Topics

no transmit #wsjt-x

Rob Lapham
 

I've been trying to get my Raspberry Pi 3 working with my DRAWS hat but I think either my connection is messed up or my audio setup / levels wrong.
 
I think Im doing something wrong I have used the draws manager and no transmit
 
## Symptoms
- receive work
- Nothing on ALC meter when I tune with WSJT-X
 
## Hardware
 
- Yaesu FT-817
- Raspberry Pi 3
- DRAWS hat
 
## Settings
 
- 24 Dig Disp: 0Hz
- 25 Dig Mic: 61
- 26 Dig Mode: User-U
- 27 Dig Shift: 0Hz
- 38 Op Filter: Off
- AGC: Fast
- Noise Blanker: Off
 
## Connections
 
-with and without  Pin 6 removed from the Data cable
- Data cable in Left (facing the connectors) jack
- USB Serial CAT cable
- into antenna or dummy load
 
## WSJT-X Setup
 
- CAT control set up and working
- Input: plughw:CARD=udrc,DEV=0 in left
- Output: plughw:CARD=udrc,DEV=0 in left
 
I've tried Left, Right, and other udrc input devices to no success)
 
## ALSA Setup
 
I ran the setup-ft817.sh script to set my levels:
 
 ===== ALSA Controls for Radio Transmit =====
LO Driver Gain  L:[-6.00dB] R:[-6.00dB]
PCM         L:[-16.50dB] R:[-16.50dB]
DAC Playback PT L:[PTM_P3] R:[PTM_P3]
LO Playback CM [Full Chip CM]
 ===== ALSA Controls for Radio Receive =====
ADC Level L:[-2.00dB] R:[-2.00dB]
IN1  L:[Off]  R:[Off]
IN2  L:[10 kOhm] R:[Off]
CM  L:[10 kOhm] R:[10 kOhm]
Thanks,
Rob
k6jus

Basil Gunn
 

Rob,

Verify that transmit is working with the simplest program possible.
Use the measure_deviate.sh script to output a tone on a specific
channel. Assuming you are using the mDin6 connector closest to the gps
SMA connector. If you tune a second radio to the same frequency as the
first you should hear a tone.

cd
cd n7nix/deviation
./measure_deviate.sh -c left

To see the command line parameter options:
./measure_deviate.sh -h

Also send the console output of showudrc.sh

/Basil

Rob Lapham <ke6jus@...> writes:

I've been trying to get my Raspberry Pi 3 working with my DRAWS hat but I think either my connection is messed up or my audio setup / levels wrong.

I think Im doing something wrong I have used the draws manager and no transmit

## Symptoms
- receive work
- Nothing on ALC meter when I tune with WSJT-X

## Hardware

- Yaesu FT-817
- Raspberry Pi 3
- DRAWS hat

## Settings

- 24 Dig Disp: 0Hz
- 25 Dig Mic: 61
- 26 Dig Mode: User-U
- 27 Dig Shift: 0Hz
- 38 Op Filter: Off
- AGC: Fast
- Noise Blanker: Off

## Connections

-with and without Pin 6 removed from the Data cable
- Data cable in Left (facing the connectors) jack
- USB Serial CAT cable
- into antenna or dummy load

## WSJT-X Setup

- CAT control set up and working
- Input: plughw:CARD=udrc,DEV=0 in left
- Output: plughw:CARD=udrc,DEV=0 in left

I've tried Left, Right, and other udrc input devices to no success)

## ALSA Setup

I ran the setup-ft817.sh script to set my levels:

===== ALSA Controls for Radio Transmit =====
LO Driver Gain L:[-6.00dB]R:[-6.00dB]
PCM L:[-16.50dB]R:[-16.50dB]
DAC Playback PTL:[PTM_P3]R:[PTM_P3]
LO Playback CM[Full Chip CM]
===== ALSA Controls for Radio Receive =====
ADC LevelL:[-2.00dB]R:[-2.00dB]
IN1L:[Off]R:[Off]
IN2L:[10 kOhm]R:[Off]
CML:[10 kOhm]R:[10 kOhm]
Thanks,
Rob
k6jus

Rob Lapham
 

Run your test and it keyed the transmitter but
no audio on my other receiver. Did make kind of 
a motor boating sound 
here is that file

==== Sound Card ====

udrc card number line: card 1: udrc [udrc], device 0: Universal Digital Radio Controller tlv320aic32x4-hifi-0 []

udrc is sound card #1

==== ALSA Controls for Radio Tansmit ====

LO Driver Gain  L:[-6.00dB]           R:[-6.00dB]

PCM              L:[-21.00dB]               R:[-21.00dB]

DAC Playback PT               L:[PTM_P3]        R:[PTM_P3]

LO Playback CM [Full Chip CM]

==== ALSA Controls for Radio Receive ====

ADC Level            L:[-2.00dB]          R:[-2.00dB]

IN1                         L:[Off]                   R:[Off]

IN2                         L:[10 kOhm]       R:[Off]

==== Pi Ver ====

Pi 3 Model B+ Mfg by Sony UK

Has WiFi

==== udrc Ver ====

Found a DRAWS

 

     HAT ID EEPROM

Name:        hat

Product:     Digital Radio Amateur Work Station

Product ID:  0x0004

Product ver: 0x0106

UUID:        9598845d-e110-49ce-9287-d770da081361

Vendor:      NW Digital Radio

 

==== sys Ver ====

----- image version

2019 05 07 12:46:37 PDT: SD image version: beta13

----- /proc/version

Linux version 4.14.98-v7+ (dom@dom-XPS-13-9370) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1200 SMP Tue Feb 12 20:27:48 GMT 2019

 

----- /etc/*version: 9.9

 

----- /etc/*release

PRETTY_NAME="Raspbian GNU/Linux 9 (stretch)"

NAME="Raspbian GNU/Linux"

VERSION_ID="9"

VERSION="9 (stretch)"

ID=raspbian

ID_LIKE=debian

HOME_URL="http://www.raspbian.org/"

SUPPORT_URL="http://www.raspbian.org/RaspbianForums"

BUG_REPORT_URL="http://www.raspbian.org/RaspbianBugs"

 

----- lsb_release

No LSB modules are available.

