Date   
Re: GPS not working #gps #gpsd

Basil Gunn
 

Jeff,

The results from the showudrc.sh script indicate that it is either not
seated properly on the 40pin RPi header ie. not pushed down far enough
or off by 1 row OR your DRAWS hat has been damaged or is defective.

I made the changes that you made to your /boot/config.txt file by
putting these entries as the last 2 lines & my DRAWS worked as expected:

enable_uart=0
dtparam=audio=on

You could try eliminating these 2 lines which is the default
configuration and rebooting but I don't think that is your problem.

/Basil


Jeff Marden via Groups.Io <jmardensdl=netscape.net@groups.io> writes:

Hello Basil:

Here is what shows on the console upon run of showudrc.sh:

aplay: device_list:270: no soundcards found...
No LSB modules are available.
No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.

Attached is the output from the showudrc.sh run on my Beta 7 DRAWS setup.

Comments and questions welcome.

Thanks,

Re: GPS not working #gps #gpsd

Jeff Marden
 

Hello Basil:

Here is what shows on the console upon run of showudrc.sh:

aplay: device_list:270: no soundcards found...
No LSB modules are available.
No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.

Attached is the output from the showudrc.sh run on my Beta 7 DRAWS setup.

Comments and questions welcome.

Thanks,
--
Jeff Marden
N1JCM

Re: DRAWS Shout Out - Great Solution #earlyadopters #beta7

N9UMJ
 

echoing Mike's comments..NWD Keep up the great work

On Thu, Jan 17, 2019 at 8:14 AM Mike - KB0FX <mweilb@...> wrote:
Ladies and Gentlemen of NW Digital Radio,

I just want to the thank you for introducing the DRAWS Pi-Hat! I have greatly enjoyed working with the card and the beta software! Your tireless support is greatly appreciated!

73

Mike - KB0FX

DRAWS Shout Out - Great Solution #earlyadopters #beta7

Mike - KB0FX
 

Ladies and Gentlemen of NW Digital Radio,

I just want to the thank you for introducing the DRAWS Pi-Hat! I have greatly enjoyed working with the card and the beta software! Your tireless support is greatly appreciated!

73

Mike - KB0FX

Re: GPS not working #gps #gpsd

Basil Gunn
 

With the load of Beta7 I appear to have the same problem as described
by Christof. Same messages from Showudrc ( no sound card found, and
errors), and my /boot/config.txt does not have the "dtoverlay="
commented-out. Beta6 works OK without sound card issues.
Send me the output of the showudrc.sh command.
/Basil

Re: GPS not working #gps #gpsd

Jeff Marden
 

Hello Basil:

With the load of Beta7 I appear to have the same problem as described by Christof. Same messages from Showudrc ( no sound card found, and errors), and my /boot/config.txt does not have the "dtoverlay=" commented-out. Beta6 works OK without sound card issues.

Any other thoughts (Perhaps wait for Christof's results)?

Thanks,
--
Jeff Marden
N1JCM

Re: GPS not working #gps #gpsd

Basil Gunn
 

From your showudrc.sh console output you have a comment character in
front of 'dtoverlay=' in the second line from the bottom of
/boot/config.txt.

You need to have 'dtoverlay=' before 'dtoverlay=draws'
Please remove the comment character and reboot the RPi.

/Basil n7nix

oe8bck <christof.bodner@...> writes:

Hi Basil!

Thanks or your quick response!
---
pi@draws:~/bin $ ./showudrc.sh >../showudrc
No LSB modules are available.
No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
---
See attachement for the output of showudrc.sh

---
pi@draws:~/bin $ ls -al /dev/ttySC* /dev/pps*
ls: cannot access '/dev/ttySC*': No such file or directory
ls: cannot access '/dev/pps*': No such file or directory
---

Yes, I did the first steps, but not all of them as I do not have a radio attached, yet.

Obvisously, the HAT is not recognized, do I need the 12V supply?

Re: GPS not working #gps #gpsd

 

Hi Christof,

The 12VDC connection is not required, but highly recommended.  What are you using for the 5VDC power supply (it should be at least 2.5 A).

My quick look at your showudrc output didn't see anything that jumped out at me, but I will let Basil respond after he takes a look.   

Of course, do the usual verification that the DRAWS HAT is properly seated.  

