Great to hear you have some things working. Please know your problems & feed back are very important to us. I am using the wiki at groups.io now and if you check it out you should see I've made an att

#configuration #management #draws #direwolf #ax25

I want to configure wsjtx on the Pi DRAWS image to function with my TS590. I think I have two options. One is to use the usb connection and the CODEC that is part of the ts 590 and use a usb port on t

#draws #configuration

Hi Ed, We don’t know yet. As an owner of one of those radios, I am trying to figure out if this is the case. You may or may not need something else. Hope to have some answers fairly soon. NW Digital d

#draws #ic7000 #hfmodes

Merry Christmas Julian All of the adjustment I made to the receive signal was through the ADC Level of the alsa mixer. FLDIGI has a go no go "diamond shaped" icon on the bottom tool bar of the main sc

#setup #fldigi #draws

I would just like to take few minutes to thank everyone for their testing and feedback on the images that we have for the DRAWS™ HAT. We have key people at NW Digital Radio all looking at the feedback

#applications #beta #image #draws #support

Hi Art. were you able to get your ft-891 working properly with an HF radio using an HF digital mode? 73 Julian oh8stn

#setup #compassimage #draws #earlyadopters

I am having exactly the same problem with the Yaesu ft-891. I'm sure the solution is out there, but with all of the answers scattered through dozens of threads it's becoming extremely frustrating. has

#draws

Thanks John, I will try that. Keying the rig is not the problem though. I was using flrig with fldigi CAT only and it would go into transmit with no signal. When I checked GPIO 12 in fldigi and enable

#betaimage #setup #draws

Apologize for doing a subject reset. The original post was lost here. I think it was David [kg5eiu] who originally posted the request but the original does not seem to be in the UDRC subgroup. My orig

#draws #photos

Basil I understand now. Couldn't figure out why the RED PIPE was in the argument ./btest.sh -P [udrc0|udrc1] Thanks Joe K3JV

#betaimage #draws

We are using the S1216F8-GL Datasheet:

#draws #gps

I gave a talk about using the amateur radio IP network and a VPN at DCC this year. See: https://www.youtube.com/watch?v=OxsmGaFZ2MM&t=5s With or without the VPN, I like to operate sometimes away from

#mifi #draws #internet

Linux configuration by convention lives in /etc or /usr/local/etc direwolf config is here: /etc/direwolf.conf Just my preference: I found 7 inch screens, even the superior Sunfounder 1024x600 display

#draws #compass #dstar

Hold off unless you have an urgent need Anna is working on something.

#dstar #draws #compass

In the HAT spec, there’s room to put a chunk of device tree on a flash chip on the hardware itself. If the firmware sees this, it will load up that device tree overlay and merge it with the rest of th

#direwolf #draws

# Additional overlays and parameters are documented /boot/overlays/README force_turbo=1 dtoverlay=draws # Enable audio (loads snd_bcm2835) dtparam=audio=on results in: Audio device for both receive an

#draws #direwolf

All, Thanks for your patience on this thread – the problem was not self-evident and I don’t understand why the following situation works for me. The solution was to comment out all references to port

#xastir #direwolf #draws

In addition – if I use a direwolf.conf for the left port @ 1200 baud and PTT set to GPIO 12, exactly the same as below. PPT is proper timing with no sound. Grrr…. J – KD4IZ

#direwolf #draws #xastir

https://www.youtube.com/watch?v=8jzHA_cjuwM

#draws #setup #video

Robert Sears wrote on 12/11/18 06:38: Not an issue in my situation as I don't use the hinged stand on the smartipi case. I use the VESA mount instead. Nonetheless, I agree rearranging the connectors m

#draws #smartipi