Per owners manual of the TS-440 it should be 500mV or less. I’ve attached a screen shot of the only page that addresses input voltages for that connector.

#js8call #beta7 #din6 #kenwood #applications

Bryan & John - I just realized it would be much simpler for me to use the AFSK input and output RCA jacks to the TS-440s to verify the DRAWS card will be able to drive the transmitter before tearing i

#js8call #beta7 #din6 #kenwood #applications

Bryan & John - I have searched the Kenwood documentation and can't find a spec for the Data Input line on the 13 DIN connector. That said I have found a mod that changes where the Data Input ties into

#js8call #beta7 #din6 #kenwood #applications

Max Output from DRAWS is ~3.2V Peak to Peak Bryan

#js8call #beta7 #din6 #kenwood #applications

What is the spec for the PTP input voltage?

#js8call #beta7 #din6 #kenwood #applications

Team - The DRAWS TI DAC does not have enough audio output to drive the Kenwood TS-440S Data Input connection which is on pin 11 of the 13 pin DIN connector on the back of the radio. This is not a issu

#js8call #beta7 #din6 #kenwood #applications

echoing Mike's comments..NWD Keep up the great work

#earlyadopters #beta7

Ladies and Gentlemen of NW Digital Radio, I just want to the thank you for introducing the DRAWS Pi-Hat! I have greatly enjoyed working with the card and the beta software! Your tireless support is gr

#earlyadopters #beta7

Fellow DRAWs Early Adopters, I am happy to report I am making progress with getting the DRAWS card to work with the Kenwood TS-440S on HF digital modes. I have JS8Call & WSJT-X FT8 Mode decoding signa

#js8call #beta7 #din6 #kenwood #applications

Hi Tim, I have played with all of the suggestions you made and many others... I don’t run the 7000 on packet or in digi modes with the Mic connected... period. That is terrible practice with almost an

#beta7 #config #ft-817 #ic-7000

I don’t know if you have a way to measure the voltage coming out of DRAWS to compare Direwolf and Fldigi. I would suppose they would be the same. Have you tried adjusting the Mic gain? As odd as it ma

#beta7 #config #ft-817 #ic-7000

Thanks for sending that photo. I missed that in the packet section. So in my testing, that seems to be the case for packet on FM (APRS via direwolf) which has been working. Unfortunately when DRAWS TX

#beta7 #config #ft-817 #ic-7000

Hello Jack, Thank you and I hope this baby learns quickly that it’s hard to function when he doesn’t want to lay down in bed very long. I had hoped my photo showed the information about voltage you we

#beta7 #config #ft-817 #ic-7000

Hi Tim, To clarify one point from my rambling response to Basil, I just use the DATA port on the IC-7000 with DRAWS. What I was referring to was that the copy of the 7000 manual I have does not state

#beta7 #config #ft-817 #ic-7000

Hi Basil and Jack, Let me preface by saying that I am very interested in the progress you are making as I too have an IC-7000. I wish I had time to test but we just had a newborn arrive in December ke

#beta7 #config #ft-817 #ic-7000

Basil, Thanks again for your comments and special thanks ahead of time to John for doing that GUI menu. It will make a big difference during setup. I fear this post will get too long if I just comment

#beta7 #config #ft-817 #ic-7000

See embedded below. Jack Spitznagel <kd4iz@frawg.org> writes: John is working on a GUI config program This is not unexpected the FT-817 and any HF VHF/UHF radio has 2 distinct radios so would not expe

#beta7 #config #ft-817 #ic-7000

Following up......... I was able to download the file at work and successfully unzip it there. Weird error.

#beta7

Jack, Understood. Just not working for me at the moment. 73s, Ed, KD9FRQ

#beta7

Just noticed I got bit by my cut/paste haste! I used the setalsa-ic7000.sh script to initially set audio levels for that radio. All else is correct. Jack - KD4IZ

#beta7 #config #ft-817 #ic-7000