Topics

DRAWS not found


Keating Floyd
 

Hi, all.

Included is the output from showudrc.sh.  I was concerned that I had a problem with my image perhaps, but I own a second DRAWS, and it shows up just fine.

Thanks for a great product, and for your help.

Keating

===

root@pi4b4g01:/home/pi/n7nix/hfprogs# cat showudrc.sh_out 
==== Sound Card ====
No udrc sound card found.
==== Pi Ver ====
 Pi 4 Model B, Rev 1.1, 4GB mem, Mfg by Sony UK
 Has WiFi
==== udrc Ver ====
Found a DRAWS
 
     HAT ID EEPROM
Name:        hat
Product:     Digital Radio Amateur Work Station
Product ID:  0x0004
Product ver: 0x0204
UUID:        7499df1d-8bc8-401d-b978-97518d36967e
Vendor:      NW Digital Radio
 
==== sys Ver ====
----- image version
2020 06 08 11:50:00 PDT: SD image version: nwdr16
----- /proc/version
Linux version 4.19.118-v7l+ (dom@buildbot) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1311 SMP Mon Apr 27 14:26:42 BST 2020
 
----- /etc/*version: 10.4
 
----- /etc/*release
PRETTY_NAME="Raspbian GNU/Linux 10 (buster)"
NAME="Raspbian GNU/Linux"
VERSION_ID="10"
VERSION="10 (buster)"
VERSION_CODENAME=buster
ID=raspbian
ID_LIKE=debian
HOME_URL="http://www.raspbian.org/"
SUPPORT_URL="http://www.raspbian.org/RaspbianForums"
BUG_REPORT_URL="http://www.raspbian.org/RaspbianBugs"
 
----- lsb_release
Distributor ID: Raspbian
Description: Raspbian GNU/Linux 10 (buster)
Release: 10
Codename: buster
 
---- systemd
   Static hostname: pi4b4g01
         Icon name: computer
        Machine ID: 27ac1f0c20904cb7a960920e966db545
           Boot ID: a5894491276b45ce98a950a72d323b2c
  Operating System: Raspbian GNU/Linux 10 (buster)
            Kernel: Linux 4.19.118-v7l+
      Architecture: arm
 
---- modules
 
---- kernel
|/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad)
||/ Name               Version      Architecture Description
+++-==================-============-============-=================================
ii  raspberrypi-kernel 1.20200601-1 armhf        Raspberry Pi bootloader
 
---- Codec drivers
Found: snd-soc-tlv320aic32x4-i2c.ko, OK
Found: snd-soc-tlv320aic32x4.ko, OK
 
Directory: /proc/device-tree/soc/i2c@7e804000/tlv320aic32x4@18 does NOT exist
 
Directory: /proc/device-tree/soc/i2c@7e804000 exists and status is disabled
 
---- syslog
 
---- dmesg
 
 
----- Dire Wolf DEVELOPMENT version 1.6 E (May 11 2020)
 
==== Filesystem ====
/dev/root        29G  5.0G   23G  19% /
 
==== boot config ====
 
[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
dtoverlay=vc4-fkms-v3d
 
[all]
#dtoverlay=vc4-fkms-v3d
 
# Flush all overlays, ie. deprecated overlays loaded from eeprom
dtoverlay=
# enable udrc/draws if no eeprom
dtoverlay=draws,alsaname=udrc
force_turbo=1
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
 
---- gpsd
/usr/local/sbin/gpsd
gpsd: 3.20 (revision 3.20)
● gpsd.service - GPS (Global Positioning System) Daemon
   Loaded: loaded (/lib/systemd/system/gpsd.service; enabled; vendor preset: enabled)
   Active: active (running) since Tue 2020-07-28 20:23:18 EDT; 11min ago
  Process: 545 ExecStart=/usr/local/sbin/gpsd $GPSD_OPTIONS $OPTIONS $DEVICES (code=exited, status=0/SUCCESS)
 Main PID: 552 (gpsd)
    Tasks: 1 (limit: 4915)
   Memory: 1.1M
   CGroup: /system.slice/gpsd.service
           └─552 /usr/local/sbin/gpsd -n /dev/ttySC0 /dev/pps0
 
Jul 28 20:23:18 pi4b4g01 systemd[1]: Starting GPS (Global Positioning System) Daemon...
Jul 28 20:23:18 pi4b4g01 systemd[1]: Started GPS (Global Positioning System) Daemon.
Jul 28 20:23:18 pi4b4g01 gpsd[552]: gpsd:ERROR: SER: device open of /dev/ttySC0 failed: No such file or directory - retrying read-only
Jul 28 20:23:18 pi4b4g01 gpsd[552]: gpsd:ERROR: SER: read-only device open of /dev/ttySC0 failed: No such file or directory
Jul 28 20:23:18 pi4b4g01 gpsd[552]: gpsd:ERROR: initial GPS device /dev/ttySC0 open failed
Jul 28 20:23:18 pi4b4g01 gpsd[552]: gpsd:ERROR: SER: device open of /dev/pps0 failed: No such file or directory - retrying read-only
Jul 28 20:23:18 pi4b4g01 gpsd[552]: gpsd:ERROR: SER: read-only device open of /dev/pps0 failed: No such file or directory
Jul 28 20:23:18 pi4b4g01 gpsd[552]: gpsd:ERROR: initial GPS device /dev/pps0 open failed
 
