Paul, If you didn't change anything having to do with gpsd and it started working later, this usually indicates that the gps wasn't locked before: 1. The gps loses ephemeris data if the board is power

If I send an APRS message with the tracker to my home station, and the ack box is checked, I do not see the ack response from the base station. I can see that the base station sent a packet in the 1-8

I have been running this Software on 2 of my Repeater for several years and it has been working great until recently one of them had the SD Card fail. Is this Web page based Software still available o

Basil, when you use nixtracker mobile, what are you using for a display and is it hardwired to the RPi or not? tia, David, Ke7rgp

Basil, I have installed your NWDR15 image and followed all of your getting started steps with the exception below in 1) and have a few issues/questions: 1) Was it a mistake to set my own pwd on the fi

Basil, Now with XASTIR running I am attempting to set up the interface with DRAWS via Interface Control: Interface type AX25 TNC, and AX.25 Device Name udr0. Interface START has no effect, the interfa

Two problems: with ax25 started I do a wl2kax25 - k2wvc-10 (a gateway on 2 met4ers). It connects but hangs after a Challenge is received. Eventually it times out with jibberish and disconnects Console

I am working to test WSJT-s on the latest image of DRAWS image. I have connected a USB to serial adapter plugged in to the COM port on the radio and have a DIN cable between the UDC0 and the data port

Hi, With nwdr15.img and recently with nwdr14.img I observed same desktop issues on two different Raspberry Pi models 3B+ and 4 and two different screen displays models. *These issues are not present o

I “crashed” my micro sd card using a non- draws related program. I reloaded the earlier version of software that I had been using which had been working on to that sd card. The wsjt-x program comes up

Ok folks, I have installed Direwolf with a DRAWS hat using the basic Raspbian image with desktop only. 1) My APRS info is getting through IGate but is unverified and is not present APRS.fi raw data, p

To the Group: I am starting a new build from scratch using the new Version 15 image and have found the first gotcha during the first boot, just before doing the OS updates. I had a dead battery in the

Release image nwdr15 Jan 23, 2020 last image nwdr14 Oct 07, 2019 Latest RPi image current_image.zip has been updated to nwdr15.zip at this location: http://images.nwdigitalradio.com/downloads There we

J P, I'm not very motivated to write a configuration back-up program. The following is my thinking, flawed as it may be. 1. I can regen any of my RPi units from a blank mSD card in 30 minutes or less.

With NorthWestDigital radio Debian image nw14, AX25 over UDP is not working. Although configuration is correct there is no frames transmitted nor received via the axudp interface. After reinstalling A

John, I saw that you referenced that you were able to run 9600 and or 1200 on a single radio interface. Can you refer us to the code, configuration that allows for on the fly switchng between Direwolf

Is there a guide for setting up the DRAWS hat with Buster? I started with a clean image, and tried to enable the DRAWS by adding `dtoverlay=draws` to the /boot/config.txt file, but when the pi starts,

k7udr posted: "We are on track to receive the final prototypes Feb 15th, at which time we can place the production order for the Early Adopter and production cases. Thanks for your patience." New post

I recently added a Xiegu G90 to my "shack" and I want to set it up with my DRAWS hat. I believe I've figured out the right way to connect it up, currently via the CE-19 adapter board, but I'll probabl

Morning, I found this morning a bunch of UDRC boards that I "lost" in a house move. A project that I put on the long finger quite a while ago was a DMR to Analog Bridge to get our local Analogue Repea