|
Another guy trying to set DRAWS Hat levels for an IC-7000 11 messages
#ic-7000
#draws
Russ, The configuration you are looking to implement is one that I have used, so I know that it does work. One thing that would help with testing would be to have two radios set up and operational. I
Russ, The configuration you are looking to implement is one that I have used, so I know that it does work. One thing that would help with testing would be to have two radios set up and operational. I
|
By
Corky
·
|
|
SSTV on DRAWS™ 7 messages
#draws
#sstv
#experimenter
Reviving this old thread. I have had success getting the latest version of QSSTV 9.5.3 working with my DRAWS Hat and the GPIO pins for PTT instead of CAT. I had to compile QSSTV from source and I've o
Reviving this old thread. I have had success getting the latest version of QSSTV 9.5.3 working with my DRAWS Hat and the GPIO pins for PTT instead of CAT. I had to compile QSSTV from source and I've o
|
By
Jim VA7SHG/VE7TGZ
·
|
|
Output of showurds.sh 2 messages
#draws
Donald, Thank you for the console output for showudrc.sh I am fairly certain this is showing a hardware failure. To confirm could you please run the following console commands and paste the console ou
Donald, Thank you for the console output for showudrc.sh I am fairly certain this is showing a hardware failure. To confirm could you please run the following console commands and paste the console ou
|
By
Basil Gunn
·
|
|
New to DRAWS - what order to troubleshoot installation/setup? 7 messages
#draws-manager
#ft-817
#ft817
#draws
#gps
Hi Basil, I'm back at it. So close. After pulling the #6 pin (and breaking the key off... oops), I can now see all sorts of APRS signals streaming in with: tail -f /var/log/direwolf/direwolf.log Howev
Hi Basil, I'm back at it. So close. After pulling the #6 pin (and breaking the key off... oops), I can now see all sorts of APRS signals streaming in with: tail -f /var/log/direwolf/direwolf.log Howev
|
By
Microbes
·
|
|
DRAWS™ Latest Board Run Defect (Standby) 25 messages
#recall
#draws
I'm thinking it's this thread: https://nw-digital-radio.groups.io/g/udrc/topic/68158957#4269 thanks for the heads up.
I'm thinking it's this thread: https://nw-digital-radio.groups.io/g/udrc/topic/68158957#4269 thanks for the heads up.
|
By
michael
·
|
|
#draws Receive audio through IC-880H now has added noise while DRAWS is connected to it ... 5 messages
#draws
An update on my post: I have been able to make the problem go away, the problem of “added noise to receive audio through the ID-880H” when the DRAWS card was connected to the radio. Not completely sur
An update on my post: I have been able to make the problem go away, the problem of “added noise to receive audio through the ID-880H” when the DRAWS card was connected to the radio. Not completely sur
|
By
Hoop K9QJS
·
|
|
DRAWS™ Boards Shipping 13 messages
#draws
I’ll post an update on the case situation later this week. Bryan K7UDR
I’ll post an update on the case situation later this week. Bryan K7UDR
|
By
Bryan Hoyer
·
|
|
Ran update.. now PI won't boot 13 messages
#draws
This is a common problem. Check if there is a script called chk_perm.sh in your local bin directory. /home/pi/bin Run that script. If you can not find the script then just. cd /usr/local/var sudo chow
This is a common problem. Check if there is a script called chk_perm.sh in your local bin directory. /home/pi/bin Run that script. If you can not find the script then just. cd /usr/local/var sudo chow
|
By
Basil Gunn
·
|
|
Shutdown-/reboot pushbutton 8 messages
#power
#draws
That's what it was John... I wasn't "joined" to the AMBE subgroup. Thanks & 73 de Mike
That's what it was John... I wasn't "joined" to the AMBE subgroup. Thanks & 73 de Mike
|
By
VE3MIC
·
|
|
Failure activating AX25, need help to fix 6 messages
#draws
#direwolf
#a25
Hi, any news regarding DRaws Hat + PiJuice Hat compatibility? thx
Hi, any news regarding DRaws Hat + PiJuice Hat compatibility? thx
|
By
Laurent Lathieyre | K2BRC
·
|
|
mheard not working. Help debugging? 5 messages
#draws
#ax25