---- chrony
-- chrony sources
210 Number of sources = 6
MS Name/IP address         Stratum Poll Reach LastRx Last sample               
===============================================================================
#? GPS                           0   3     0     -     +0ns[   +0ns] +/-    0ns
#? PPS                           0   3     0     -     +0ns[   +0ns] +/-    0ns
^+ 12.167.151.1                  3   6   377     3  +4222us[+5787us] +/-   84ms
^+ white.web-ster.com            2   6   377     2   +391us[+1955us] +/-   83ms
^+ propjet.latt.net              3   6   137    62   -863us[ +702us] +/-   80ms
^* darwin.kenyonralph.com        3   6   377     1   -576us[ +988us] +/-   40ms
-- chrony tracking
Reference ID    : ADFFD7D1 (darwin.kenyonralph.com)
Stratum         : 4
Ref time (UTC)  : Wed Jul 29 00:34:41 2020
System time     : 0.001551948 seconds fast of NTP time
Last offset     : +0.001564196 seconds
RMS offset      : 0.002272248 seconds
Frequency       : 17.748 ppm fast
Residual freq   : -0.755 ppm
Skew            : 0.606 ppm
Root delay      : 0.077438146 seconds
Root dispersion : 0.001088197 seconds
Update interval : 64.6 seconds
Leap status     : Normal
-- chrony sourcestats
210 Number of sources = 6
Name/IP Address            NP  NR  Span  Frequency  Freq Skew  Offset  Std Dev
==============================================================================
GPS                         0   0     0     +0.000   2000.000     +0ns  4000ms
PPS                         0   0     0     +0.000   2000.000     +0ns  4000ms
12.167.151.1                8   6   264     -6.991     32.712  +3768us  1367us
white.web-ster.com          8   6   265     +0.924     12.906   +272us   601us
propjet.latt.net            7   4   205     +1.758     46.233  -1055us  1453us
darwin.kenyonralph.com      8   5   266     -1.417     10.676  -1406us   463us
 
---- sensors
-rw-r--r-- 1 root root 171 Sep 19  2019 /etc/sensors.d/draws
rpi_volt-isa-0000
Adapter: ISA adapter
in0:              N/A  
 
 
---- throttle
temp=51.0'C
throttled=0x0
 
---- locale
Locale country codes consistent among WiFi cfg file, iw reg & X11: US
core_config.sh has been run 0 time(s)
 


Basil Gunn
 

Keating,
I am looking into your problem.
Could you please tell me if you have anything plugged into the USB
ports on your RPi 4.
Thanks,
/Basil

Keating Floyd <kc4hsi@...> writes:

Included is the output from showudrc.sh. I was concerned that I had a problem with my image perhaps, but I own a second DRAWS, and it shows up just fine.

Thanks for a great product, and for your help.

Keating

===

root@pi4b4g01:/home/pi/n7nix/hfprogs# cat showudrc.sh_out
==== Sound Card ====
No udrc sound card found.
==== Pi Ver ====
Pi 4 Model B, Rev 1.1, 4GB mem, Mfg by Sony UK
Has WiFi
==== udrc Ver ====
Found a DRAWS

HAT ID EEPROM
Name: hat
Product: Digital Radio Amateur Work Station
Product ID: 0x0004
Product ver: 0x0204


Keating Floyd
 

Hi, Basil, and thanks!

Yes, I have a wireless keyboard dongle plugged in there.

Keating


On Tue, Jul 28, 2020, 9:36 PM Basil Gunn <basil@...> wrote:

Keating,
I am looking into your problem.
Could you please tell me if you have anything plugged into the USB
ports on your RPi 4.
Thanks,
/Basil

Keating Floyd <kc4hsi@...> writes:

> Included is the output from showudrc.sh. I was concerned that I had a problem with my image perhaps, but I own a second DRAWS, and it shows up just fine.
>
> Thanks for a great product, and for your help.
>
> Keating
>
> ===
>
> root@pi4b4g01:/home/pi/n7nix/hfprogs# cat showudrc.sh_out
> ==== Sound Card ====
> No udrc sound card found.
> ==== Pi Ver ====
> Pi 4 Model B, Rev 1.1, 4GB mem, Mfg by Sony UK
> Has WiFi
> ==== udrc Ver ====
> Found a DRAWS
>
> HAT ID EEPROM
> Name:    hat
> Product:  Digital Radio Amateur Work Station
> Product ID: 0x0004
> Product ver: 0x0204




Basil Gunn
 

Keating,

Using the same Raspberry Pi version & DRAWS hat version as you I booted
a fresh NWDR16 image and could not replicate your symptom.

The first thing to do after booting a new image is to run
aplay -l
which will tell you if the driver and overlays have loaded properly.
This is described in the Getting Started Guide
https://nw-digital-radio.groups.io/g/udrc/wiki/8921

What where the steps you took after your first boot of a new image?
ie. did you run apt-get update, or raspi-config, or pi-wiz setup?

I would like you to try and replicate what I did which is to burn the
image, boot & run aplay -l so that we can figure out what is causing
your problem.

$ udrcver.sh
Found a DRAWS

HAT ID EEPROM
Name: hat
Product: Digital Radio Amateur Work Station
Product ID: 0x0004
Product ver: 0x0204
UUID: 4a0b1dce-358e-4b50-a372-1118a9ecbfed
Vendor: NW Digital Radio

pi@raspberrypi:~ $ piver.sh
Pi 4 Model B, Rev 1.1, 4GB mem, Mfg by Sony UK
Has WiFi

pi@raspberrypi:~ $ aplay -l | grep udrc
card 2: udrc [udrc], device 0: bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4-hifi-0 [bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4-hifi-0]

/Basil n7nix

Keating Floyd <kc4hsi@...> writes:

Hi, Basil, and thanks!

Yes, I have a wireless keyboard dongle plugged in there.