Distributor ID:    Raspbian

Description:        Raspbian GNU/Linux 9.9 (stretch)

Release:               9.9

Codename:        stretch

 

---- systemd

   Static hostname: k6jus

         Icon name: computer

        Machine ID: 2f51e140e908474eaa86ae805f03a6d8

           Boot ID: 82a002c5803b4ad6b105b8b8d68612b5

  Operating System: Raspbian GNU/Linux 9 (stretch)

            Kernel: Linux 4.14.98-v7+

      Architecture: arm

 

---- modules

tlv320aic32x4_i2c      16384  1

tlv320aic32x4          32768  1 tlv320aic32x4_i2c

udrc                   16384  2

snd_soc_core          188416  3 tlv320aic32x4,snd_soc_bcm2835_i2s,udrc

snd_pcm                98304  5 snd_pcm_dmaengine,tlv320aic32x4,snd_soc_bcm2835_i2s,snd_bcm2835,snd_soc_core

 

-rw-r--r-- 1 root  6388 Apr 16 12:42 /lib/modules/4.14.98-v7+/updates/dkms/tlv320aic32x4-i2c.ko

-rw-r--r-- 1 root 39084 Apr 16 12:42 /lib/modules/4.14.98-v7+/updates/dkms/tlv320aic32x4.ko

-rw-r--r-- 1 root  6408 Apr 16 12:42 /lib/modules/4.14.98-v7+/updates/dkms/tlv320aic32x4-spi.ko

-rw-r--r-- 1 root  8332 Apr 16 12:42 /lib/modules/4.14.98-v7+/updates/dkms/udrc.ko

 

---- kernel

||/ Name               Version      Architecture Description

+++-==================-============-============-=================================

ii  raspberrypi-kernel 1.20190401-1 armhf        Raspberry Pi bootloader

ii  udrc-dkms          1.0.5        armhf        DKMS source for the UDRC driver

 

Directory: /proc/device-tree/soc/i2c@7e804000/tlv320aic32x4@18 exists and status is okay

 

---- syslog

Aug 25 17:46:57 k6jus kernel: [    3.358099] udrc: loading out-of-tree module taints kernel.

Aug 25 17:46:57 k6jus kernel: [    3.359645] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 17:46:57 k6jus kernel: [    3.359661] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 17:46:57 k6jus kernel: [    3.408574] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 17:46:57 k6jus kernel: [    3.408590] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 17:46:57 k6jus kernel: [    3.413951] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 17:46:57 k6jus kernel: [    3.413957] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 17:46:57 k6jus kernel: [    3.416855] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 17:46:57 k6jus kernel: [    3.416861] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 17:46:57 k6jus kernel: [    3.424353] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 17:46:57 k6jus kernel: [    3.424365] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 17:46:57 k6jus kernel: [    3.509261] snd-udrc soc:sound: tlv320aic32x4-hifi <-> 3f203000.i2s mapping ok

Aug 25 10:01:02 k6jus kernel: [    3.296915] udrc: loading out-of-tree module taints kernel.

Aug 25 10:01:02 k6jus kernel: [    3.297463] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 10:01:02 k6jus kernel: [    3.297473] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 10:01:02 k6jus kernel: [    3.310120] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 10:01:02 k6jus kernel: [    3.310128] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 10:01:02 k6jus kernel: [    3.310392] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 10:01:02 k6jus kernel: [    3.310404] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 10:01:02 k6jus kernel: [    3.312982] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 10:01:02 k6jus kernel: [    3.312994] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 10:01:02 k6jus kernel: [    3.424920] snd-udrc soc:sound: tlv320aic32x4-hifi <-> 3f203000.i2s mapping ok

Aug 25 10:57:36 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_L to Left Mixer Positive Resistor' '10 kOhm'

Aug 25 10:57:36 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_L to Left Mixer Positive Resistor' 'Off'

Aug 25 10:57:36 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_R to Right Mixer Positive Resistor' 'Off'

Aug 25 10:57:37 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_R to Right Mixer Positive Resistor' 'Off'

Aug 25 10:57:37 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_R to Right Mixer Negative Resistor' '10 kOhm'

Aug 25 10:57:37 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_L to Left Mixer Negative Resistor' '10 kOhm'

Aug 25 10:57:37 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO DAC' 'on,off'

Aug 25 10:57:37 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOL Output Mixer L_DAC' 'on'

Aug 25 10:57:38 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOR Output Mixer R_DAC' 'off'

Aug 25 10:57:40 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_L to Left Mixer Positive Resistor' '10 kOhm'

Aug 25 10:57:40 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_L to Left Mixer Positive Resistor' 'Off'

Aug 25 10:57:40 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_R to Right Mixer Positive Resistor' 'Off'

Aug 25 10:57:41 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_R to Right Mixer Positive Resistor' 'Off'

Aug 25 10:57:41 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_R to Right Mixer Negative Resistor' '10 kOhm'

Aug 25 10:57:41 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_L to Left Mixer Negative Resistor' '10 kOhm'

Aug 25 10:57:41 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO DAC' 'on,off'

Aug 25 10:57:41 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOL Output Mixer L_DAC' 'on'

Aug 25 10:57:41 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOR Output Mixer R_DAC' 'off'

Aug 25 10:57:42 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO Driver Gain' '0,0'

Aug 25 10:57:42 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'ADC Level' '20,20'

Aug 25 10:57:42 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'PCM' '94,97'

Aug 25 10:57:42 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'DAC Left Playback PowerTune' 'PTM_P3'

Aug 25 11:09:45 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_L to Left Mixer Positive Resistor' 'Off'

Aug 25 11:09:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_L to Left Mixer Positive Resistor' 'Off'

Aug 25 11:09:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_R to Right Mixer Positive Resistor' 'Off'

Aug 25 11:09:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_R to Right Mixer Positive Resistor' 'Off'

Aug 25 11:09:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_R to Right Mixer Negative Resistor' '10 kOhm'

Aug 25 11:09:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_L to Left Mixer Negative Resistor' '10 kOhm'

Aug 25 11:09:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO DAC' 'off,off'

Aug 25 11:09:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOL Output Mixer L_DAC' 'off'

Aug 25 11:09:47 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOR Output Mixer R_DAC' 'off'

Aug 25 11:09:49 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_L to Left Mixer Positive Resistor' 'Off'

Aug 25 11:09:50 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_L to Left Mixer Positive Resistor' 'Off'

Aug 25 11:09:50 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_R to Right Mixer Positive Resistor' '10 kOhm'

Aug 25 11:09:50 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_R to Right Mixer Positive Resistor' 'Off'

Aug 25 11:09:50 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_R to Right Mixer Negative Resistor' '10 kOhm'

Aug 25 11:09:50 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_L to Left Mixer Negative Resistor' '10 kOhm'

Aug 25 11:09:50 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO DAC' 'off,on'

Aug 25 11:09:50 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOL Output Mixer L_DAC' 'off'

Aug 25 11:09:51 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOR Output Mixer R_DAC' 'on'

Aug 25 11:09:51 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO Driver Gain' '0,0'

Aug 25 11:09:51 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'ADC Level' '20,20'

Aug 25 11:09:51 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'PCM' '94,94'

