Basil, Yes, I using Release 15 or 16 and the DRAWS. It is working great for email and APRS (this was my main goal). I am still collecting the gear needed to put it all in Gator box to go yet still use

Basil, Thank you for your reply. I have CLAWS working on my Pi / DRAWS setup. How much trouble would it be to get MUTT working in parallel? Just curious. Ed Bloom, KD9FRQ ewbloom@... Sent from

Mitch, Yes, it would. I asked here just in case anyone has done with the DRAWS and the underlying OS image. I also asked here because the DRAWS developers may know the answer based on their knowledge

The Pi has Bluetooth and WiFi. Is there a way to have PAT send a notification that "I've Got Mail" if there is a new message received via wl2kax25 command? 73s, Ed, KD9FRQ

Basil, Thank you. It works as stated. 73s, Ed, KD9FRQ

Basil, Thank you for the beacon script offer. I accept. I would like to beacon "KD9FRQ on air and monitoring" 73, Ed, KD9FRQ

Is Pac-Link always able to receive a message via a Peer-to-Peer connection like the PC-based WinLink when it is set in Peer-to-Peer mode? If I am not xmitting how do others know I am on line and able

Thank you. I edited the file to make the email address correct per your note. That corrected to problem.T

Following the Readme, everything seems to be in order. Claws sends out to pi@localhost and whereever the wl2kax25 program needs to have outbox data. It seems the script ran fine but defaulted to telne

Since I finally got a second antenna up and the second 2m rig, I now have my DRAWS running APRS on udr0 and wl2kax25 sending and receiving on udr1. Claws Mail is properly sending mail out and wl2kax25

Thank you, Basil, Does the /usr/local/etc/wl2k.conf need to stay as udr0 or can I change it since I am wanting to use udr1 for EMAIL and leave urd0 for APRS as the frequesncies are different? Ed, KD9F

#wl2kax25

I am now ready to move forward with sending email via wl2kax25. I just connected my second 2m rig to Port1. Port0 is currently running XASTIR as a gateway. I am not getting the -a PORT part of the com

#wl2kax25

I am looking for some more formalized End-User Directions to keep on the thumb drive, and print for the Go Bag/Box. What I am looking for is how to swap ports from 0 to 1 should the port 0 fail on the

Thank you. During my WFH lunch hour, I was able to successfully use that method and copy the SD card that was used to boot the Pi. I swapped the cards and the Pi booted as expected. Now...…………..to get

Follow up question................. Now that I have a stable config with NWDR-15 : How do I use a USB micro SD Card device to replicate the entire active SD card? Ed, KD9FRQ

Thank you, Basil. I have it working now and can receive APRS. Ed, KD9FRQ

I got NQDR15 to load and configured so that it returns all the values noted in the Wiki (Confirm Install). YAAC icon worked and let me start setting up. Xastir icon just "sits there" after double clic

Basil, Restated and named my system something new. All the basic checks now seem to work. And I get local email back, AX25 Start and Stop desktop icon works. YAAC icon works and started me on the path

Where can I find the PLU and Xastir setup and use instructions for our DRAWS? Xastir will start and I have entered the basic information. Now, how do I get it to see the DRAWS and start receiving? Sam

My shack in the basement. I only have two, 16x28 windows. Both have very, very limited view of sky. What GPS extender do you recommend and why? Or could I put an SMA bulkhead connector through the wal