Hello Basil, that's great ... I did this (below my steps and results). It is essential to stop AX25 before. Now the switch between Fldigi and WSJTX is smooth. Great script and very helpful. My next st

#config #wsjtx #audio #install

Erwin: I have a kx2 and following is what I ran with an unmodified script. First run stop then start & status. Reboot & check status. Verify that your baud rate matches what is in your radio. Check th

#config #wsjtx #audio #install

Hello Basil, thank you very much for your support ... made the update - but problem is after changing the script to only use the KX3 I commented the other radios so only the KX3 line is active. declar

#config #wsjtx #audio #install

There is a new script wsjtx_ctrl.sh which will auto start rigctld-wsjtx with a systemd service file. readme: https://github.com/nwdigitalradio/n7nix/blob/master/hfprogs/README.md script: https://githu

#config #wsjtx #audio #install

Hi Basil, I did a fresh installation (#5710) but the Error on starting Hamlib (4.1) for Wsjtx ist still there. Result before I stopped pulse audio: pi@draws:~ $ rigctld-wsjtx -m 2029 -r /dev/ttyUSB0 -

#config #wsjtx #audio #install

Hi Basil, Thanks will combine this with my efforts to make an enhanced image for my needs (#5700). I described the error in #5690 - formated as it was in the terminal window. It is the problem, that I

#config #wsjtx #audio #install

Good, some success! Could you please post the error you are referring to. Yes I have had a few problems with pulseaudio since end of last year. I am currently ignoring those errors as I do not use pul

#config #wsjtx #audio #install

Hello Basil, JS8call works now ... it was only bad reception. But the error when putting presets for ham radio in the terminal before I start JS8call or WSJTx is already present. Bought my KX3 from a

#config #wsjtx #audio #install

Should not have to start it twice, symptom of a problem. Before you issue the rigctld-wsjtx command verify the cat control serial device (ttyUSB0) is present in /dev directory. ls /dev/ttyUSB* # Make

#config #wsjtx #audio #install

Hi Basil, thanks for the explanation! I got things working by starting the daemon. But I have to do this twice. First start results in an error, second is successful. Do you have an explanation fo thi

#config #wsjtx #audio #install

I need to change my doc as you need start the rigctl daemon first. Also you need to see what the baud rate (-s) is set to for on your KX3 rig control. -s Assuming the baud rate is 19200 bps. -m rig nu

#config #wsjtx #audio #install

Hi Basil, I digged a little more in the setup like you proposed. Problem is in wsjt-x. Can't save the settings I made according your proposal - it ends up with a Hamlib error. Of course the same in JS

#config #wsjtx #audio #install

Hi Erwin, All your console output looks good! I recently setup wsjt-x and js8call using a DRAWS card and have the following notes using HAMLib/rigctl. In the wsjt-x/js8call config I set my rig to 'Ham

#config #wsjtx #audio #install

Hi Basil, thanks for the hint. So it is a language problem :-) I changed the language on the raspberry pi from German to English to avoid future problems with tolls and language. Here is the output an

#config #wsjtx #audio #install

Erwin, The console output you posted looks OK. Except for this: which could be a locale problem as I parse out the sound card names from aplay -l. The parser is biased towards English (sorry) and is m

#config #wsjtx #audio #install

Hello, I use the Elecraft KX3 and installed the NW-image on my Pi4 and went straight forward the steps of the instructions. All run smooth but not the audio. Here are my checks: pi@raspberrypi:~ $ apl

#config #wsjtx #audio #install

Happy to hear that you have it working Jakob! aa0jr de n7nix

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

Thanks Basil, I get input and output signals! That means it is working now with fldigi. CAT with flrig. I will observe it and do the final finetuning. Thanks again and 73 de jakob, aa0jr

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

Good! The ALSA control values are incorrect. If you run the following script in a console that should get you close. setalsa-ft817.sh Is your radio a Yaesu FT-817 or an FT818? You mention both.

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x

Hi Basil, Now the NWDR image is up and running. I followed the WIKI instructions up to the fldigi installation and setup. When I arrived at the output gain adjustment with the fldigi Tune function, I

#ft-817 #audio #drawsmanager #draws-manager #wsjt-x