Happy to hear that you have it working Jakob! aa0jr de n7nix

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

Thanks Basil, I get input and output signals! That means it is working now with fldigi. CAT with flrig. I will observe it and do the final finetuning. Thanks again and 73 de jakob, aa0jr

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

Good! The ALSA control values are incorrect. If you run the following script in a console that should get you close. setalsa-ft817.sh Is your radio a Yaesu FT-817 or an FT818? You mention both.

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

Hi Basil, Now the NWDR image is up and running. I followed the WIKI instructions up to the fldigi installation and setup. When I arrived at the output gain adjustment with the fldigi Tune function, I

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

Hi Jim, Woow, I rode the wrong horse! I was totally unaware of that. I did not realize that there is a difference between HamPi and the NWDR image. Let me do the download and installation. Will see if

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

No, you are clearly using the HamPi image (which is an abomination imho). Basil is asking you to use the NW Digital DRAWS image, designed specifically for the DRAWS hat. It can be found here: http://n

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

Hi Basil, Here is what I did so far: 1. I downloaded the file HamPi_v1.2a.img.xz on 1/21 2. I extracted it and got a folder with the file HamPi_v1.2a.img 3. I formatted a brand new 64 GB Micro SD with

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

Below is what you will get if you do NOT use the NWDR image and follow the 'Getting Started' guide. pi@hampi:~ $ udrcver.sh bash: udrcver.sh: command not found pi@hampi:~ $ showudrc.sh bash: showudrc.

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

Basil, here is what I got: pi@hampi:~ $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: b1 [bcm2835 HDMI 1], device 0: bcm2835 HDMI 1 [bcm2835 HDMI 1] Subdevices: 4/4 Subdevice #0: subdev

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

Until you have a successful setup use the NWDR image and follow the 'Getting Started Guide' in the UDRC wiki. https://nw-digital-radio.groups.io/g/udrc/wiki/8921 Focus on one program, FLdigi, and get

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

Thanks Corky and John for coming back on this issue. Yes, I have interrupted line 6 of the cable time ago. I saw these instructions somewhere.

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

As Corky says, modify the 6 pin cable. The FT-817 is one of the most tested units with DRAWS™ and works quite well.

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

Are you using a 6-pin cable that has pin 6 connected? If so you will likely need to follow the instructions for removing that pin as the Yaesu radios take pin 6 as an input in addition to using it as

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

I installed the HamPi 1.2 on a Raspberry 4B 4GB and a DRAWS hat installed. I can't make it run with Wsjt-x or Fldigi with the FT-817 (FT-818). At this time I want to run it on 20 to 40 meter shortwave

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

Hello Basil. I went ahead and updated as you instruct in this thread. As I did this, this message came up: authentication required to restart 'dphys-swapfile.service multiple identities can be used fo

#draws #wsjt-x

Happy that your setup is working for you! Have some fun. /Basil n7nix TG9AOR <qrz@...> writes:

#wsjt-x #ft-8

Basil, thank you for your response. I cycled the PWR slider: no change. I cycled the Output device on my audio tab, from plughw:CARD=udrc,DEV=0 Mono to default, and to Left on the drop down list box n

#wsjt-x #ft-8

Looking at my notes to see what might be relevant because I do not own an FT-450. * Re: FT-817, I could only get this radio to work by disconnecting pin 6 (squelch) on the mDin6 cable. https://github.

#wsjt-x #ft-8

Hello Friends. I have this setup on WSJT-X that came with the DRAWS Image (WSJT-X v2.0.1 7ddcb7) Radio Tab Audio Tab Rig: FT-450 Input plughw:CARD=udrc,DEV=0 Mono Serial Port /dev/ttyUSB0 Output plugh

#wsjt-x #ft-8

not using a draws yet, but i am using ham radio deluxe on my laptop and i have the settings as below, just remember for it to accept out of the data port, you need to tell it specifically to use the c

#wsjt-x #kenwood #flrig