On Wed, Jan 16, 2019 at 10:13 AM oe8bck <christof.bodner@...> wrote:
Hi Basil!

Thanks or your quick response!
---
pi@draws:~/bin $ ./showudrc.sh >../showudrc
No LSB modules are available.
No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
---
See attachement for the output of showudrc.sh

---
pi@draws:~/bin $ ls -al /dev/ttySC* /dev/pps*
ls: cannot access '/dev/ttySC*': No such file or directory
ls: cannot access '/dev/pps*': No such file or directory
---

Yes, I did the first steps, but not all of them as I do not have a radio attached, yet.

Obvisously, the HAT is not recognized, do I need the 12V supply?

73 de Christof



--


John D. Hays
Edmonds, WA
K7VE

   

Re: GPS not working #gps #gpsd

oe8bck
 

Hi Basil!

Thanks or your quick response!
---
pi@draws:~/bin $ ./showudrc.sh >../showudrc
No LSB modules are available.
No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
---
See attachement for the output of showudrc.sh

---
pi@draws:~/bin $ ls -al /dev/ttySC* /dev/pps*
ls: cannot access '/dev/ttySC*': No such file or directory
ls: cannot access '/dev/pps*': No such file or directory
---

Yes, I did the first steps, but not all of them as I do not have a radio attached, yet.

Obvisously, the HAT is not recognized, do I need the 12V supply?

73 de Christof

Re: GPIO Pass through #draws

Ed Bloom, KD9FRQ
 

Thank you.
 
Then I will build an HF set and UHF/VHF set.
 
Ed Bloom
ewbloom@...
Sent from Webmail access
 
 

-----Original Message-----
From: John D Hays - K7VE <john@...>
To: udrc <udrc@nw-digital-radio.groups.io>
Sent: Tue, Jan 15, 2019 1:46 pm
Subject: Re: [udrc] GPIO Pass through #draws

Ed,

There is no current plan for stacked DRAWS boards.

Many of the GPIO pins are dedicated and not available for stacked cards.  However, the DRAWS provides 2 four wire ports (Mini Din-6) and 4 USB ports (plus the 8 pin GPIO brought off the board to the exterior of a case) which allows for a wide variety of configurations. 

Within direwolf, you can configure the 2 radio ports to provide independent 1200 baud and 9600 baud connections.  As we get better support for virtual audio ports, more applications can use these two ports independently as well as running multiple packet modem data rates on a single port.

Because of the Raspberry Pi networking capabilities, building up larger arrays of applications are possible over Ethernet/WiFi/... using multiple Pi + DRAWS.


On Tue, Jan 15, 2019 at 11:25 AM Ed Bloom, KD9FRQ <ewbloom@...> wrote:
Are there plans to have the DRAWS use pass-through GPIO pins so two units can be stacked?  This would allow 1200 & 9600 packet as well as WinMor and ARDOP to all run from one control point.

Just wondering as I am starting work though getting my station active using DRAWS instead of a PC or PI-TNC.
_._,_



--


John D. Hays
Director

  

Re: GPIO Pass through #draws

 

Ed,

There is no current plan for stacked DRAWS boards.

Many of the GPIO pins are dedicated and not available for stacked cards.  However, the DRAWS provides 2 four wire ports (Mini Din-6) and 4 USB ports (plus the 8 pin GPIO brought off the board to the exterior of a case) which allows for a wide variety of configurations. 

Within direwolf, you can configure the 2 radio ports to provide independent 1200 baud and 9600 baud connections.  As we get better support for virtual audio ports, more applications can use these two ports independently as well as running multiple packet modem data rates on a single port.

Because of the Raspberry Pi networking capabilities, building up larger arrays of applications are possible over Ethernet/WiFi/... using multiple Pi + DRAWS.


On Tue, Jan 15, 2019 at 11:25 AM Ed Bloom, KD9FRQ <ewbloom@...> wrote:
Are there plans to have the DRAWS use pass-through GPIO pins so two units can be stacked?  This would allow 1200 & 9600 packet as well as WinMor and ARDOP to all run from one control point.