Keating


On Tue, Jul 28, 2020, 9:36 PM Basil Gunn <@basil860> wrote:


Keating,
I am looking into your problem.
Could you please tell me if you have anything plugged into the USB
ports on your RPi 4.
Thanks,
/Basil

Keating Floyd <kc4hsi@...> writes:

Included is the output from showudrc.sh. I was concerned that I had a
problem with my image perhaps, but I own a second DRAWS, and it shows up
just fine.

Thanks for a great product, and for your help.

Keating

===

root@pi4b4g01:/home/pi/n7nix/hfprogs# cat showudrc.sh_out
==== Sound Card ====
No udrc sound card found.
==== Pi Ver ====
Pi 4 Model B, Rev 1.1, 4GB mem, Mfg by Sony UK
Has WiFi
==== udrc Ver ====
Found a DRAWS

HAT ID EEPROM
Name: hat
Product: Digital Radio Amateur Work Station
Product ID: 0x0004
Product ver: 0x0204


Keating Floyd
 

I believe I was following the getting started guide - but it is possible I did an upgrade first.  I will do exactly as you suggest!

Keating

On Wed, Jul 29, 2020 at 11:40 AM Basil Gunn <basil@...> wrote:
Keating,

Using the same Raspberry Pi version & DRAWS hat version as you I booted
a fresh NWDR16 image and could not replicate your symptom.

The first thing to do after booting a new image is to run
aplay -l
which will tell you if the driver and overlays have loaded properly.
This is described in the Getting Started Guide
https://nw-digital-radio.groups.io/g/udrc/wiki/8921

What where the steps you took after your first boot of a new image?
ie. did you run apt-get update, or raspi-config, or pi-wiz setup?

I would like you to try and replicate what I did which is to burn the
image, boot & run aplay -l so that we can figure out what is causing
your problem.

 $ udrcver.sh
Found a DRAWS

     HAT ID EEPROM
Name:        hat
Product:     Digital Radio Amateur Work Station
Product ID:  0x0004
Product ver: 0x0204
UUID:        4a0b1dce-358e-4b50-a372-1118a9ecbfed
Vendor:      NW Digital Radio

pi@raspberrypi:~ $ piver.sh
 Pi 4 Model B, Rev 1.1, 4GB mem, Mfg by Sony UK
 Has WiFi

pi@raspberrypi:~ $ aplay -l | grep udrc
card 2: udrc [udrc], device 0: bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4-hifi-0 [bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4-hifi-0]

/Basil n7nix

Keating Floyd <kc4hsi@...> writes:

> Hi, Basil, and thanks!
>
> Yes, I have a wireless keyboard dongle plugged in there.
>
> Keating
>
>
> On Tue, Jul 28, 2020, 9:36 PM Basil Gunn <basil@...> wrote:
>
>>
>> Keating,
>> I am looking into your problem.
>> Could you please tell me if you have anything plugged into the USB
>> ports on your RPi 4.
>> Thanks,
>> /Basil
>>
>> Keating Floyd <kc4hsi@...> writes:
>>
>> > Included is the output from showudrc.sh. I was concerned that I had a
>> problem with my image perhaps, but I own a second DRAWS, and it shows up
>> just fine.
>> >
>> > Thanks for a great product, and for your help.
>> >
>> > Keating
>> >
>> > ===
>> >
>> > root@pi4b4g01:/home/pi/n7nix/hfprogs# cat showudrc.sh_out
>> > ==== Sound Card ====
>> > No udrc sound card found.
>> > ==== Pi Ver ====
>> > Pi 4 Model B, Rev 1.1, 4GB mem, Mfg by Sony UK
>> > Has WiFi
>> > ==== udrc Ver ====
>> > Found a DRAWS
>> >
>> > HAT ID EEPROM
>> > Name:    hat
>> > Product:  Digital Radio Amateur Work Station
>> > Product ID: 0x0004
>> > Product ver: 0x0204




Keating Floyd
 

Hi,  Basil (et al).

I did as you suggested, and did not even do the "Welcome to the Raspberry Pi Desktop" setup.

aplay -l reports "aplay: device_list:272: no soundcards found..."

udrcver.sh reports:

     HAT ID EEPROM
Name:       hat
Product:    Digital Radio Amateur Work Station
Product ID: 0x0004
Product ver: 0x0204
UUID: 7499df1d-8bc8-401d-b978-97518d36967e
Vendor: NW Digital Radio

Thanks,

Keating

On Wed, Jul 29, 2020 at 1:03 PM Keating Floyd via groups.io <kc4hsi=gmail.com@groups.io> wrote:
I believe I was following the getting started guide - but it is possible I did an upgrade first.  I will do exactly as you suggest!

Keating

On Wed, Jul 29, 2020 at 11:40 AM Basil Gunn <basil@...> wrote:
Keating,

Using the same Raspberry Pi version & DRAWS hat version as you I booted
a fresh NWDR16 image and could not replicate your symptom.

The first thing to do after booting a new image is to run
aplay -l
which will tell you if the driver and overlays have loaded properly.
This is described in the Getting Started Guide
https://nw-digital-radio.groups.io/g/udrc/wiki/8921

What where the steps you took after your first boot of a new image?
ie. did you run apt-get update, or raspi-config, or pi-wiz setup?

I would like you to try and replicate what I did which is to burn the
image, boot & run aplay -l so that we can figure out what is causing
your problem.

