|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
Mark J Culross <mjculross@...> writes: Have fun in your training class. I was trying to qualify your cable and I don't think that is where the problem lies. After verifying that my IC-706 ca
Mark J Culross <mjculross@...> writes: Have fun in your training class. I was trying to qualify your cable and I don't think that is where the problem lies. After verifying that my IC-706 ca
|
By
Basil Gunn
· #5197
·
|
|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
Basil (n7nix): Thanks for your most recent post. I am in a training class all week so I won't be able to get back to tinkering with my DRAWS until this weekend, but I'll definitely try to duplicate yo
Basil (n7nix): Thanks for your most recent post. I am in a training class all week so I won't be able to get back to tinkering with my DRAWS until this weekend, but I'll definitely try to duplicate yo
|
By
Mark J Culross
· #5196
·
|
|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
Corky (AF4PM): Thanks for your most recent post. I am in a training class all week so I won't be able to get back to tinkering with my DRAWS until this weekend, but I'll definitely try to duplicate yo
Corky (AF4PM): Thanks for your most recent post. I am in a training class all week so I won't be able to get back to tinkering with my DRAWS until this weekend, but I'll definitely try to duplicate yo
|
By
Mark J Culross
· #5195
·
|
|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
Mark, I hooked up the IC-7000 to the DRAWS today and tested the system for ax25 packet with Direwolf. I am using the radio on the right-hand miniDIN connector with the setalsa-ic7000.sh settings, whic
Mark, I hooked up the IC-7000 to the DRAWS today and tested the system for ax25 packet with Direwolf. I am using the radio on the right-hand miniDIN connector with the setalsa-ic7000.sh settings, whic
|
By
Corky Searls
· #5194
·
|
|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
Just finished a fresh install of nwdr17. Using the default ALSA settings, did not run any setalsa- script (ADC Level L:[0.00dB]), I was able to receive APRS packets on 2M using the mDin6 cable to the
Just finished a fresh install of nwdr17. Using the default ALSA settings, did not run any setalsa- script (ADC Level L:[0.00dB]), I was able to receive APRS packets on 2M using the mDin6 cable to the
|
By
Basil Gunn
· #5191
·
|
|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
I just did a verification using 2M (144.390) APRS on my IC-706MkIIG. I used both the 13 pin Aux socket & 6 pin miniDin socket connected to the left mDin6 connector on the DRAWS hat. I was able to rece
I just did a verification using 2M (144.390) APRS on my IC-706MkIIG. I used both the 13 pin Aux socket & 6 pin miniDin socket connected to the left mDin6 connector on the DRAWS hat. I was able to rece
|
By
Basil Gunn
· #5189
·
|
|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
Basil (n7nix): Thanks again for your reply. I am definitely using alsa-show.sh to confirm the settings as I make changes, both with alsamixer as well as with the DRAWS Manager. Here's the current capt
Basil (n7nix): Thanks again for your reply. I am definitely using alsa-show.sh to confirm the settings as I make changes, both with alsamixer as well as with the DRAWS Manager. Here's the current capt
|
By
Mark J Culross
· #5188
·
|
|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
Looking at Basil's response, I think he found the problem. With the IC-7000 the audio is very sensitive, but the HF and VHF paths are very different. The gain setting for HF will likely not provide su
Looking at Basil's response, I think he found the problem. With the IC-7000 the audio is very sensitive, but the HF and VHF paths are very different. The gain setting for HF will likely not provide su
|
By
Corky Searls
· #5187
·
|
|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
Update on discriminator below. Thanks, -Corky
Update on discriminator below. Thanks, -Corky
|
By
Corky Searls
· #5186
·
|
|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
Mark J Culross <mjculross@...> writes: In a console run this command: tail -f /var/log/direwolf/direwolf.log In another window run alsamixer for the udrc sound device Increase the ADC level
Mark J Culross <mjculross@...> writes: In a console run this command: tail -f /var/log/direwolf/direwolf.log In another window run alsamixer for the udrc sound device Increase the ADC level
|
By
Basil Gunn
· #5185
·
|
|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