Aug 25 11:09:51 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'DAC Right Playback PowerTune' 'PTM_P3'

Aug 25 11:17:44 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_L to Left Mixer Positive Resistor' '10 kOhm'

Aug 25 11:17:44 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_L to Left Mixer Positive Resistor' 'Off'

Aug 25 11:17:44 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_R to Right Mixer Positive Resistor' '10 kOhm'

Aug 25 11:17:44 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_R to Right Mixer Positive Resistor' 'Off'

Aug 25 11:17:44 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_R to Right Mixer Negative Resistor' '10 kOhm'

Aug 25 11:17:45 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_L to Left Mixer Negative Resistor' '10 kOhm'

Aug 25 11:17:45 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO DAC' 'on,on'

Aug 25 11:17:45 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOL Output Mixer L_DAC' 'on'

Aug 25 11:17:45 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOR Output Mixer R_DAC' 'on'

Aug 25 11:17:45 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO Driver Gain' '0,0'

Aug 25 11:17:45 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'ADC Level' '20,20'

Aug 25 11:17:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'PCM' '94,94'

Aug 25 11:17:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'DAC Left Playback PowerTune' 'PTM_P3'

Aug 25 11:17:47 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_L to Left Mixer Positive Resistor' '10 kOhm'

Aug 25 11:17:47 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_L to Left Mixer Positive Resistor' 'Off'

Aug 25 11:17:47 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_R to Right Mixer Positive Resistor' 'Off'

Aug 25 11:17:48 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_R to Right Mixer Positive Resistor' 'Off'

Aug 25 11:17:48 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_R to Right Mixer Negative Resistor' '10 kOhm'

Aug 25 11:17:48 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_L to Left Mixer Negative Resistor' '10 kOhm'

Aug 25 11:17:48 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO DAC' 'on,off'

Aug 25 11:17:48 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOL Output Mixer L_DAC' 'on'

Aug 25 11:17:48 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOR Output Mixer R_DAC' 'off'

Aug 25 11:55:47 k6jus kernel: [    3.257893] udrc: loading out-of-tree module taints kernel.

Aug 25 11:55:47 k6jus kernel: [    3.258840] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 11:55:47 k6jus kernel: [    3.258853] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 11:55:47 k6jus kernel: [    3.359451] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 11:55:47 k6jus kernel: [    3.359465] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 11:55:47 k6jus kernel: [    3.366761] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 11:55:47 k6jus kernel: [    3.366768] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 11:55:47 k6jus kernel: [    3.462604] snd-udrc soc:sound: tlv320aic32x4-hifi <-> 3f203000.i2s mapping ok

 

---- dmesg

[    3.257893] udrc: loading out-of-tree module taints kernel.

[    3.258840] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

[    3.258853] snd-udrc soc:sound: snd_soc_register_card() failed: -517

[    3.359451] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

[    3.359465] snd-udrc soc:sound: snd_soc_register_card() failed: -517

[    3.366761] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

[    3.366768] snd-udrc soc:sound: snd_soc_register_card() failed: -517

[    3.462604] snd-udrc soc:sound: tlv320aic32x4-hifi <-> 3f203000.i2s mapping ok

 

---- compass

Compass preference file not found: /etc/apt/preferences.d/compass

---- compass apt sources list file

deb [arch=armhf,amd64] http://archive.compasslinux.org/ cedar main

---- compass package files

-rw-r--r-- 1 root  2201 Dec 31  2018 /var/lib/apt/lists/archive.compasslinux.org_dists_cedar_InRelease

-rw-r--r-- 1 root 17567 Jul  2  2018 /var/lib/apt/lists/archive.compasslinux.org_dists_cedar_main_binary-amd64_Packages

-rw-r--r-- 1 root 43316 Dec 31  2018 /var/lib/apt/lists/archive.compasslinux.org_dists_cedar_main_binary-armhf_Packages

 

----- Dire Wolf DEVELOPMENT version 1.6 B (Feb 27 2019)

 

==== Filesystem ====

/dev/root        30G  4.9G   24G  18% /

 

==== boot config ====

# Uncomment some or all of these to enable the optional hardware interfaces

#dtparam=i2c_arm=on

#dtparam=i2s=on

#dtparam=spi=on

 

# Uncomment this to enable the lirc-rpi module

#dtoverlay=lirc-rpi

 

# Additional overlays and parameters are documented /boot/overlays/README

 

force_turbo=1

 

force_turbo=1

dtoverlay=

dtoverlay=draws,alsaname=udrc

# Enable audio (loads snd_bcm2835)

dtparam=audio=on

 

---- gpsd

/usr/local/sbin/gpsd

gpsd: 3.18.1 (revision 3.18.1)

● gpsd.service - GPS (Global Positioning System) Daemon

   Loaded: loaded (/lib/systemd/system/gpsd.service; enabled; vendor preset: enabled)

   Active: active (running) since Sun 2019-08-25 11:55:49 PDT; 1 day 6h ago

  Process: 496 ExecStart=/usr/local/sbin/gpsd $GPSD_OPTIONS $OPTIONS $DEVICES (code=exited, status=0/SUCCESS)

Main PID: 499 (gpsd)

   CGroup: /system.slice/gpsd.service

           └─499 /usr/local/sbin/gpsd -n /dev/ttySC0 /dev/pps0

 

Aug 25 11:55:49 k6jus systemd[1]: Starting GPS (Global Positioning System) Daemon...

Aug 25 11:55:49 k6jus systemd[1]: Started GPS (Global Positioning System) Daemon.

 

---- chrony

crw-rw---- 1 root root    243, 0 Aug 25 11:55 /dev/pps0

crw------- 1 root root    243, 1 Aug 25 11:55 /dev/pps1

crw-rw---- 1 root dialout 242, 0 Aug 25 11:55 /dev/ttySC0

crw-rw---- 1 root dialout 242, 1 Aug 25 11:55 /dev/ttySC1

-- chrony sources

210 Number of sources = 6

MS Name/IP address         Stratum Poll Reach LastRx Last sample              

===============================================================================

#? GPS                           0   3     0     -     +0ns[   +0ns] +/-    0ns

#? PPS                           0   3     0     -     +0ns[   +0ns] +/-    0ns

^+ atl0.jane.mattnordhoff.n>     2   9   377   236  -2634us[-2634us] +/-   58ms

^+ shed.galexander.org           3   9   377   427   +914us[ +914us] +/-   77ms

^+ au.kashra.pictures            2   6   377    46  -3876us[-3876us] +/-  114ms

^* sombrero.spiderspace.co.>     2   9   171  1011  +3636us[+3851us] +/-   53ms

-- chrony tracking

Reference ID    : B9D51A8F (sombrero.spiderspace.co.uk)