 $ udrcver.sh
Found a DRAWS

     HAT ID EEPROM
Name:        hat
Product:     Digital Radio Amateur Work Station
Product ID:  0x0004
Product ver: 0x0204
UUID:        4a0b1dce-358e-4b50-a372-1118a9ecbfed
Vendor:      NW Digital Radio

pi@raspberrypi:~ $ piver.sh
 Pi 4 Model B, Rev 1.1, 4GB mem, Mfg by Sony UK
 Has WiFi

pi@raspberrypi:~ $ aplay -l | grep udrc
card 2: udrc [udrc], device 0: bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4-hifi-0 [bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4-hifi-0]

/Basil n7nix

Keating Floyd <kc4hsi@...> writes:

> Hi, Basil, and thanks!
>
> Yes, I have a wireless keyboard dongle plugged in there.
>
> Keating
>
>
> On Tue, Jul 28, 2020, 9:36 PM Basil Gunn <basil@...> wrote:
>
>>
>> Keating,
>> I am looking into your problem.
>> Could you please tell me if you have anything plugged into the USB
>> ports on your RPi 4.
>> Thanks,
>> /Basil
>>
>> Keating Floyd <kc4hsi@...> writes:
>>
>> > Included is the output from showudrc.sh. I was concerned that I had a
>> problem with my image perhaps, but I own a second DRAWS, and it shows up
>> just fine.
>> >
>> > Thanks for a great product, and for your help.
>> >
>> > Keating
>> >
>> > ===
>> >
>> > root@pi4b4g01:/home/pi/n7nix/hfprogs# cat showudrc.sh_out
>> > ==== Sound Card ====
>> > No udrc sound card found.
>> > ==== Pi Ver ====
>> > Pi 4 Model B, Rev 1.1, 4GB mem, Mfg by Sony UK
>> > Has WiFi
>> > ==== udrc Ver ====
>> > Found a DRAWS
>> >
>> > HAT ID EEPROM
>> > Name:    hat
>> > Product:  Digital Radio Amateur Work Station
>> > Product ID: 0x0004
>> > Product ver: 0x0204




Basil Gunn
 

Keating,
Sorry for the delay.

In a previous post you mentioned that you have a second DRAWS hat.

I was concerned that I had a problem with my image perhaps, but I own
a second DRAWS, and it shows up just fine.
Just to confirm are you saying that using the same mSD card that one
DRAWS hat is enumerated & another is not?

It sounds like you have a hardware problem.
Could you please send me the output of showudrc.sh on the working DRAWS
hat using the same mSD card used on the non-working DRAWS hat.

I already have the showudrc.sh output of the DRAWS hat that is not
enumerating. I would like to compare the outputs.

Thanks,
/Basil



Keating Floyd <kc4hsi@...> writes:

Hi, Basil (et al).

I did as you suggested, and did not even do the "Welcome to the Raspberry
Pi Desktop" setup.

aplay -l reports "aplay: device_list:272: no soundcards found..."

udrcver.sh reports:

HAT ID EEPROM
Name: hat
Product: Digital Radio Amateur Work Station
Product ID: 0x0004
Product ver: 0x0204
UUID: 7499df1d-8bc8-401d-b978-97518d36967e
Vendor: NW Digital Radio

Thanks,

Keating

On Wed, Jul 29, 2020 at 1:03 PM Keating Floyd via groups.io <kc4hsi=
gmail.com@groups.io> wrote:

I believe I was following the getting started guide - but it is possible I
did an upgrade first. I will do exactly as you suggest!

Keating

On Wed, Jul 29, 2020 at 11:40 AM Basil Gunn <@basil860> wrote:

Keating,

Using the same Raspberry Pi version & DRAWS hat version as you I booted
a fresh NWDR16 image and could not replicate your symptom.

The first thing to do after booting a new image is to run
aplay -l
which will tell you if the driver and overlays have loaded properly.
This is described in the Getting Started Guide
https://nw-digital-radio.groups.io/g/udrc/wiki/8921

What where the steps you took after your first boot of a new image?
ie. did you run apt-get update, or raspi-config, or pi-wiz setup?

I would like you to try and replicate what I did which is to burn the
image, boot & run aplay -l so that we can figure out what is causing
your problem.

$ udrcver.sh
Found a DRAWS

HAT ID EEPROM
Name: hat
Product: Digital Radio Amateur Work Station
Product ID: 0x0004
Product ver: 0x0204
UUID: 4a0b1dce-358e-4b50-a372-1118a9ecbfed
Vendor: NW Digital Radio

pi@raspberrypi:~ $ piver.sh
Pi 4 Model B, Rev 1.1, 4GB mem, Mfg by Sony UK
Has WiFi

pi@raspberrypi:~ $ aplay -l | grep udrc
card 2: udrc [udrc], device 0: bcm2835-i2s-tlv320aic32x4-hifi
tlv320aic32x4-hifi-0 [bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4-hifi-0]

/Basil n7nix

Keating Floyd <kc4hsi@...> writes:

Hi, Basil, and thanks!

Yes, I have a wireless keyboard dongle plugged in there.

Keating


On Tue, Jul 28, 2020, 9:36 PM Basil Gunn <@basil860> wrote:


Keating,
I am looking into your problem.
Could you please tell me if you have anything plugged into the USB
ports on your RPi 4.
Thanks,
/Basil

Keating Floyd <kc4hsi@...> writes:

Included is the output from showudrc.sh. I was concerned that I had a
problem with my image perhaps, but I own a second DRAWS, and it shows
up
just fine.

Thanks for a great product, and for your help.

Keating

===

root@pi4b4g01:/home/pi/n7nix/hfprogs# cat showudrc.sh_out
==== Sound Card ====
No udrc sound card found.
==== Pi Ver ====
Pi 4 Model B, Rev 1.1, 4GB mem, Mfg by Sony UK
Has WiFi
==== udrc Ver ====
Found a DRAWS

HAT ID EEPROM
Name: hat
Product: Digital Radio Amateur Work Station
Product ID: 0x0004
Product ver: 0x0204



Keating Floyd
 

Hi, Basil.  