Mheard is working now on my draws system. I had fixed the duplicate call sign in /etc/ax25/axports. However I had not rebooted. Alternatively I could have restarted ax25 service by running ax25-stop a
Mheard is working now on my draws system. I had fixed the duplicate call sign in /etc/ax25/axports. However I had not rebooted. Alternatively I could have restarted ax25 service by running ax25-stop a
|
By
Jay S
·
|
|
#DRAWS oddity, GPS and ALSA headaches 12 messages
#draws
Hi Basil, Well, I finally got a chance to do a "multiswap" to see what hardware is working and what is not with this DRAWS system. Previously determined that the GPS antenna we have discussed was bad
Hi Basil, Well, I finally got a chance to do a "multiswap" to see what hardware is working and what is not with this DRAWS system. Previously determined that the GPS antenna we have discussed was bad
|
By
Jack Spitznagel
·
|
|
Keying FreeDV with GPIO 2 messages
#draws
#freedv
I am bringing this topic back up...does anyone have a working FreeDV on DRAWS yet... I am just asking for completeness... Mike KF5DEY
I am bringing this topic back up...does anyone have a working FreeDV on DRAWS yet... I am just asking for completeness... Mike KF5DEY
|
By
Mike B
·
|
|
Update WSJTX 4 messages
#draws
#wsjt-x
Hello Basil. I went ahead and updated as you instruct in this thread. As I did this, this message came up: authentication required to restart 'dphys-swapfile.service multiple identities can be used fo
Hello Basil. I went ahead and updated as you instruct in this thread. As I did this, this message came up: authentication required to restart 'dphys-swapfile.service multiple identities can be used fo
|
By
TG9AOR
·
|
|
Setting Up AARDOP with the 8 messages
#draws
Two radios, but running packet & some HF program at the same time on your RPi. I run packet using my vhf/uhf radio & some HF program (FLdigi) on my HF rig. The way I use it is for convenience of leavi
Two radios, but running packet & some HF program at the same time on your RPi. I run packet using my vhf/uhf radio & some HF program (FLdigi) on my HF rig. The way I use it is for convenience of leavi
|
By
Basil Gunn
·
|
|
DummyRepeater for DRAWS
#dtarrepeater
#dummyrepeater
#draws
Hi All, So being in quarantine I have some extra time on my hands. I took on DummyRepeater and made it work with DRAWS. In the mean time I fixed some issues like resources not always being released or
Hi All, So being in quarantine I have some extra time on my hands. I took on DummyRepeater and made it work with DRAWS. In the mean time I fixed some issues like resources not always being released or
|
By
Geoffrey Merck
·
|
|
#draws
#draws
Basil, I edited axport file here is the current output from Showudrc showudrc.sh ==== Sound Card ==== udrc card number line: card 0: udrc [udrc], device 0: bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4
Basil, I edited axport file here is the current output from Showudrc showudrc.sh ==== Sound Card ==== udrc card number line: card 0: udrc [udrc], device 0: bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4
|
By
Paul Noa
·
|
|
No Transmit
#draws
I was reading Michael Sharp's messages where he also indicates no transmit. Perhaps I too have a bad board, Is there any way to identify the units with the issue? Serial #, specific parts etc? Other R
I was reading Michael Sharp's messages where he also indicates no transmit. Perhaps I too have a bad board, Is there any way to identify the units with the issue? Serial #, specific parts etc? Other R
|
By
Paul Noa
·
|
|
#draws
#draws
What could prevent transmitting with DRAWS Hat running NWDR15 on Pi3 B+ ? /home/pi/n7nix/debug# ./btest.sh -P udr0 Send a message beacon Sent: /usr/local/sbin/beacon -c KO4BCZ-11 -d 'APUDR1 via WIDE1-
What could prevent transmitting with DRAWS Hat running NWDR15 on Pi3 B+ ? /home/pi/n7nix/debug# ./btest.sh -P udr0 Send a message beacon Sent: /usr/local/sbin/beacon -c KO4BCZ-11 -d 'APUDR1 via WIDE1-
|
By
Paul Noa
·
|
|
DRAWS Setup ans Operational Manual? 3 messages
#draws
#setup
That would be VERY helpful.
That would be VERY helpful.
|
By
Bailey
·
|