Stratum         : 3

Ref time (UTC)  : Tue Aug 27 00:42:52 2019

System time     : 0.000259197 seconds fast of NTP time

Last offset     : +0.000215801 seconds

RMS offset      : 0.000593573 seconds

Frequency       : 6.075 ppm slow

Residual freq   : +0.032 ppm

Skew            : 0.699 ppm

Root delay      : 0.102040 seconds

Root dispersion : 0.003672 seconds

Update interval : 257.0 seconds

Leap status     : Normal

-- chrony sourcestats

210 Number of sources = 6

Name/IP Address            NP  NR  Span  Frequency  Freq Skew  Offset  Std Dev

==============================================================================

GPS                         0   0     0     +0.000   2000.000     +0ns  4000ms

PPS                         0   0     0     +0.000   2000.000     +0ns  4000ms

atl0.jane.mattnordhoff.n>  28  14   54m     -0.017      0.849  -1126us   991us

shed.galexander.org        27  16   47m     -0.211      1.174  -1002us  1329us

au.kashra.pictures          7   5   519     -0.645     10.414  -3117us   756us

sombrero.spiderspace.co.>  26  14   41m     -0.165      0.780  +3008us   717us

 

---- sensors

-rw-r--r-- 1 root root 171 Nov 11  2018 /etc/sensors.d/draws

ads1015-i2c-1-48

Adapter: bcm2835 I2C adapter

User ADC Differential:  +0.00 V  

+12V:                  +12.34 V  

User ADC 1:             +0.00 V  

User ADC 2:             +0.00 V  

 

---- locale

Locale country codes consistent among WiFi cfg file, iw reg & X11: US

core_config.sh has been run 1 time(s)

 

Sent from Mail for Windows 10

 

Basil Gunn
 

Rob,
While the transmitter is keyed use alsamixer to change LO Driver Gain &
PCM until you hear a solid tone from your other radio.
Did you use John's web apps to calc the LO Driver Gain & PCM values?
Is your radio configured to use AFOUT?
/Basil

Rob Lapham <ke6jus@...> writes:

Run your test and it keyed the transmitter but
no audio on my other receiver. Did make kind of
a motor boating sound
here is that file

==== Sound Card ====

udrc card number line: card 1: udrc [udrc], device 0: Universal Digital Radio Controller tlv320aic32x4-hifi-0 []

udrc is sound card #1

==== ALSA Controls for Radio Tansmit ====

LO Driver Gain L:[-6.00dB] R:[-6.00dB]

PCM L:[-21.00dB] R:[-21.00dB]

DAC Playback PT L:[PTM_P3] R:[PTM_P3]

LO Playback CM [Full Chip CM]

==== ALSA Controls for Radio Receive ====

ADC Level L:[-2.00dB] R:[-2.00dB]

IN1 L:[Off] R:[Off]

IN2 L:[10 kOhm] R:[Off]

==== Pi Ver ====

Pi 3 Model B+ Mfg by Sony UK

Has WiFi

==== udrc Ver ====

Found a DRAWS

HAT ID EEPROM

Name: hat

Product: Digital Radio Amateur Work Station

Product ID: 0x0004

Product ver: 0x0106

UUID: 9598845d-e110-49ce-9287-d770da081361

Vendor: NW Digital Radio

==== sys Ver ====

----- image version

2019 05 07 12:46:37 PDT: SD image version: beta13

----- /proc/version

Linux version 4.14.98-v7+ (dom@dom-XPS-13-9370) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1200 SMP Tue Feb 12 20:27:48 GMT 2019

----- /etc/*version: 9.9

----- /etc/*release

PRETTY_NAME="Raspbian GNU/Linux 9 (stretch)"

NAME="Raspbian GNU/Linux"

VERSION_ID="9"

VERSION="9 (stretch)"

ID=raspbian

ID_LIKE=debian

HOME_URL="http://www.raspbian.org/"

SUPPORT_URL="http://www.raspbian.org/RaspbianForums"

BUG_REPORT_URL="http://www.raspbian.org/RaspbianBugs"

----- lsb_release

No LSB modules are available.

Distributor ID: Raspbian

Description: Raspbian GNU/Linux 9.9 (stretch)

Release: 9.9

Codename: stretch

---- systemd

Static hostname: k6jus

Icon name: computer

Machine ID: 2f51e140e908474eaa86ae805f03a6d8

Boot ID: 82a002c5803b4ad6b105b8b8d68612b5

Operating System: Raspbian GNU/Linux 9 (stretch)

Kernel: Linux 4.14.98-v7+

Architecture: arm

---- modules

tlv320aic32x4_i2c 16384 1

tlv320aic32x4 32768 1 tlv320aic32x4_i2c

udrc 16384 2

snd_soc_core 188416 3 tlv320aic32x4,snd_soc_bcm2835_i2s,udrc

snd_pcm 98304 5 snd_pcm_dmaengine,tlv320aic32x4,snd_soc_bcm2835_i2s,snd_bcm2835,snd_soc_core

-rw-r--r-- 1 root 6388 Apr 16 12:42 /lib/modules/4.14.98-v7+/updates/dkms/tlv320aic32x4-i2c.ko

-rw-r--r-- 1 root 39084 Apr 16 12:42 /lib/modules/4.14.98-v7+/updates/dkms/tlv320aic32x4.ko

-rw-r--r-- 1 root 6408 Apr 16 12:42 /lib/modules/4.14.98-v7+/updates/dkms/tlv320aic32x4-spi.ko

-rw-r--r-- 1 root 8332 Apr 16 12:42 /lib/modules/4.14.98-v7+/updates/dkms/udrc.ko

---- kernel

||/ Name Version Architecture Description

+++-==================-============-============-=================================

ii raspberrypi-kernel 1.20190401-1 armhf Raspberry Pi bootloader

ii udrc-dkms 1.0.5 armhf DKMS source for the UDRC driver

Directory: /proc/device-tree/soc/i2c@7e804000/tlv320aic32x4@18 exists and status is okay

---- syslog

Aug 25 17:46:57 k6jus kernel: [ 3.358099] udrc: loading out-of-tree module taints kernel.

Aug 25 17:46:57 k6jus kernel: [ 3.359645] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 17:46:57 k6jus kernel: [ 3.359661] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 17:46:57 k6jus kernel: [ 3.408574] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 17:46:57 k6jus kernel: [ 3.408590] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 17:46:57 k6jus kernel: [ 3.413951] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 17:46:57 k6jus kernel: [ 3.413957] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 17:46:57 k6jus kernel: [ 3.416855] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 17:46:57 k6jus kernel: [ 3.416861] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 17:46:57 k6jus kernel: [ 3.424353] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 17:46:57 k6jus kernel: [ 3.424365] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 17:46:57 k6jus kernel: [ 3.509261] snd-udrc soc:sound: tlv320aic32x4-hifi <-> 3f203000.i2s mapping ok

Aug 25 10:01:02 k6jus kernel: [ 3.296915] udrc: loading out-of-tree module taints kernel.