Basil (n7nix): Thanks for your advice. I believe that I understand all of your instructions & have executed them as directed, but APRS RX is still not working. I did find that I could make quicker mod
Basil (n7nix): Thanks for your advice. I believe that I understand all of your instructions & have executed them as directed, but APRS RX is still not working. I did find that I could make quicker mod
|
By
Mark J Culross
· #5183
·
|
|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
First thanks for all the console output. This could be your problem since that script tries to set up deviation for the HF radio. You need to set deviation for the VHF/UHF radio in the IC-7000. I woul
First thanks for all the console output. This could be your problem since that script tries to set up deviation for the HF radio. You need to set deviation for the VHF/UHF radio in the IC-7000. I woul
|
By
Basil Gunn
· #5181
·
|
|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
Corky (AF4PM): Thanks again for your follow-up. My answers/comments are embedded below within [brackets]. Mark J Culross KD5RXT
Corky (AF4PM): Thanks again for your follow-up. My answers/comments are embedded below within [brackets]. Mark J Culross KD5RXT
|
By
Mark J Culross
· #5180
·
|
|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
Mark, yes the script is set up for IN2 as the primary use for the IC-7000 was for HF. It has been a while since I used it for VHF with the DRAWS and I have not tried the latest image. Not sure I will
Mark, yes the script is set up for IN2 as the primary use for the IC-7000 was for HF. It has been a while since I used it for VHF with the DRAWS and I have not tried the latest image. Not sure I will
|
By
Corky Searls
· #5178
·
|
|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
Corky (AF4PM): Thanks for your reply. I did try combinations of turning 9600 on/off on the radio, along with setting pin 4(DESC) / pin 5(AF) in DRAWS manager, all with no detectable difference in deco
Corky (AF4PM): Thanks for your reply. I did try combinations of turning 9600 on/off on the radio, along with setting pin 4(DESC) / pin 5(AF) in DRAWS manager, all with no detectable difference in deco
|
By
Mark J Culross
· #5177
·
|
|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
Mark, a quick question regarding the IC-7000 config. Do you have this set for 1200 baud or 9K6? You will need to make sure that you are listening to the correct pin on the mini-din connector. I believ
Mark, a quick question regarding the IC-7000 config. Do you have this set for 1200 baud or 9K6? You will need to make sure that you are listening to the correct pin on the mini-din connector. I believ
|
By
Corky Searls
· #5176
·
|
|
DRAWS - not able to receive APRS
#aprs
#ax25
#direwolf
I finally found some time to play with my new DRAWS (attached to RPi3B+, running current image dated 2020-Aug-22), but I've run into a roadbock. To start, I followed <https://nw-digital-radio.groups.i
I finally found some time to play with my new DRAWS (attached to RPi3B+, running current image dated 2020-Aug-22), but I've run into a roadbock. To start, I followed <https://nw-digital-radio.groups.i
|
By
Mark J Culross
· #5175
·
Edited
|
|
#aprs
#aprs
Thanks Basil, I am on my way now: 12 17:13:53 EDT, host: asawizard, gps: Ok, bat: +0.00V Seq: 3 Location: 30°06.48' N 81°28.84' W - locator EM90GC25HW - show map - static map 7.3 miles Southwest beari
Thanks Basil, I am on my way now: 12 17:13:53 EDT, host: asawizard, gps: Ok, bat: +0.00V Seq: 3 Location: 30°06.48' N 81°28.84' W - locator EM90GC25HW - show map - static map 7.3 miles Southwest beari
|
By
Paul Noa
· #4732
·
|
|
#aprs
#aprs
btest.sh script defaults to sending a message 'btest.sh -p' sends a location beacon $ ./btest.sh -h *** Running as user: pi *** Usage: btest.sh [-P <port>][-s <num>][-p][-m][-v][-h] -P <portname> | --
btest.sh script defaults to sending a message 'btest.sh -p' sends a location beacon $ ./btest.sh -h *** Running as user: pi *** Usage: btest.sh [-P <port>][-s <num>][-p][-m][-v][-h] -P <portname> | --
|
By
Basil Gunn
· #4731
·
|
|
#aprs
#aprs
Thanks Everyone, My nearest ham friend sent me this he received on his home rig: KO4BCZ-11 audio level = 26(7/7) [NONE] |||||||__ [0.3] KO4BCZ-11>APUDR1,WIDE1-1::KO4BCZ :11 15:54:28 EDT KO4BCZ mesg_be
Thanks Everyone, My nearest ham friend sent me this he received on his home rig: KO4BCZ-11 audio level = 26(7/7) [NONE] |||||||__ [0.3] KO4BCZ-11>APUDR1,WIDE1-1::KO4BCZ :11 15:54:28 EDT KO4BCZ mesg_be
|
By
Paul Noa
· #4730
·
|