Here is the output, using the other DRAWS hat.

===
==== Sound Card ====
udrc card number line: card 2: udrc [udrc], device 0: bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4-hifi-0 [bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4-hifi-0]
udrc is sound card #2
==== ALSA Controls for Radio Tansmit ====
LO Driver Gain  L:[0.00dB] R:[0.00dB]
PCM        L:[-20.00dB] R:[-20.00dB]
DAC Playback PT L:[P3] R:[P3]
LO Playback CM [Full Chip]
==== ALSA Controls for Radio Receive ====
ADC Level L:[0.00dB] R:[0.00dB]
IN1 L:[Off] R:[Off]
IN2 L:[Off] R:[Off]
==== Pi Ver ====
 Pi 4 Model B, Rev 1.1, 4GB mem, Mfg by Sony UK
 Has WiFi
==== udrc Ver ====
Found a DRAWS

     HAT ID EEPROM
Name:        hat
Product:     Digital Radio Amateur Work Station
Product ID:  0x0004
Product ver: 0x0405
UUID:        a922f489-2ab7-4c32-884f-deb7e2e06c40
Vendor:      NW Digital Radio

==== sys Ver ====
----- image version
2020 06 08 11:50:00 PDT: SD image version: nwdr16
----- /proc/version
Linux version 4.19.118-v7l+ (dom@buildbot) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1311 SMP Mon Apr 27 14:26:42 BST 2020

----- /etc/*version: 10.4

----- /etc/*release
PRETTY_NAME="Raspbian GNU/Linux 10 (buster)"
NAME="Raspbian GNU/Linux"
VERSION_ID="10"
VERSION="10 (buster)"
VERSION_CODENAME=buster
ID=raspbian
ID_LIKE=debian
HOME_URL="http://www.raspbian.org/"
SUPPORT_URL="http://www.raspbian.org/RaspbianForums"
BUG_REPORT_URL="http://www.raspbian.org/RaspbianBugs"

----- lsb_release
Distributor ID: Raspbian
Description: Raspbian GNU/Linux 10 (buster)
Release: 10
Codename: buster

---- systemd
   Static hostname: raspberrypi
         Icon name: computer
        Machine ID: 27ac1f0c20904cb7a960920e966db545
           Boot ID: 7830f48d368a43408457978c1ff66d11
  Operating System: Raspbian GNU/Linux 10 (buster)
            Kernel: Linux 4.19.118-v7l+
      Architecture: arm

---- modules
snd_soc_tlv320aic32x4_i2c    16384  9
snd_soc_tlv320aic32x4    40960  1 snd_soc_tlv320aic32x4_i2c
snd_soc_core          192512  5 vc4,snd_soc_simple_card_utils,snd_soc_bcm2835_i2s,snd_soc_tlv320aic32x4,snd_soc_simple_card
snd_pcm               102400  6 vc4,snd_pcm_dmaengine,snd_soc_bcm2835_i2s,snd_soc_tlv320aic32x4,snd_bcm2835,snd_soc_core
snd                    73728  14 snd_compress,snd_timer,snd_soc_tlv320aic32x4,snd_bcm2835,snd_soc_core,snd_pcm

---- kernel
|/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad)
||/ Name               Version      Architecture Description
+++-==================-============-============-=================================
ii  raspberrypi-kernel 1.20200601-1 armhf        Raspberry Pi bootloader

---- Codec drivers
Found: snd-soc-tlv320aic32x4-i2c.ko, OK
Found: snd-soc-tlv320aic32x4.ko, OK
Directory: /proc/device-tree/soc/i2c@7e804000/tlv320aic32x4@18 exists and status is okay

---- syslog

---- dmesg


----- Dire Wolf DEVELOPMENT version 1.6 E (May 11 2020)

==== Filesystem ====
/dev/root        29G  5.0G   23G  19% /

==== boot config ====

[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
dtoverlay=vc4-fkms-v3d

[all]
#dtoverlay=vc4-fkms-v3d

# Flush all overlays, ie. deprecated overlays loaded from eeprom
dtoverlay=
# enable udrc/draws if no eeprom
dtoverlay=draws,alsaname=udrc
force_turbo=1
# Enable audio (loads snd_bcm2835)
dtparam=audio=on

---- gpsd
/usr/local/sbin/gpsd
gpsd: 3.20 (revision 3.20)
● gpsd.service - GPS (Global Positioning System) Daemon
   Loaded: loaded (/lib/systemd/system/gpsd.service; enabled; vendor preset: enabled)
   Active: active (running) since Tue 2020-06-09 09:48:30 PDT; 14h ago
  Process: 689 ExecStart=/usr/local/sbin/gpsd $GPSD_OPTIONS $OPTIONS $DEVICES (code=exited, status=0/SUCCESS)
 Main PID: 695 (gpsd)
    Tasks: 3 (limit: 4915)
   Memory: 1.8M
   CGroup: /system.slice/gpsd.service
           └─695 /usr/local/sbin/gpsd -n /dev/ttySC0 /dev/pps0

Jun 09 09:48:30 raspberrypi systemd[1]: Starting GPS (Global Positioning System) Daemon...
Jun 09 09:48:30 raspberrypi systemd[1]: Started GPS (Global Positioning System) Daemon.

