Did not know that. Usually the first time you edit one of the system files like a crontab entry you get presented with a menu of all the editor choices. I don't mess with any default system settings l

#beta #support

Thanks for the reply Basil. I am a real Newbie to DRAWS and Linux but I muddled through the install until I went to setup ARDOP from the web and then later discovered there was a script to do that. So

#beta #support

direwolf is a daemon & is controlled by systemd as is the preferred method for controlling daemons that usually start from boot. The scripts to start/stop/status direwolf & the ax.25 interface are: cd

#beta #support

I installed NWDR14. I have not spent much time with DRAWS and in fact have no radios hooked up right now (working on that). So this project has been "benchware" for me. I did bring up FLDigi and it lo

#beta #support

Thanks a million for the secondary download location, William. Pulled down a copy and just booted the Pi-3 / DRAWS to take a look and make sure I had followed the correct setup sequence. Looks like th

#beta #support

As a reminder. Basil puts together these images as a favor and courtesy to the community. NW Digital Radio is not the author of Linux/Raspbian or any of the applications that are preloaded on the beta

#beta #support

David C Jenner - K7DCJ via Groups.Io <djenner8=mac.com@groups.io> writes: Not sure why you would want to do this as the provided image has already done the heavy lifting of the install but if you real

#beta #support

Just downloaded this myself and it took a while so cloned it here: https://tor1.radiowaves.ca/nwdr14.zip This is a Digital Ocean virtual in Toronto, set the limit at 900GB so go nuts. It gave me 42MB/

#beta #support

Basil, I have a Raspbian Buster RPi 4 running the desired kernel. I want to install whatever is included in the standard DRAWS image over this. I suspect there is no file n7nix/config/image_install.sh

#beta #support

Dave, The "DRAWS specific software" are two codec drivers that are in the Linux kernel and an overlay that loads at boot time. The drivers are: snd_soc_tlv320aic32x4_i2c snd_soc_tlv320aic32x4 The over

#beta #support

Basil, Please add how to install this on one's own RPi 4 Raspbian image (with proper kernel). Your instructions at "Make your own Raspberry Pi image" seem to end before adding the DRAWS-specific softw

#beta #support

Before you update your image, please capture any configuration changes you might have made like current alsamixer settings. Run alsa-show.sh & make a copy of result. Note a minimum microSD card size o

#beta #support

file n7nix/debug/btest.sh hardcoded N and W current beacon_msg="!${lat}N/${lon}W-$timestamp, from $(hostname) on port $AX25PORT Seq: $seqnum" recommended beacon_msg="!${lat}${latdir}/${lon}${londir}-$

#beta

Hi Basil, Life got in the way of doing the patch you suggested last Friday, by the time I could look it over again, your instructions to run the following worked perfectly: cd cd bin ./prog_refresh.sh

#draws #beta #flrig

Hi Jack, libjpeg.so.9 should have been installed when fldigi was built. I need to figure out why that did not happen. I may have been too aggressive with cleaning up files after a build. In the mean t

#draws #beta #flrig

Basil, I started playing with fldigi - it configured properly and worked except... flrig fails with a blank stare.(hourglass... then nothing) in the X GUI When run from the console window see msg: err

#draws #beta #flrig

Yes, you will need to stop and start the daemon (or reboot) to pickup the new direwolf, if you have it running.. sudo systemctl stop direwolf sudo systemctl start direwolf

#setup #draws #beta #image

John D Hays - K7VE <john@hays.org> writes: And that will get you the "Device or resource busy" shown below because direwolf is started with systemd. So do NOT do that. I only support direwolf running

#setup #draws #beta #image

With this new direwolf executable, you can run direwolf -c /etc/direwolf.conf Assuming your direwolf.conf is in /etc -- within that file, setup your gpsd connection and beacons. Note: direwolf is auth

#setup #draws #beta #image

Here you are. And finally I’ve seen the missing two lines. pi@WoMoAPRSetc:~ $ gpsd -V gpsd: 3.18.1 (revision 3.18.1) pi@WoMoAPRSetc:~ $ cd /usr/local/src/direwolf-dev pi@WoMoAPRSetc:/usr/local/src/dir

#setup #draws #beta #image