Aug 25 10:01:02 k6jus kernel: [ 3.297463] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 10:01:02 k6jus kernel: [ 3.297473] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 10:01:02 k6jus kernel: [ 3.310120] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 10:01:02 k6jus kernel: [ 3.310128] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 10:01:02 k6jus kernel: [ 3.310392] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 10:01:02 k6jus kernel: [ 3.310404] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 10:01:02 k6jus kernel: [ 3.312982] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 10:01:02 k6jus kernel: [ 3.312994] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 10:01:02 k6jus kernel: [ 3.424920] snd-udrc soc:sound: tlv320aic32x4-hifi <-> 3f203000.i2s mapping ok

Aug 25 10:57:36 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_L to Left Mixer Positive Resistor' '10 kOhm'

Aug 25 10:57:36 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_L to Left Mixer Positive Resistor' 'Off'

Aug 25 10:57:36 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_R to Right Mixer Positive Resistor' 'Off'

Aug 25 10:57:37 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_R to Right Mixer Positive Resistor' 'Off'

Aug 25 10:57:37 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_R to Right Mixer Negative Resistor' '10 kOhm'

Aug 25 10:57:37 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_L to Left Mixer Negative Resistor' '10 kOhm'

Aug 25 10:57:37 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO DAC' 'on,off'

Aug 25 10:57:37 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOL Output Mixer L_DAC' 'on'

Aug 25 10:57:38 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOR Output Mixer R_DAC' 'off'

Aug 25 10:57:40 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_L to Left Mixer Positive Resistor' '10 kOhm'

Aug 25 10:57:40 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_L to Left Mixer Positive Resistor' 'Off'

Aug 25 10:57:40 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_R to Right Mixer Positive Resistor' 'Off'

Aug 25 10:57:41 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_R to Right Mixer Positive Resistor' 'Off'

Aug 25 10:57:41 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_R to Right Mixer Negative Resistor' '10 kOhm'

Aug 25 10:57:41 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_L to Left Mixer Negative Resistor' '10 kOhm'

Aug 25 10:57:41 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO DAC' 'on,off'

Aug 25 10:57:41 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOL Output Mixer L_DAC' 'on'

Aug 25 10:57:41 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOR Output Mixer R_DAC' 'off'

Aug 25 10:57:42 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO Driver Gain' '0,0'

Aug 25 10:57:42 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'ADC Level' '20,20'

Aug 25 10:57:42 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'PCM' '94,97'

Aug 25 10:57:42 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'DAC Left Playback PowerTune' 'PTM_P3'

Aug 25 11:09:45 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_L to Left Mixer Positive Resistor' 'Off'

Aug 25 11:09:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_L to Left Mixer Positive Resistor' 'Off'

Aug 25 11:09:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_R to Right Mixer Positive Resistor' 'Off'

Aug 25 11:09:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_R to Right Mixer Positive Resistor' 'Off'

Aug 25 11:09:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_R to Right Mixer Negative Resistor' '10 kOhm'

Aug 25 11:09:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_L to Left Mixer Negative Resistor' '10 kOhm'

Aug 25 11:09:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO DAC' 'off,off'

Aug 25 11:09:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOL Output Mixer L_DAC' 'off'

Aug 25 11:09:47 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOR Output Mixer R_DAC' 'off'

Aug 25 11:09:49 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_L to Left Mixer Positive Resistor' 'Off'

Aug 25 11:09:50 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_L to Left Mixer Positive Resistor' 'Off'

Aug 25 11:09:50 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_R to Right Mixer Positive Resistor' '10 kOhm'

Aug 25 11:09:50 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_R to Right Mixer Positive Resistor' 'Off'

Aug 25 11:09:50 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_R to Right Mixer Negative Resistor' '10 kOhm'

Aug 25 11:09:50 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_L to Left Mixer Negative Resistor' '10 kOhm'

Aug 25 11:09:50 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO DAC' 'off,on'

Aug 25 11:09:50 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOL Output Mixer L_DAC' 'off'

Aug 25 11:09:51 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOR Output Mixer R_DAC' 'on'

Aug 25 11:09:51 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO Driver Gain' '0,0'

Aug 25 11:09:51 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'ADC Level' '20,20'

Aug 25 11:09:51 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'PCM' '94,94'

Aug 25 11:09:51 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'DAC Right Playback PowerTune' 'PTM_P3'

Aug 25 11:17:44 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_L to Left Mixer Positive Resistor' '10 kOhm'

Aug 25 11:17:44 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_L to Left Mixer Positive Resistor' 'Off'

Aug 25 11:17:44 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_R to Right Mixer Positive Resistor' '10 kOhm'

Aug 25 11:17:44 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_R to Right Mixer Positive Resistor' 'Off'

Aug 25 11:17:44 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_R to Right Mixer Negative Resistor' '10 kOhm'

Aug 25 11:17:45 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_L to Left Mixer Negative Resistor' '10 kOhm'

Aug 25 11:17:45 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO DAC' 'on,on'

Aug 25 11:17:45 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOL Output Mixer L_DAC' 'on'

Aug 25 11:17:45 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOR Output Mixer R_DAC' 'on'

Aug 25 11:17:45 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO Driver Gain' '0,0'

Aug 25 11:17:45 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'ADC Level' '20,20'

Aug 25 11:17:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'PCM' '94,94'

Aug 25 11:17:46 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'DAC Left Playback PowerTune' 'PTM_P3'

Aug 25 11:17:47 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_L to Left Mixer Positive Resistor' '10 kOhm'

Aug 25 11:17:47 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_L to Left Mixer Positive Resistor' 'Off'

Aug 25 11:17:47 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN2_R to Right Mixer Positive Resistor' 'Off'

Aug 25 11:17:48 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'IN1_R to Right Mixer Positive Resistor' 'Off'

Aug 25 11:17:48 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_R to Right Mixer Negative Resistor' '10 kOhm'

Aug 25 11:17:48 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'CM_L to Left Mixer Negative Resistor' '10 kOhm'

Aug 25 11:17:48 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LO DAC' 'on,off'

Aug 25 11:17:48 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOL Output Mixer L_DAC' 'on'

Aug 25 11:17:48 k6jus npm[470]: /usr/bin/amixer -c udrc sset 'LOR Output Mixer R_DAC' 'off'

Aug 25 11:55:47 k6jus kernel: [ 3.257893] udrc: loading out-of-tree module taints kernel.