---- chrony
crw-rw---- 1 root root    241, 0 Jun  9 09:48 /dev/pps0
crw------- 1 root root    241, 1 Jun  9 09:48 /dev/pps1
crw-rw---- 1 root dialout 235, 0 Jun  9 09:48 /dev/ttySC0
crw-rw---- 1 root dialout 235, 1 Jun  9 09:48 /dev/ttySC1
-- chrony sources
210 Number of sources = 2
MS Name/IP address         Stratum Poll Reach LastRx Last sample              
===============================================================================
#? GPS                           0   3     0     -     +0ns[   +0ns] +/-    0ns
#? PPS                           0   3     0     -     +0ns[   +0ns] +/-    0ns
-- chrony tracking
Reference ID    : 00000000 ()
Stratum         : 0
Ref time (UTC)  : Thu Jan 01 00:00:00 1970
System time     : 0.000000038 seconds fast of NTP time
Last offset     : +0.000000000 seconds
RMS offset      : 0.000000000 seconds
Frequency       : 12.199 ppm fast
Residual freq   : +0.000 ppm
Skew            : 0.000 ppm
Root delay      : 1.000000000 seconds
Root dispersion : 1.000000000 seconds
Update interval : 0.0 seconds
Leap status     : Not synchronised
-- chrony sourcestats
210 Number of sources = 2
Name/IP Address            NP  NR  Span  Frequency  Freq Skew  Offset  Std Dev
==============================================================================
GPS                         0   0     0     +0.000   2000.000     +0ns  4000ms
PPS                         0   0     0     +0.000   2000.000     +0ns  4000ms

---- sensors
-rw-r--r-- 1 root root 171 Sep 19  2019 /etc/sensors.d/draws
rpi_volt-isa-0000
Adapter: ISA adapter
in0:              N/A  

ads1015-i2c-1-48
Adapter: bcm2835 I2C adapter
+12V:        +12.91 V  
in5:          +0.55 V  
User ADC 1:   +0.00 V  
User ADC 2:   +0.00 V  


---- throttle
temp=52.0'C
throttled=0x0

---- locale
Locale country codes consistent among WiFi cfg file, iw reg & X11: US
core_config.sh has been run 0 time(s)
===

On Thu, Jul 30, 2020 at 12:41 PM Basil Gunn <basil@...> wrote:

Keating,
Sorry for the delay.

In a previous post you mentioned that you have a second DRAWS hat.

> I was concerned that I had a problem with my image perhaps, but I own
> a second DRAWS, and it shows up just fine.

Just to confirm are you saying that using the same mSD card that one
DRAWS hat is enumerated & another is not?

It sounds like you have a hardware problem.
Could you please send me the output of showudrc.sh on the working DRAWS
hat using the same mSD card used on the non-working DRAWS hat.

I already have the showudrc.sh output of the DRAWS hat that is not
enumerating. I would like to compare the outputs.

Thanks,
/Basil



Keating Floyd <kc4hsi@...> writes:

> Hi,  Basil (et al).
>
> I did as you suggested, and did not even do the "Welcome to the Raspberry
> Pi Desktop" setup.
>
> aplay -l reports "aplay: device_list:272: no soundcards found..."
>
> udrcver.sh reports:
>
>      HAT ID EEPROM
> Name:       hat
> Product:    Digital Radio Amateur Work Station
> Product ID: 0x0004
> Product ver: 0x0204
> UUID: 7499df1d-8bc8-401d-b978-97518d36967e
> Vendor: NW Digital Radio
>
> Thanks,
>
> Keating
>
> On Wed, Jul 29, 2020 at 1:03 PM Keating Floyd via groups.io <kc4hsi=
> gmail.com@groups.io> wrote:
>
>> I believe I was following the getting started guide - but it is possible I
>> did an upgrade first.  I will do exactly as you suggest!
>>
>> Keating
>>
>> On Wed, Jul 29, 2020 at 11:40 AM Basil Gunn <basil@...> wrote:
>>
>>> Keating,
>>>
>>> Using the same Raspberry Pi version & DRAWS hat version as you I booted
>>> a fresh NWDR16 image and could not replicate your symptom.
>>>
>>> The first thing to do after booting a new image is to run
>>> aplay -l
>>> which will tell you if the driver and overlays have loaded properly.
>>> This is described in the Getting Started Guide
>>> https://nw-digital-radio.groups.io/g/udrc/wiki/8921
>>>
>>> What where the steps you took after your first boot of a new image?
>>> ie. did you run apt-get update, or raspi-config, or pi-wiz setup?
>>>
>>> I would like you to try and replicate what I did which is to burn the
>>> image, boot & run aplay -l so that we can figure out what is causing
>>> your problem.
>>>
>>>  $ udrcver.sh
>>> Found a DRAWS
>>>
>>>      HAT ID EEPROM
>>> Name:        hat
>>> Product:     Digital Radio Amateur Work Station
>>> Product ID:  0x0004
>>> Product ver: 0x0204
>>> UUID:        4a0b1dce-358e-4b50-a372-1118a9ecbfed
>>> Vendor:      NW Digital Radio
>>>
>>> pi@raspberrypi:~ $ piver.sh
>>>  Pi 4 Model B, Rev 1.1, 4GB mem, Mfg by Sony UK
>>>  Has WiFi
>>>
>>> pi@raspberrypi:~ $ aplay -l | grep udrc
>>> card 2: udrc [udrc], device 0: bcm2835-i2s-tlv320aic32x4-hifi
>>> tlv320aic32x4-hifi-0 [bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4-hifi-0]
>>>
>>> /Basil n7nix
>>>
>>> Keating Floyd <kc4hsi@...> writes:
>>>
>>> > Hi, Basil, and thanks!
>>> >
>>> > Yes, I have a wireless keyboard dongle plugged in there.
>>> >
>>> > Keating
>>> >
>>> >
>>> > On Tue, Jul 28, 2020, 9:36 PM Basil Gunn <basil@...> wrote:
>>> >
>>> >>
>>> >> Keating,
>>> >> I am looking into your problem.
>>> >> Could you please tell me if you have anything plugged into the USB
>>> >> ports on your RPi 4.
>>> >> Thanks,
>>> >> /Basil
>>> >>
>>> >> Keating Floyd <kc4hsi@...> writes:
>>> >>
>>> >> > Included is the output from showudrc.sh. I was concerned that I had a
>>> >> problem with my image perhaps, but I own a second DRAWS, and it shows
>>> up
>>> >> just fine.
>>> >> >
>>> >> > Thanks for a great product, and for your help.
>>> >> >
>>> >> > Keating
>>> >> >
>>> >> > ===
>>> >> >
>>> >> > root@pi4b4g01:/home/pi/n7nix/hfprogs# cat showudrc.sh_out
>>> >> > ==== Sound Card ====
>>> >> > No udrc sound card found.
>>> >> > ==== Pi Ver ====
>>> >> > Pi 4 Model B, Rev 1.1, 4GB mem, Mfg by Sony UK
>>> >> > Has WiFi
>>> >> > ==== udrc Ver ====
>>> >> > Found a DRAWS
>>> >> >
>>> >> > HAT ID EEPROM
>>> >> > Name:    hat
>>> >> > Product:  Digital Radio Amateur Work Station
>>> >> > Product ID: 0x0004
>>> >> > Product ver: 0x0204
>>>
>>>
>>>
>>>
>>
>>
>
>





