manager web interface page when 0.0.0.0 is used in the config.

The same results are received when I use localhost in the config (address already in use and same web page).

I am connected directly to the Pi as I would be in the field (upcoming exercise).

Respectively,

Ed, KD9FRQ

On 8/25/2019 7:04 AM, km4ack wrote:
I have ARDOP setup and running with Pat on the DRAWS hat using beta 13. I've made a video tutorial, but need to edit before posting. It will release on my YouTube channel Tuesday Aug 27 at 1600 central.

73,
KM4ACK
Find me on YouTube


Re: DRAWS and Allstar?

 

DRAWS™ CODEC is available under ALSA (and pulseaudio), anyone who wants to try this should look at chan_alsa and app_rpt 

Can app_rpt do PTT and SQUELCH DETECT using Raspberry Pi GPIO pins?

On Tue, Jun 4, 2019 at 9:25 AM Steve KC1AWV <smiller@...> wrote:
So, I've given this some more thought. you could probably do this through chan_alsa, chan_oss, or chan_usrp depending on how DRAWS configures its sound card.

Easiest would be GNU Radio USRP, the set up would be similar to that as DVSwitch.

On Tue, Jun 4, 2019 at 12:17 PM Christopher AI6KG <ch@...> wrote:
The issue I see is not with the Allstar distribution, but rather getting DRAWS to show up as a compatible device for app_rpt.

Agreed.  This is essentially what I was asking.

-ch
73 de AI6KG


--
John D. Hays
Kingston, WA
K7VE

 


Re: Eureka!!!! She works perfectly!!

Chris Brown <tcbrown68@...>
 

I have had success sending and receiving on the 891 without removing pin 6.


Re: minimum install to get the DRAWS gps working?

Jonathan Magee
 

Hi Tom,
I have the gps working and I don't have the battery installed

Regards
Jonathan GI7KMC

On Sun, 8 Sep 2019 at 19:55, Tom Early <n7tae@...> wrote:
Silly me. I thought I only needed to install the CR1220 if I wanted the RTC to continue to operate while the power was off. Apparently, the battery has to be installed for the GPS to operate. The GPS sensitivity seems really good. The DRAWS pulled in 10 satellites within a minute of powering up and had my position and altitude exactly right. In the same location, my ID-51p2 takes significantly longer.


Re: minimum install to get the DRAWS gps working?

 

Silly me. I thought I only needed to install the CR1220 if I wanted the RTC to continue to operate while the power was off. Apparently, the battery has to be installed for the GPS to operate. The GPS sensitivity seems really good. The DRAWS pulled in 10 satellites within a minute of powering up and had my position and altitude exactly right. In the same location, my ID-51p2 takes significantly longer.


Re: #DRAWS PAT via DRAWS #draws

Ed Bloom, KD9FRQ
 

Thank you!!! I am interested in ARDOP via HF and ax25 on 2m.

On 9/8/2019 11:39 AM, K4KDR wrote:
Hi Ed!

PAT works extremely well on the Pi/DRAWS using telnet, ax25, & ARDOP.?? The following video walks through the setup and there are many others from the same author going in to more detail on particular aspects of the same:


-Scott,?? K4KDR

=====================

On Sun, Sep 8, 2019 at 9:14 AM Ed Bloom, KD9FRQ via Groups.Io <ewbloom=verizon.net@groups.io> wrote:
Has anyone setup PAT via DRAWS??? I have not seen this but admit I may
have missed it.

73s, Ed, KD9FRQ


Re: #DRAWS PAT via DRAWS #draws

K4KDR
 

Hi Ed!

PAT works extremely well on the Pi/DRAWS using telnet, ax25, & ARDOP.  The following video walks through the setup and there are many others from the same author going in to more detail on particular aspects of the same:


-Scott,  K4KDR

=====================


On Sun, Sep 8, 2019 at 9:14 AM Ed Bloom, KD9FRQ via Groups.Io <ewbloom=verizon.net@groups.io> wrote:
Has anyone setup PAT via DRAWS??? I have not seen this but admit I may
have missed it.

73s, Ed, KD9FRQ


Re: minimum install to get the DRAWS gps working?

 

If the antenna has a good view of the sky, the first startup can take a while. 

You can also restart the gpsd

sudo systemctl stop gpsd
sudo systemctl start gpsd

You can also stop gpsd and. 

cat /Dev/ttySC0

On Sun, Sep 8, 2019, 08:55 okiejim <kd6vpe@...> wrote:
Please don't take this wrong but have you hooked up an antenna to the draw hat gps connector?

On Sun, Sep 8, 2019 at 8:16 AM Tom Early <n7tae@...> wrote:
I just received my DRAWS and at this point in time, I am only interested in getting the GPS working. (I'm developing a new ThumbDV app for D-Star Routing and linking and want to use the GPS to update the user and station positions to aprs.) I would rather not use Compass until I full understand what my program needs to use the DRAWS gps.

I found the wiki page on "Setup GPSD for Time and Position" and am wondering about the statement "Ensure that the device tree and driver have been installed". How do I do that with resorting to Compass? I installed gpsd etc, and I see /dev/ttySC0 and /tty/pps on my system and systemctl reports that gpsd is running, but gpsmon is showing all zeros.