Aug 25 11:55:47 k6jus kernel: [ 3.258840] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 11:55:47 k6jus kernel: [ 3.258853] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 11:55:47 k6jus kernel: [ 3.359451] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 11:55:47 k6jus kernel: [ 3.359465] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 11:55:47 k6jus kernel: [ 3.366761] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

Aug 25 11:55:47 k6jus kernel: [ 3.366768] snd-udrc soc:sound: snd_soc_register_card() failed: -517

Aug 25 11:55:47 k6jus kernel: [ 3.462604] snd-udrc soc:sound: tlv320aic32x4-hifi <-> 3f203000.i2s mapping ok

---- dmesg

[ 3.257893] udrc: loading out-of-tree module taints kernel.

[ 3.258840] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

[ 3.258853] snd-udrc soc:sound: snd_soc_register_card() failed: -517

[ 3.359451] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

[ 3.359465] snd-udrc soc:sound: snd_soc_register_card() failed: -517

[ 3.366761] snd-udrc soc:sound: ASoC: CODEC DAI tlv320aic32x4-hifi not registered - will retry

[ 3.366768] snd-udrc soc:sound: snd_soc_register_card() failed: -517

[ 3.462604] snd-udrc soc:sound: tlv320aic32x4-hifi <-> 3f203000.i2s mapping ok

---- compass

Compass preference file not found: /etc/apt/preferences.d/compass

---- compass apt sources list file

deb [arch=armhf,amd64] http://archive.compasslinux.org/ cedar main

---- compass package files

-rw-r--r-- 1 root 2201 Dec 31 2018 /var/lib/apt/lists/archive.compasslinux.org_dists_cedar_InRelease

-rw-r--r-- 1 root 17567 Jul 2 2018 /var/lib/apt/lists/archive.compasslinux.org_dists_cedar_main_binary-amd64_Packages

-rw-r--r-- 1 root 43316 Dec 31 2018 /var/lib/apt/lists/archive.compasslinux.org_dists_cedar_main_binary-armhf_Packages

----- Dire Wolf DEVELOPMENT version 1.6 B (Feb 27 2019)

==== Filesystem ====

/dev/root 30G 4.9G 24G 18% /

==== boot config ====

# Uncomment some or all of these to enable the optional hardware interfaces

#dtparam=i2c_arm=on

#dtparam=i2s=on

#dtparam=spi=on

# Uncomment this to enable the lirc-rpi module

#dtoverlay=lirc-rpi

# Additional overlays and parameters are documented /boot/overlays/README

force_turbo=1

force_turbo=1

dtoverlay=

dtoverlay=draws,alsaname=udrc

# Enable audio (loads snd_bcm2835)

dtparam=audio=on

---- gpsd

/usr/local/sbin/gpsd

gpsd: 3.18.1 (revision 3.18.1)

● gpsd.service - GPS (Global Positioning System) Daemon

Loaded: loaded (/lib/systemd/system/gpsd.service; enabled; vendor preset: enabled)

Active: active (running) since Sun 2019-08-25 11:55:49 PDT; 1 day 6h ago

Process: 496 ExecStart=/usr/local/sbin/gpsd $GPSD_OPTIONS $OPTIONS $DEVICES (code=exited, status=0/SUCCESS)

Main PID: 499 (gpsd)

CGroup: /system.slice/gpsd.service

└─499 /usr/local/sbin/gpsd -n /dev/ttySC0 /dev/pps0

Aug 25 11:55:49 k6jus systemd[1]: Starting GPS (Global Positioning System) Daemon...

Aug 25 11:55:49 k6jus systemd[1]: Started GPS (Global Positioning System) Daemon.

---- chrony

crw-rw---- 1 root root 243, 0 Aug 25 11:55 /dev/pps0

crw------- 1 root root 243, 1 Aug 25 11:55 /dev/pps1

crw-rw---- 1 root dialout 242, 0 Aug 25 11:55 /dev/ttySC0

crw-rw---- 1 root dialout 242, 1 Aug 25 11:55 /dev/ttySC1

-- chrony sources

210 Number of sources = 6

MS Name/IP address Stratum Poll Reach LastRx Last sample

===============================================================================

#? GPS 0 3 0 - +0ns[ +0ns] +/- 0ns

#? PPS 0 3 0 - +0ns[ +0ns] +/- 0ns

^+ atl0.jane.mattnordhoff.n> 2 9 377 236 -2634us[-2634us] +/- 58ms

^+ shed.galexander.org 3 9 377 427 +914us[ +914us] +/- 77ms

^+ au.kashra.pictures 2 6 377 46 -3876us[-3876us] +/- 114ms

^* sombrero.spiderspace.co.> 2 9 171 1011 +3636us[+3851us] +/- 53ms

-- chrony tracking

Reference ID : B9D51A8F (sombrero.spiderspace.co.uk)

Stratum : 3

Ref time (UTC) : Tue Aug 27 00:42:52 2019

System time : 0.000259197 seconds fast of NTP time

Last offset : +0.000215801 seconds

RMS offset : 0.000593573 seconds

Frequency : 6.075 ppm slow

Residual freq : +0.032 ppm

Skew : 0.699 ppm

Root delay : 0.102040 seconds

Root dispersion : 0.003672 seconds

Update interval : 257.0 seconds

Leap status : Normal

-- chrony sourcestats

210 Number of sources = 6

Name/IP Address NP NR Span Frequency Freq Skew Offset Std Dev

==============================================================================

GPS 0 0 0 +0.000 2000.000 +0ns 4000ms

PPS 0 0 0 +0.000 2000.000 +0ns 4000ms

atl0.jane.mattnordhoff.n> 28 14 54m -0.017 0.849 -1126us 991us

shed.galexander.org 27 16 47m -0.211 1.174 -1002us 1329us

au.kashra.pictures 7 5 519 -0.645 10.414 -3117us 756us

sombrero.spiderspace.co.> 26 14 41m -0.165 0.780 +3008us 717us

---- sensors

-rw-r--r-- 1 root root 171 Nov 11 2018 /etc/sensors.d/draws

ads1015-i2c-1-48

Adapter: bcm2835 I2C adapter

User ADC Differential: +0.00 V

+12V: +12.34 V

User ADC 1: +0.00 V

User ADC 2: +0.00 V

---- locale

Locale country codes consistent among WiFi cfg file, iw reg & X11: US

core_config.sh has been run 1 time(s)

Sent from Mail for Windows 10

Rob Lapham
 

I did use Johns web app and it came up with the same values as the draws manager. I have turned  the gain up all the way and no clean tone.
the radio works fine with my other rp4 and a signal link so I think the radio is ok. also install another cable still no clean audio.
I lost
Rob k6jus

Mitch Winkle
 

sounds very much like my issue, only I have badly distored audio to the transmitter.  mine is in a box ready to be mailed back for eval.