Basil Gunn
 

Keating,
Thank you for the showudrc.sh output. I think you have 2 mSD cards
based upon 2 different hostnames. What happens if you use the mSD card
with hostname raspberrypi with the DRAWS hat that fails.

Also could you please refresh the n7nix repository on both your mSD
cards.

cd
cd n7nix
git pull
cd config
./bin_refresh.sh

then run the showudrc.sh script using the mSD card with hostname
raspberrypi with the failing DRAWS hat.

Thanks,
/Basil n7nix


Keating Floyd <kc4hsi@...> writes:

Hi, Basil.

Here is the output, using the other DRAWS hat.

===
==== Sound Card ====
udrc card number line: card 2: udrc [udrc], device 0:
bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4-hifi-0
[bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4-hifi-0]
udrc is sound card #2


Keating Floyd
 

Hi, Basil.  Here is the output for your request.  I put the output of "aplay -l" at the head of the file.

Keating

====
aplay
==== Sound Card ====
No udrc sound card found.

==== Pi Ver ====
 Pi 4 Model B, Rev 1.1, 4GB mem, Mfg by Sony UK
 Has WiFi
Hardware : BCM2835
Revision : c03111
Serial : 10000000eed8e22f
Model : Raspberry Pi 4 Model B Rev 1.1

==== Pi Firmware VideoCore Ver ====
Jun  1 2020 13:23:40
Copyright (c) 2012 Broadcom
version 6379679d1ec6a8c746d7e77e015f5b56b939976f (clean) (release) (start)

==== Pi Firmware EEPROM Ver ====
Apr 16 2020 18:11:26
version a5e1b95f320810c69441557c5f5f0a7f2460dfb8 (release)
timestamp 1587057086

==== Pi Firmware EEPROM Config ====
[all]
BOOT_UART=0
WAKE_ON_GPIO=1
POWER_OFF_ON_HALT=0
DHCP_TIMEOUT=45000
DHCP_REQ_TIMEOUT=4000
TFTP_FILE_TIMEOUT=30000
TFTP_IP=
TFTP_PREFIX=0
BOOT_ORDER=0x1
SD_BOOT_MAX_RETRIES=3
NET_BOOT_MAX_RETRIES=5
[none]
FREEZE_VERSION=0

==== udrc Ver ====
Found a DRAWS

     HAT ID EEPROM
Name:        hat
Product:     Digital Radio Amateur Work Station
Product ID:  0x0004
Product ver: 0x0204
UUID:        7499df1d-8bc8-401d-b978-97518d36967e
Vendor:      NW Digital Radio

==== sys Ver ====
----- image version
2020 06 08 11:50:00 PDT: SD image version: nwdr16
----- /proc/version
Linux version 4.19.118-v7l+ (dom@buildbot) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1311 SMP Mon Apr 27 14:26:42 BST 2020

----- /etc/*version: 10.4

----- /etc/*release
PRETTY_NAME="Raspbian GNU/Linux 10 (buster)"
NAME="Raspbian GNU/Linux"
VERSION_ID="10"
VERSION="10 (buster)"
VERSION_CODENAME=buster
ID=raspbian
ID_LIKE=debian
HOME_URL="http://www.raspbian.org/"
SUPPORT_URL="http://www.raspbian.org/RaspbianForums"
BUG_REPORT_URL="http://www.raspbian.org/RaspbianBugs"

----- lsb_release
Distributor ID: Raspbian
Description: Raspbian GNU/Linux 10 (buster)
Release: 10
Codename: buster

---- systemd
   Static hostname: raspberrypi
         Icon name: computer
        Machine ID: 27ac1f0c20904cb7a960920e966db545
           Boot ID: 8c0aadc00fd94f92add9460183cfcedf
  Operating System: Raspbian GNU/Linux 10 (buster)
            Kernel: Linux 4.19.118-v7l+
      Architecture: arm
        sd card id: 9f5449535043432010169900d0014100