Thanks!


Re: minimum install to get the DRAWS gps working?

okiejim
 

Please don't take this wrong but have you hooked up an antenna to the draw hat gps connector?

On Sun, Sep 8, 2019 at 8:16 AM Tom Early <n7tae@...> wrote:
I just received my DRAWS and at this point in time, I am only interested in getting the GPS working. (I'm developing a new ThumbDV app for D-Star Routing and linking and want to use the GPS to update the user and station positions to aprs.) I would rather not use Compass until I full understand what my program needs to use the DRAWS gps.

I found the wiki page on "Setup GPSD for Time and Position" and am wondering about the statement "Ensure that the device tree and driver have been installed". How do I do that with resorting to Compass? I installed gpsd etc, and I see /dev/ttySC0 and /tty/pps on my system and systemctl reports that gpsd is running, but gpsmon is showing all zeros.

Thanks!


minimum install to get the DRAWS gps working?

 

I just received my DRAWS and at this point in time, I am only interested in getting the GPS working. (I'm developing a new ThumbDV app for D-Star Routing and linking and want to use the GPS to update the user and station positions to aprs.) I would rather not use Compass until I full understand what my program needs to use the DRAWS gps.

I found the wiki page on "Setup GPSD for Time and Position" and am wondering about the statement "Ensure that the device tree and driver have been installed". How do I do that with resorting to Compass? I installed gpsd etc, and I see /dev/ttySC0 and /tty/pps on my system and systemctl reports that gpsd is running, but gpsmon is showing all zeros.

Thanks!


#DRAWS PAT via DRAWS #draws

Ed Bloom, KD9FRQ
 

Has anyone setup PAT via DRAWS??? I have not seen this but admit I may have missed it.

73s, Ed, KD9FRQ


Re: UDRC/DRAWS audio driver? #audio #draws #udrc-ii #documentation

Art - KC7SDA
 

thanks! I'll double check and see what I'm doing wrong that it's not loading the driver.


Re: Eureka!!!! She works perfectly!!

Matt N7ROO
 

Do we need to remove pin 6 for FT-891s?


On Thu, Aug 29, 2019, 18:24 Michael Narges <mnarges23@...> wrote:
Thanks for the documentation of the DRAWS Hat! Several questions are answered here.  

Thanks, 

Mike WF8O 


Re: UDRC/DRAWS audio driver? #audio #draws #udrc-ii #documentation

 

The current (Buster) Raspbian has the driver built in. You don't need the DKMS for it. 


On Sat, Sep 7, 2019, 10:32 Art - KC7SDA <nouse4anick@...> wrote:
I've been looking around the site and I see mention of a udrc-dkms (I'm assuming thats the audio driver file for the udrc)

my question is there a repository somewhere that I could add to, say, raspbian and install the udrc driver with apt-get and run the scripts to install the board?

I've looked through the scripts and I thought there was a fix for when a distro-update broke the driver but I can't find it.

73
Art


UDRC/DRAWS audio driver? #audio #draws #udrc-ii #documentation

Art - KC7SDA
 

I've been looking around the site and I see mention of a udrc-dkms (I'm assuming thats the audio driver file for the udrc)

my question is there a repository somewhere that I could add to, say, raspbian and install the udrc driver with apt-get and run the scripts to install the board?

I've looked through the scripts and I thought there was a fix for when a distro-update broke the driver but I can't find it.

73
Art


Re: no transmit #wsjt-x

Rob Lapham
 

I was not upset about your responses I did every thing you said it was the lack of response from the office, and I think maybe
they should offer to test some of the unit people cant get the unit to work, but that is up to them. I am sending it back
maybe they will test it not that they will ever let me know.  on to other projects

73 k6jus 
 


Re: no transmit #wsjt-x

Ed Bloom, KD9FRQ
 

Please send the DRAWS to me, if you don't want to send it back to NWDR.

I'll give it a go since they did issue you the refund.

Ed, KD9FRQ

On 9/5/2019 7:56 PM, Rob Lapham wrote:
still no return contact from them. Its like when you have a problem with there card they forget you.
ill take it to pay pal Monday before its to late
Rob k6jus


Re: no transmit #wsjt-x

 

I think, if you go back and review, you will see that you have had quite a few responses over the last several days, trying to help you diagnose the problem.  Bryan processed the promised refund today. 

73

On Thu, Sep 5, 2019 at 5:56 PM Rob Lapham <ke6jus@...> wrote:
still no return contact from them. Its like when you have a problem with there card they forget you.
ill take it to pay pal Monday before its to late
Rob k6jus
_.
--
John D. Hays
Kingston, WA
K7VE

 


Re: no transmit #wsjt-x

 

Refund Issued

Thanks,
Bryan K7UDR


Re: Buster Image with DRAWS software

Frank Ivan
 

Hi Brian,

It reports 0x0204.

udrcver.sh shows:
Found a DRAWS

          HAT ID EEPROM
Name: hat
Product: Digital Radio Amateur Work Station
Product ID: 0x0004
Product ver: 0x0204
UUID: 2420cda1-931d-478c-80e5-d770f3346adb
Vendor: NW Digital Radio

Thanks - Frank - K0FEI