Happy that your setup is working for you! Have some fun. /Basil n7nix TG9AOR <qrz@...> writes:

#wsjt-x #ft-8

Basil, thank you for your response. I cycled the PWR slider: no change. I cycled the Output device on my audio tab, from plughw:CARD=udrc,DEV=0 Mono to default, and to Left on the drop down list box n

#wsjt-x #ft-8

Looking at my notes to see what might be relevant because I do not own an FT-450. * Re: FT-817, I could only get this radio to work by disconnecting pin 6 (squelch) on the mDin6 cable. https://github.

#wsjt-x #ft-8

Hello Friends. I have this setup on WSJT-X that came with the DRAWS Image (WSJT-X v2.0.1 7ddcb7) Radio Tab Audio Tab Rig: FT-450 Input plughw:CARD=udrc,DEV=0 Mono Serial Port /dev/ttyUSB0 Output plugh

#wsjt-x #ft-8

Hello Tim, Sorry about the delay in my response, life took priority! I've set my width to 3000 Hz and noticed no difference in my ability to send FT8 transmissions between the DRAWS and my radio. The

#ft-891 #draws #ft-8 #wsjtx

Matt, Also make sure your width is set to 3000Hz I notice on your radio it says LAP on the screen, upper left Do you have an amp connected? Maybe try the radio without a tuner or amp connected. Tim /

#ft-891 #draws #ft-8 #wsjtx

Forgot to include my DRAWS manager screenshot! Cheers, Matt - N7ROO

#ft-891 #draws #ft-8 #wsjtx

Thanks for the response Tim. I tried resetting my radio and also reflashed the DRAWS image. I've confirmed that I have the same menu settings as you, and that I'm using the left channel. I've included

#ft-891 #draws #ft-8 #wsjtx

Thanks for the confirmation Jim and John. I think I will get the 3B+ as I run completely off of solar power and the 3B+ will use less power than the 4. 73 N1ESE

#ft-8 #draws #wsjt-x

DRAWS™ is decoding FT8 and other signals just fine on the Raspberry Pi 3 (B/B+) without even challenging CPU utilization. If other groups are reporting problems, it may have more to do with the hardwa

#ft-8 #draws #wsjt-x

They all work fine on my Pi 3B+. I also just did a ./prog_refresh.sh this morning and got the latest WSJT-X 2.1 installed. Haven’t tried decoding FT-8 with the latest version, but has worked fine for

#ft-8 #draws #wsjt-x

Does the Pi 3B+ decode FT8 properly or should I wait on the Pi 4 for the faster CPU? I'm getting mixed reports from other Raspberry groups. I already have a DRAWS and just waiting to see how the Pi 4

#ft-8 #draws #wsjt-x

Matt, You may want to reset the radio. I have done that in the past when problems arise. I use the included menu settings after I reset the radio. I am using the left audio channel. Have you checked t

#ft-891 #draws #ft-8 #wsjtx

Thanks all for your suggestions. I've made sure that my "DATA IN SELECT" (setting 08-09) is set to "REAR" rather than "MIC", and confirmed this by whistling into my mic while transmitting. No transmis

#ft-891 #draws #ft-8 #wsjtx

Be aware that the 2.1.0 rc7 version does not now transmit data on my Mac. Apparently has some built-in switch to turn it off during some periods. Version 2.0.1 does work on the Mac and the 3B+ under S

#ft-891 #draws #ft-8 #wsjtx

Have you looked at the output settings in draws manager and tried to adjust those? Have you confirmed that the audio settings are correct for transmit in the wsjt-x program? Lastly, have you adjusted

#ft-891 #draws #ft-8 #wsjtx

Hi Matt. Make sure the radio is getting the input from the 6-pin data port. I don't have a FT-891, but look into mode. Could be called USB-D, DIG or similar. I've had similar problems were other radio

#ft-891 #draws #ft-8 #wsjtx

Hello, I've been trying to set up my DRAWS and FT-891 to use FT8 via WSJT-X. I've been following the videos and settings from Julian and Steve, and can receive messages ok, however whenever I transmit

#ft-891 #draws #ft-8 #wsjtx

https://www.youtube.com/watch?v=ZIFeSoC19_A

#ft-817 #draws #ft-8 #ft817 #hf