On 8/28/19 10:08 PM, Rob Lapham wrote:
I did use Johns web app and it came up with the same values as the draws manager. I have turned  the gain up all the way and no clean tone.
the radio works fine with my other rp4 and a signal link so I think the radio is ok. also install another cable still no clean audio.
I lost
Rob k6jus

 

What radio model are you trying to drive?


On Thu, Aug 29, 2019, 04:34 Mitch Winkle <ab4mw@...> wrote:

sounds very much like my issue, only I have badly distored audio to the transmitter.  mine is in a box ready to be mailed back for eval.

On 8/28/19 10:08 PM, Rob Lapham wrote:
I did use Johns web app and it came up with the same values as the draws manager. I have turned  the gain up all the way and no clean tone.
the radio works fine with my other rp4 and a signal link so I think the radio is ok. also install another cable still no clean audio.
I lost
Rob k6jus

Mitch Winkle
 

FT-450D

On 8/29/19 9:39 AM, John D Hays - K7VE wrote:
What radio model are you trying to drive?

On Thu, Aug 29, 2019, 04:34 Mitch Winkle <ab4mw@...> wrote:

sounds very much like my issue, only I have badly distored audio to the transmitter.  mine is in a box ready to be mailed back for eval.

On 8/28/19 10:08 PM, Rob Lapham wrote:
I did use Johns web app and it came up with the same values as the draws manager. I have turned  the gain up all the way and no clean tone.
the radio works fine with my other rp4 and a signal link so I think the radio is ok. also install another cable still no clean audio.
I lost
Rob k6jus

Rob Lapham
 

It’s a ft-817nd

Basil Gunn
 

Have you read this to set up a "USER" defined digital mode on your
radio?

https://github.com/nwdigitalradio/n7nix/blob/master/docs/RADIO_APP_NOTES.md

/Basil n7nix

Rob Lapham
 

yes over and over went home to day and rechecked the radio settings. I would think if the radio work in receive and with a signal link the radio
settings should be right. last night had the drive turned all the way up and would not drive the radio just keys and no power. keep going over the 
settings and instruction's. 
Rob k6jus

 

The FT-817 is probably the most tested for the DRAWS™ HAT.

Are you using the left DIN-6 port and selecting the same in your program?

There is a possibility that one of the flags in the CODEC was set incorrectly, at some point.  Try using n7nix/bin/setalsa-ft817.sh  

Occasionally, we have seen the FT-817 where a parameter is changed from default, sometimes doing a full reset on the radio gets it to a working mode.



On Thu, Aug 29, 2019 at 9:14 AM Rob Lapham <ke6jus@...> wrote:
It’s a ft-817nd



--
John D. Hays
Kingston, WA
K7VE

 

Rob Lapham
 

just did a rest on the radio and still no transmit powers and also don't see how it can be the radio if it works with other soundcards.
just tried the setalsa-ft817.sh command again no joy I have also tried a new memory card and started over I have been at this for
about two months now. I have also tried the draws manager and turned the gain up to max and no transmit.

starting to think I made mistake buying this

rob k6jus



 

Fred Meier <fsmeier@...>
 

Rob, you are contributing to the advances of mankind. Think of your purchase as an investment in progress.

I follow this conversation daily. I ordered mine in early Spring- as soon as presales were allowed. I ordered my metal case as soon as that was offered.

The Draws hat arrived in the mail. After postage, duties, taxes and a service fee to the letter carrier this cost nearly $200.00 Canadian at my door.

I have never seen the case.

After following this convoluted thread for months- I think I made the right decision to not open the package. Unfortunately it is much too late to return mine.

You can either be sad about your purchase, or you can go outside and mow the lawn if you have one. Your choice.

Cheers, Fred VE7FMN

 

From: udrc@nw-digital-radio.groups.io <udrc@nw-digital-radio.groups.io> On Behalf Of Rob Lapham
Sent: Thursday, August 29, 2019 9:41 PM
To: udrc@nw-digital-radio.groups.io
Subject: Re: [draws and udrc] no transmit #wsjt-x

 

just did a rest on the radio and still no transmit powers and also don't see how it can be the radio if it works with other soundcards.
just tried the setalsa-ft817.sh command again no joy I have also tried a new memory card and started over I have been at this for
about two months now. I have also tried the draws manager and turned the gain up to max and no transmit.

starting to think I made mistake buying this

rob k6jus



 

Rob Lapham
 

well tried it all over with a signal link and the transmitter works then plugged in the hat and not enough audio to drive the radio so it can be the radio
and look like I am dead in the water. I have set the parameters over and over and they say check the same thing. I think this hat is dead and from reading
more problems out there. Shure would be helpful if the instructions were all together for some of us nubs that didn't know what we where getting into.

Rob k6jus

   

Jim Erickson
 

I believe with WSJTX you need to use CAT control to trigger the PTT as WSJTX does not have a GPIO option.  I would test your setup with FLDIGI and see if you can get it to trigger your radio as it has GPIO PTT option.

Jim
------
73,
Jim
VA7SHG - Phone
VE7TGZ - Other

On Aug 30, 2019, at 19:58, Rob Lapham <ke6jus@...> wrote:

well tried it all over with a signal link and the transmitter works then plugged in the hat and not enough audio to drive the radio so it can be the radio
and look like I am dead in the water. I have set the parameters over and over and they say check the same thing. I think this hat is dead and from reading
more problems out there. Shure would be helpful if the instructions were all together for some of us nubs that didn't know what we where getting into.

