Greetings Basil N7NIX, If things go right tomorrow, I might try installing URONODE on the image NW15. I really would like to figure out how to run the nodesearch plugin. Any advice would be appreciate

Hello- I have an unused DRAWS with a Pi3 and DRAWS image in orig USPS box and packaging. This has 2 radio cables and GPS antenna. I really do not have the time or ability at this point to use it so I

I am going to make some cables, starting with CAT control. What pins on the L/R mini dins are for cat levels plaese? I will keep struggling with the software at a later stage. It is all very muddy, as

I guess i am on my own then..... -- MY GMAIL desktop Email accoount, JF McRae, VK5PO/VK5SIX

Hi guys. I have connected a power supply to the draws hat, but when I switch the supply on, the Pi does not 'start'. the cooling fans are working, I see the GREEN LED on the Pi illuminated continually

I am finally having some success with my Pi 4b I ended up not using the NWDIG .img So, having gotten fldigi working ok, Including CAT ctrl I now need to ONLY INSTALL draws lib components to utilise th

Hi everyone. Slowly working my way around the DRAWS/Rasp Pi... I would like to know the sound codex I/O information please. Seems a lot of options to choose from. That is for setting up JS8Call at thi

I have started A FB group with the aim of helping out / being helped fellow users of the DRAWS HAT, as I navigate my way through getting it all up and running. I have WSJT-X up on the screen, but need

Paul, If you didn't change anything having to do with gpsd and it started working later, this usually indicates that the gps wasn't locked before: 1. The gps loses ephemeris data if the board is power

If I send an APRS message with the tracker to my home station, and the ack box is checked, I do not see the ack response from the base station. I can see that the base station sent a packet in the 1-8

I have been running this Software on 2 of my Repeater for several years and it has been working great until recently one of them had the SD Card fail. Is this Web page based Software still available o

Basil, when you use nixtracker mobile, what are you using for a display and is it hardwired to the RPi or not? tia, David, Ke7rgp

Basil, I have installed your NWDR15 image and followed all of your getting started steps with the exception below in 1) and have a few issues/questions: 1) Was it a mistake to set my own pwd on the fi

Basil, Now with XASTIR running I am attempting to set up the interface with DRAWS via Interface Control: Interface type AX25 TNC, and AX.25 Device Name udr0. Interface START has no effect, the interfa

Two problems: with ax25 started I do a wl2kax25 - k2wvc-10 (a gateway on 2 met4ers). It connects but hangs after a Challenge is received. Eventually it times out with jibberish and disconnects Console

I am working to test WSJT-s on the latest image of DRAWS image. I have connected a USB to serial adapter plugged in to the COM port on the radio and have a DIN cable between the UDC0 and the data port

Hi, With nwdr15.img and recently with nwdr14.img I observed same desktop issues on two different Raspberry Pi models 3B+ and 4 and two different screen displays models. *These issues are not present o

I “crashed” my micro sd card using a non- draws related program. I reloaded the earlier version of software that I had been using which had been working on to that sd card. The wsjt-x program comes up

Ok folks, I have installed Direwolf with a DRAWS hat using the basic Raspbian image with desktop only. 1) My APRS info is getting through IGate but is unverified and is not present APRS.fi raw data, p

To the Group: I am starting a new build from scratch using the new Version 15 image and have found the first gotcha during the first boot, just before doing the OS updates. I had a dead battery in the