I am struggling to send email peer to peer where the end station is using PC based WinLink and only has the call sign AB9DEF without the -10. wl2kax25 -c WA9APQ?? This returns : connect(): Address alr

Peer to Peer receive is not activating when an inbound request it received. I see it in a terminal window using the listen command. What do I need to change to receive inbound Peer to Peer? Ed Bloom,

New post on NW Digital Radio DRAWS Shipping Status: by k7udr As of today all backorders have been filled on DRAWS Boards. We now have 30 boards IN STOCK! We have started a new run so we should have st

I am able to send to any RMS Gateway station I can hear and at the same time any mail for me is picked up. Ed Bloom, KD9FRQ ewbloom@... Sent from Webmail access

How do I expand the command below to send to CALL-10 via my local digipeater through a second digitpeater? wl2kax25 -c CALL-10 In "packet" land, the command is : wl2kax25 -c DIGI-1 DIGI-2 CALL-10 I al

Tue, Jul 14 at 5:09 PM I have just installed my draws hat with the your latest image from your directions and I can not find the correct sound card settings for the draws and any ham radio program. Wh

Before updating to the latest image and now, since updating, my Winlink Gateway is working properly, folks can get into it and upload/download their messages. The one part that isn't working is that I

My trusty crusty TM-D700 finally gave up and I wanted to build a new mobile rig based around an FT-897 that hasn’t seen much use since upgrading my home station. Going through the parts bin I found my

Hey all, I have started with a fresh install of nwdr16. I am following this: https://nw-digital-radio.groups.io/g/udrc/wiki/8949 and I'm in the "Test Transmit" phase - so far everything works. I have

Hi, Ran through the following and now the PI won't boot. Does not even appear to try. This is a PI 3. I did enable the HDMI Safe flag just in case it would help. sudo apt-get update sudo apt-get dist-

I have been using my original UDRC and direwolf for a long time as one of the ports on my bpq32 node. A while back the SD card on that Pi went belly up so I rebuilt the system from scratch using the c

The Pi has Bluetooth and WiFi. Is there a way to have PAT send a notification that "I've Got Mail" if there is a new message received via wl2kax25 command? 73s, Ed, KD9FRQ

Hi All and Happy New Year. Basil, I believe I read on here somewhere that you were working on the split-channel operation of the Draws and making so that you could do HF and APRS/Packet with two diffe

Good evening Basil. I believe there is an error in hf_verchk.sh finding the current wsjtx version and updating from source: pi@KD5MDRAWS:~/n7nix/hfprogs $ ./hf_verchk.sh js8call: current version: 2.1.

Hi everybody, I would like to install a simple pushbutton to shutdown or reboot the pi with the DRAWS hat sitting on it. To write the scripts is not a big deal. But I need to know which GPIO pins I co

Is any news available on filling orders currently listed as "Backordered"? Thomas Noel /KF7RSF

With DRAWS™ Support ---------- Forwarded message --------- From: Dave Slotter, W3DJS <slotter@...> Date: Thu, Jun 18, 2020, 21:09 Subject: [RaspberryPi-4-HamRadio] HamPi 1.0 Released! To: <RaspberryPi

Craig, I won't know much until I see some console output from the RMS Gateway device. If I had to guess, since N0CSM-10 is not showing up in the Winlink packet RMS list, you did not configure the Winl

Hello, I've asked, end of last year, for a cancellation of the case order I did. I've never had any news. Now that the case is produced, will i get one or will i be reimbursed ? I understand you have

Not sure how to set up the IPTables for AX.25, so I used my wireless access to my router during the config setup I used the IP address twice during the setup. Unfortunately, the information to set up