---- modules

---- kernel
|/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad)
||/ Name               Version      Architecture Description
+++-==================-============-============-=================================
ii  raspberrypi-kernel 1.20200601-1 armhf        Raspberry Pi bootloader

---- Codec drivers
Found: snd-soc-tlv320aic32x4-i2c.ko, OK
Found: snd-soc-tlv320aic32x4.ko, OK

Directory: /proc/device-tree/soc/i2c@7e804000/tlv320aic32x4@18 does NOT exist

Directory: /proc/device-tree/soc/i2c@7e804000 exists and status is disabled

---- syslog

---- dmesg


----- Dire Wolf DEVELOPMENT version 1.6 E (May 11 2020)

==== Filesystem ====
/dev/root        29G  5.0G   23G  19% /

==== boot config ====

[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
dtoverlay=vc4-fkms-v3d

[all]
#dtoverlay=vc4-fkms-v3d

# Flush all overlays, ie. deprecated overlays loaded from eeprom
dtoverlay=
# enable udrc/draws if no eeprom
dtoverlay=draws,alsaname=udrc
force_turbo=1
# Enable audio (loads snd_bcm2835)
dtparam=audio=on

---- gpsd
/usr/local/sbin/gpsd
gpsd: 3.20 (revision 3.20)
● gpsd.service - GPS (Global Positioning System) Daemon
   Loaded: loaded (/lib/systemd/system/gpsd.service; enabled; vendor preset: enabled)
   Active: active (running) since Wed 2020-06-10 03:35:36 EDT; 12min ago
  Process: 561 ExecStart=/usr/local/sbin/gpsd $GPSD_OPTIONS $OPTIONS $DEVICES (code=exited, status=0/SUCCESS)
 Main PID: 567 (gpsd)
    Tasks: 1 (limit: 4915)
   Memory: 1.1M
   CGroup: /system.slice/gpsd.service
           └─567 /usr/local/sbin/gpsd -n /dev/ttySC0 /dev/pps0

Jun 10 03:35:36 raspberrypi systemd[1]: Starting GPS (Global Positioning System) Daemon...
Jun 10 03:35:36 raspberrypi systemd[1]: Started GPS (Global Positioning System) Daemon.
Jun 10 03:35:36 raspberrypi gpsd[567]: gpsd:ERROR: SER: device open of /dev/ttySC0 failed: No such file or directory - retrying read-only
Jun 10 03:35:36 raspberrypi gpsd[567]: gpsd:ERROR: SER: read-only device open of /dev/ttySC0 failed: No such file or directory
Jun 10 03:35:36 raspberrypi gpsd[567]: gpsd:ERROR: initial GPS device /dev/ttySC0 open failed
Jun 10 03:35:36 raspberrypi gpsd[567]: gpsd:ERROR: SER: device open of /dev/pps0 failed: No such file or directory - retrying read-only
Jun 10 03:35:36 raspberrypi gpsd[567]: gpsd:ERROR: SER: read-only device open of /dev/pps0 failed: No such file or directory
Jun 10 03:35:36 raspberrypi gpsd[567]: gpsd:ERROR: initial GPS device /dev/pps0 open failed

---- chrony
-- chrony sources
210 Number of sources = 2
MS Name/IP address         Stratum Poll Reach LastRx Last sample              
===============================================================================
#? GPS                           0   3     0     -     +0ns[   +0ns] +/-    0ns
#? PPS                           0   3     0     -     +0ns[   +0ns] +/-    0ns
-- chrony tracking
Reference ID    : 00000000 ()
Stratum         : 0
Ref time (UTC)  : Thu Jan 01 00:00:00 1970
System time     : 0.000000010 seconds fast of NTP time
Last offset     : +0.000000000 seconds
RMS offset      : 0.000000000 seconds
Frequency       : 12.199 ppm fast
Residual freq   : +0.000 ppm
Skew            : 0.000 ppm
Root delay      : 1.000000000 seconds
Root dispersion : 1.000000000 seconds
Update interval : 0.0 seconds
Leap status     : Not synchronised
-- chrony sourcestats
210 Number of sources = 2
Name/IP Address            NP  NR  Span  Frequency  Freq Skew  Offset  Std Dev
==============================================================================
GPS                         0   0     0     +0.000   2000.000     +0ns  4000ms
PPS                         0   0     0     +0.000   2000.000     +0ns  4000ms

---- sensors
-rw-r--r-- 1 root root 171 Sep 19  2019 /etc/sensors.d/draws
rpi_volt-isa-0000
Adapter: ISA adapter
in0:              N/A  


---- throttle
temp=50.0'C
throttled=0x0

---- locale
Locale country codes consistent among WiFi cfg file, iw reg & X11: US
core_config.sh has been run 0 time(s)


On Fri, Jul 31, 2020 at 2:12 PM Basil Gunn <basil@...> wrote:

Keating,
Thank you for the showudrc.sh output.  I think you have 2 mSD cards
based upon 2 different hostnames. What happens if you use the mSD card
with hostname raspberrypi with the DRAWS hat that fails.

Also could you please refresh the n7nix repository on both your mSD
cards.

cd
cd n7nix
git pull
cd config
./bin_refresh.sh

then run the showudrc.sh script using the mSD card with hostname
raspberrypi with the failing DRAWS hat.

Thanks,
/Basil n7nix


Keating Floyd <kc4hsi@...> writes:

> Hi, Basil.
>
> Here is the output, using the other DRAWS hat.
>
> ===
> ==== Sound Card ====
> udrc card number line: card 2: udrc [udrc], device 0:
> bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4-hifi-0
> [bcm2835-i2s-tlv320aic32x4-hifi tlv320aic32x4-hifi-0]
> udrc is sound card #2