I have been trying to get this going all day, following the directions to the letter, it works for a little bit, once I think I have it, I reboot and it doesn't work! Levels never leave 100% DR1-X 1.

Hello; I am trying to configure the UDRC image to run the board on a Raspberry Pi 3 as a simplex hotspot.  I have followed the directions at the following link: https://nw-digital-radio.groups.i

Hi Trying to install packages on a compass image as per instructions in Wiki :sudo apt-get install dstarrepeater ircddbgatewayUnfortunately receiving these error messages: Err http://archive.compass

OK I wanted to check alsamixer settings using speaker-test to confirm audio transmit levels to radio from the udrc however I get the following: pi@pi3udrc:~ $ speaker-test -Dplughw:udrc speaker-test

I have tried to get dstartrepeaterd to beacon in some form the repeater's call and while it "looks" like it is doing something, no RF actually happens. From the Log: M: 2016-07-08 18:29:36: Transmit

All is working fine with my UDRC and DR-1X.  I have a 7100, ID-51, and an ID-5100.   But.... All the messages show up on the IC-7100 and ID-51.  But none show up on the 5100.  Aug AG5AT

We are aware that there seems to be a problem with some Raspberry Pi 3 installations for dstarrepeater, UDRC and Raspberry Pi 3. If you are having problems and have a Raspberry Pi 2 available, give it

By trial and error I have gotten my UDRC working on our recently upgraded DR-1X to v1.10J.  I followed the setup instructions from Northwest Digital Radio's Wiki and where the instructions were lackin

I can't figure out what I did to cause this to come on or how to shut it off. Its in wires-x software and it now won't let me connect to any rooms. I don't see anything in the manual that would tell

Some users have encountered reliability issues when the UDRC™ is used with a Raspberry Pi 3. NW Digital Radio has duplicated the problem and isolated its root cause. Our team looked at different opt

Hello, I have the following problem when a D-Star signal over the network / reflector comes then sends the Dr1 everything properly made, is a signal on the local input of the repeater is not abo

John, Finally I got the chance to set the fix. Have both working on V2 and or V3 with this fix. Thanks for all of the work done. 73 Steve NO9S

http://lopezhams.com/lpzhams/doku.php?id=lpzhams:udrc:msging -- ------------------------------ John D. Hays K7VE PO Box 1223, Edmonds, WA 98020-1223 <http://k7ve.org/blog> <http://twitter.com/#!/

When the udrc is connected and running on the DR1X the Dstar operates on the network just fine. I loose the wires-x network connectivity though. I see the network traffic come in on the software just

Page 151 in September 2016 QST

Using 1.0n repeater in configuration 4.  Followed the YouTube tutorial and ircddb wiki. RaspPi 2 When we boot the system up we get a message over D-Star that we are linking to XRF002A that we set. H

Testing...

I am trying to replace my old PI 1 on a homebrew repeater I have the gateway started but see no response when I key a radio. see lots of errors on the log file. i will copy them to this e-mail. E: 20

https://www.youtube.com/watch?v=au7aElLKUVk&feature=youtu.be&t=2160 -- by VE3MIC -- ------------------------------ John D. Hays Director <http://nwdigitalradio.com> PO Box 1223, Edmonds, WA 98020-

Can the UDRC be installed on a Pi 3 that has an 'Official' touch screen connected to the DSI connector? The display connects to the SDA and SCL (I2C) leads on the GPIO (pins 3 and 5). Will this inter