Just wondering as I am starting work though getting my station active using DRAWS instead of a PC or PI-TNC.
_._,_



--


John D. Hays
Director

  

GPIO Pass through #draws

Ed Bloom, KD9FRQ
 

Are there plans to have the DRAWS use pass-through GPIO pins so two units can be stacked?  This would allow 1200 & 9600 packet as well as WinMor and ARDOP to all run from one control point.

Just wondering as I am starting work though getting my station active using DRAWS instead of a PC or PI-TNC.

Mike - KB0FX
 

Fellow DRAWs Early Adopters,

I am happy to report I am making progress with getting the DRAWS card to work with the Kenwood TS-440S on HF digital modes. I have JS8Call & WSJT-X FT8 Mode decoding signals. I made an adapter cable with a 6 Pin DIN cable and a RJ-45 Jack Block that allows me to use my Signalink USB 13 pin DIN to RJ-45 Plug adapter cable to connect to the DRAWS Pi-Hat. 

I have included a picture below. Once I get everything working I will post the color code and pin out. 

73 - Mike - KB0FX

Re: GPS not working #gps #gpsd

Basil Gunn
 

Please send me the output of showudrc.sh
Look for it in your local bin directory
cd
cd bin
./showudrc.sh

Also send me the console output of:

ls -al /dev/ttySC* /dev/pps*

- Did you follow these instructions?
https://nw-digital-radio.groups.io/g/udrc/wiki/DRAWS%3A-Getting-Started

- Which image are you using: BETA7?

/Basil


oe8bck <christof.bodner@...> writes:

Hi,

I got my DRAWS last week after waiting 4 weeks on customs. Today I wanted to check XAstir, but GPS is not working:
---
pi@draws:~ $ sudo service gpsd status
● gpsd.service - GPS (Global Positioning System) Daemon
Loaded: loaded (/lib/systemd/system/gpsd.service; enabled; vendor preset: enabled)
Active: active (running) since Mon 2019-01-14 21:19:10 CET; 37s ago
Process: 1282 ExecStart=/usr/local/sbin/gpsd $GPSD_OPTIONS $OPTIONS $DEVICES (code=exited, status=0/SUCCESS)
Main PID: 1283 (gpsd)
CGroup: /system.slice/gpsd.service
└─1283 /usr/local/sbin/gpsd -n /dev/ttySC0 /dev/pps0

Jan 14 21:19:11 draws gpsd[1283]: gpsd:ERROR: SER: read-only device open of /dev/pps0 failed: No such file or directory
Jan 14 21:19:11 draws gpsd[1283]: gpsd:ERROR: initial GPS device /dev/pps0 open failed

GPS not working #gps #gpsd

oe8bck
 

Hi,

I got my DRAWS last week after waiting 4 weeks on customs. Today I wanted to check XAstir, but GPS is not working:
---
pi@draws:~ $ sudo service gpsd status
● gpsd.service - GPS (Global Positioning System) Daemon
   Loaded: loaded (/lib/systemd/system/gpsd.service; enabled; vendor preset: enabled)
   Active: active (running) since Mon 2019-01-14 21:19:10 CET; 37s ago
  Process: 1282 ExecStart=/usr/local/sbin/gpsd $GPSD_OPTIONS $OPTIONS $DEVICES (code=exited, status=0/SUCCESS)
 Main PID: 1283 (gpsd)
   CGroup: /system.slice/gpsd.service
           └─1283 /usr/local/sbin/gpsd -n /dev/ttySC0 /dev/pps0