Rob k6jus

   

Rob Lapham
 

thanks Jim but the radio will  go into transmit but no power out there is not enough drive to show any power out . it has to 
be a audio problem

Rob k6jus 

Rob Lapham
 

well today I made a din brakeout cable to test the audio to the ft-817 with a o-scope and using
./measure_deviate.sh -c left there is no audio on pin 3 or any other pin. I tested with pin 6
connected and disconneted no difference. did the same test with a working sound card and wsjt-x
and have a good signal on the o-scope. what am I missing? Is there any other test I can do to the
hat. thanks

rob k6jus

Basil Gunn
 

Rob,

Lets confirm that measure_deviate.sh is working properly. Could you
please cut & paste the console output of all the commands below.

piver.sh
udrcver.sh

# Using o-scope check both left & right channels.

cd
cd n7nix/deviation
./measure_deviate.sh -c left
./measure_deviate.sh -c right

# Verify gpio 7 is set to correct mode
gpio readall | grep -i "gpio. 7"

Thanks,
/Basil

Rob Lapham <ke6jus@...> writes:

well today I made a din brakeout cable to test the audio to the ft-817 with a o-scope and using
./measure_deviate.sh -c left there is no audio on pin 3 or any other pin. I tested with pin 6
connected and disconneted no difference. did the same test with a working sound card and wsjt-x
and have a good signal on the o-scope. what am I missing? Is there any other test I can do to the
hat. thanks

rob k6jus

Rob Lapham
 

Here are the outputs
pi@k6jus:~/n7nix $ piver.sh
 Pi 3 Model B+ Mfg by Sony UK
 Has WiFi
pi@k6jus:~/n7nix $ udrcver.sh
Found a DRAWS
     HAT ID EEPROM
Name:        hat
Product:     Digital Radio Amateur Work Station
Product ID:  0x0004
Product ver: 0x0106
UUID:        9598845d-e110-49ce-9287-d770da081361
Vendor:      NW Digital Radio
pi@k6jus:~/n7nix/deviation $ ./measure_deviate.sh -c left
Using tone: 2200 (wave file name: 2200hzsin.wav) for duration 30 & left connector using gpio: 12
Found existing wav file: 2200hzsin.wav
If using devcal from Svxlink make sure devcal line has -f2200
Using PTT GPIO 12 with tone of 2200 Hz
Playing WAVE '2200hzsin.wav' : Signed 32 bit Little Endian, Rate 48000 Hz, Stereo
Hardware PCM card 1 'udrc' device 0 subdevice 0
Its setup is:
  stream       : PLAYBACK
  access       : RW_INTERLEAVED
  format       : S32_LE
  subformat    : STD
  channels     : 2
  rate         : 48000
  exact rate   : 48000 (48000/1)
  msbits       : 32
  buffer_size  : 24000
  period_size  : 6000
  period_time  : 125000
  tstamp_mode  : NONE
  tstamp_type  : MONOTONIC
  period_step  : 1
  avail_min    : 6000
  period_event : 0
  start_threshold  : 24000
  stop_threshold   : 24000
  silence_threshold: 0
  silence_size : 0
  boundary     : 1572864000
  appl_ptr     : 0
  hw_ptr       : 0
##################################################+| MAX^C
pi@k6jus:~/n7nix/deviation $ ./measure_deviate.sh
Using tone: 2200 (wave file name: 2200hzsin.wav) for duration 30 & right connector using gpio: 23
Found existing wav file: 2200hzsin.wav
If using devcal from Svxlink make sure devcal line has -f2200
Using PTT GPIO 23 with tone of 2200 Hz
Playing WAVE '2200hzsin.wav' : Signed 32 bit Little Endian, Rate 48000 Hz, Stereo
Hardware PCM card 1 'udrc' device 0 subdevice 0
Its setup is:
  stream       : PLAYBACK
  access       : RW_INTERLEAVED
  format       : S32_LE
  subformat    : STD
  channels     : 2
  rate         : 48000
  exact rate   : 48000 (48000/1)
  msbits       : 32
  buffer_size  : 24000
  period_size  : 6000
  period_time  : 125000
  tstamp_mode  : NONE
  tstamp_type  : MONOTONIC
  period_step  : 1
  avail_min    : 6000
  period_event : 0
  start_threshold  : 24000
  stop_threshold   : 24000
  silence_threshold: 0
  silence_size : 0
  boundary     : 1572864000
  appl_ptr     : 0
  hw_ptr       : 0
##################################################+| MAX
pi@k6jus:~ $ gpio readall
 +-----+-----+---------+------+---+---Pi 3B+-+---+------+---------+-----+-----+
 | BCM | wPi |   Name  | Mode | V | Physical | V | Mode | Name    | wPi | BCM |
 +-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
 |     |     |    3.3v |      |   |  1 || 2  |   |      | 5v      |     |     |
 |   2 |   8 |   SDA.1 | ALT0 | 1 |  3 || 4  |   |      | 5v      |     |     |
 |   3 |   9 |   SCL.1 | ALT0 | 1 |  5 || 6  |   |      | 0v      |     |     |
 |   4 |   7 | GPIO. 7 | ALT0 | 0 |  7 || 8  | 0 | IN   | TxD     | 15  | 14  |
 |     |     |      0v |      |   |  9 || 10 | 1 | IN   | RxD     | 16  | 15  |
 |  17 |   0 | GPIO. 0 |   IN | 1 | 11 || 12 | 1 | ALT0 | GPIO. 1 | 1   | 18  |
 |  27 |   2 | GPIO. 2 |   IN | 0 | 13 || 14 |   |      | 0v      |     |     |
 |  22 |   3 | GPIO. 3 |   IN | 0 | 15 || 16 | 0 | OUT  | GPIO. 4 | 4   | 23  |
 |     |     |    3.3v |      |   | 17 || 18 | 0 | IN   | GPIO. 5 | 5   | 24  |
 |  10 |  12 |    MOSI |   IN | 0 | 19 || 20 |   |      | 0v      |     |     |
 |   9 |  13 |    MISO |   IN | 0 | 21 || 22 | 0 | IN   | GPIO. 6 | 6   | 25  |
 |  11 |  14 |    SCLK |   IN | 0 | 23 || 24 | 1 | IN   | CE0     | 10  | 8   |
 |     |     |      0v |      |   | 25 || 26 | 0 | IN   | CE1     | 11  | 7   |
 |   0 |  30 |   SDA.0 |   IN | 1 | 27 || 28 | 1 | IN   | SCL.0   | 31  | 1   |
 |   5 |  21 | GPIO.21 |   IN | 1 | 29 || 30 |   |      | 0v      |     |     |
 |   6 |  22 | GPIO.22 |   IN | 1 | 31 || 32 | 0 | OUT  | GPIO.26 | 26  | 12  |
 |  13 |  23 | GPIO.23 |  OUT | 1 | 33 || 34 |   |      | 0v      |     |     |
 |  19 |  24 | GPIO.24 | ALT0 | 1 | 35 || 36 | 0 | IN   | GPIO.27 | 27  | 16  |
 |  26 |  25 | GPIO.25 |   IN | 0 | 37 || 38 | 0 | ALT0 | GPIO.28 | 28  | 20  |
 |     |     |      0v |      |   | 39 || 40 | 0 | ALT0 | GPIO.29 | 29  | 21  |
 +-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
 | BCM | wPi |   Name  | Mode | V | Physical | V | Mode | Name    | wPi | BCM |
 +-----+-----+---------+------+---+---Pi 3B+-+---+------+---------+-----+-----+
Ill have to study a liitle more on gpio pins

Thanks Rob k6jus