Jan 14 21:19:11 draws gpsd[1283]: gpsd:ERROR: SER: read-only device open of /dev/pps0 failed: No such file or directory
Jan 14 21:19:11 draws gpsd[1283]: gpsd:ERROR: initial GPS device /dev/pps0 open failed
Jan 14 21:19:11 draws gpsd[1283]: gpsd:ERROR: SER: device open of /dev/ttySC0 failed: No such file or directory - retrying read-only
Jan 14 21:19:11 draws gpsd[1283]: gpsd:ERROR: SER: read-only device open of /dev/ttySC0 failed: No such file or directory
Jan 14 21:19:11 draws gpsd[1283]: gpsd:ERROR: /dev/ttySC0: device activation failed.
Jan 14 21:19:11 draws gpsd[1283]: gpsd:ERROR: /dev/ttySC0: activation failed, freeing device
Jan 14 21:19:11 draws gpsd[1283]: gpsd:ERROR: SER: device open of /dev/pps0 failed: No such file or directory - retrying read-only
Jan 14 21:19:11 draws gpsd[1283]: gpsd:ERROR: SER: read-only device open of /dev/pps0 failed: No such file or directory
Jan 14 21:19:11 draws gpsd[1283]: gpsd:ERROR: /dev/pps0: device activation failed.
Jan 14 21:19:11 draws gpsd[1283]: gpsd:ERROR: /dev/pps0: activation failed, freeing device
pi@draws:~ $ lsmod
Module                  Size  Used by
fuse                  110592  3
rfcomm                 49152  4
bnep                   20480  2
hci_uart               36864  1
btbcm                  16384  1 hci_uart
serdev                 20480  1 hci_uart
bluetooth             368640  29 hci_uart,bnep,btbcm,rfcomm
ecdh_generic           28672  1 bluetooth
xt_tcpudp              16384  4
ip6table_filter        16384  0
ip6_tables             24576  1 ip6table_filter
iptable_filter         16384  1
brcmfmac              307200  0
brcmutil               16384  1 brcmfmac
cfg80211              573440  1 brcmfmac
rfkill                 28672  6 bluetooth,cfg80211
snd_bcm2835            32768  1
snd_pcm                98304  1 snd_bcm2835
snd_timer              32768  1 snd_pcm
snd                    69632  5 snd_timer,snd_bcm2835,snd_pcm
uio_pdrv_genirq        16384  0
fixed                  16384  0
uio                    20480  1 uio_pdrv_genirq
ax25                   69632  0
i2c_dev                16384  0
ip_tables              24576  1 iptable_filter
x_tables               32768  5 ip_tables,iptable_filter,xt_tcpudp,ip6table_filter,ip6_tables
ipv6                  425984  38
---
Any idea what's wrong? I have just the USB plug as power connector. Do I need to attach a 12V supply?

73 de OE8BCK Christof

Re: Beta7 release announcement

Art - KC7SDA
 

awesome! after most of the bugs get worked out I'll do the same thing with my udrc and update everyone up here to the new image =)

Re: Beta7 release announcement

f6bvp
 

By the way, I wrote a patch for direwolf 1.5-1.6 to give the choice of
channel for sending calibration test signal (option -x).
This may be useful for the default is only on channel 0 that is right
connector (HD15) on UDRC II which is not very convenient when you
prefere to use Din6 wiring for the radio set. With DRAW hat you may also
choose to send calibration signal for level adjustment either on channel
0 or channel 1.

Basil, if interested by this patch I wrote a Direwolf issue here :
https://github.com/wb2osz/direwolf/issues/184
Patch can be downloaded from file :
https://github.com/wb2osz/direwolf/files/2703361/direwolf.patch2.txt

Bernard

Le 13/01/2019 à 00:46, Basil Gunn a écrit :

Art - KC7SDA <@nouse4anick> writes:

semi random question: does this beta work with the original udrc 2? I
think I really really need to update it to the newest drivers and
software.
I have tested the images with a UDRC II. Change /boot/config.txt
from: dtoverlay=draws
to: dtoverlay=udrc

Note *for a UDRC II* that the left & right connectors are swapped from a
DRAWS HAT ie. right connector(HD 15) is chan 0 & uses gpio 12 for PTT,
left connector (mDin6) is chan 1 & uses gpio 23

/Basil

Re: Beta7 release announcement

Basil Gunn
 

Art - KC7SDA <@nouse4anick> writes:

semi random question: does this beta work with the original udrc 2? I
think I really really need to update it to the newest drivers and
software.
I have tested the images with a UDRC II. Change /boot/config.txt
from: dtoverlay=draws
to: dtoverlay=udrc

Note *for a UDRC II* that the left & right connectors are swapped from a
DRAWS HAT ie. right connector(HD 15) is chan 0 & uses gpio 12 for PTT,
left connector (mDin6) is chan 1 & uses gpio 23

/Basil

Re: Beta7 release announcement

Art - KC7SDA
 

semi random question: does this beta work with the original udrc 2? I think I really really need to update it to the newest drivers and software.

Re: Beta7 release announcement

Art - KC7SDA
 

currently testing the beta, so far so good, everything is working great!